Digital Projection Titan 930 User manual

Rev A January 2014
USER MANUAL
INSTALLATION AND QUICK-START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
REMOTE COMMUNICATIONS GUIDE
REFERENCE GUIDE
115-072A
M-Vision 930 Series
High Brightness Digital Video Projector

Digital Projection M-Vision 930 Series NoTOC
i
Rev A January 2014
Digital Projection M-Vision 930 Series
i
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2014 Digital Projection Ltd. All rights reserved.
Notes

Digital Projection M-Vision 930 Series NoTOC
ii
Rev A January 2014
Digital Projection M-Vision 930 Series
ii
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• Support for most 3D formats.
• HDBaseT® for transmission of uncompressed High Denition Video up to 100 m from the source.
• Edge Blend.
• Blanking control for custom input window sizing.
• Cornerstone, Vertical & Horizontal Keystone, Pincushion & Barrel, and Image Rotation.
• Control via LAN and RS232.
• Motorised lens mount.
A serial number is located on the back of the projector. Record it here:
Notes

Digital Projection M-Vision 930 Series NoTOC
iii
Rev A January 2014
Digital Projection M-Vision 930 Series
iii
CONTENTS
INSTALLATION AND QUICK-START GUIDE ..............................1
WHAT’S IN THE BOX? ................................................................... 3
CONNECTING THE POWER SUPPLY ............................................. 4
PROJECTOR OVERVIEW ............................................................... 5
Front and rear views ............................................................................. 5
Control panel indicators ........................................................................ 6
REMOTE CONTROL....................................................................... 7
Infrared reception.................................................................................. 9
POSITIONING THE SCREEN AND PROJECTOR........................... 10
CHANGING THE LENS................................................................. 11
Inserting a new lens ............................................................................ 11
Removing the lens .............................................................................. 12
CHANGING THE FILTERS ............................................................ 13
CHANGING THE LAMPS .............................................................. 15
OPERATING THE PROJECTOR.................................................... 17
Switching the projector on................................................................... 17
Switching the projector off................................................................... 17
Selecting an input signal or test pattern.............................................. 18
Input signal ........................................................................................ 18
Test pattern ........................................................................................ 18
Adjusting the lens................................................................................ 19
Adjusting the image............................................................................. 20
Orientation ......................................................................................... 20
Keystone ........................................................................................... 20
Picture .............................................................................................. 20
CONNECTION GUIDE ............................................................................21
SIGNAL INPUTS .......................................................................... 23
Digital inputs and outputs.................................................................... 23
Analog inputs ...................................................................................... 24
EDID on the DVI and VGA inputs........................................................ 25
Using HDMI/DVI switchers with the projector ..................................... 25
3D connections ................................................................................... 26
3D sources up to 60Hz requiring frame doubling and left/right interleaving.......... 26
Frame sequential 3D sources up to 120Hz ................................................. 26
Dual Pipe 3D ...................................................................................... 26
3D Sync............................................................................................... 27
3D Sync in ......................................................................................... 27
3D Sync out ....................................................................................... 27
CONTROL CONNECTIONS........................................................... 28
LAN connection examples .................................................................. 29
RS232 connection example ................................................................ 30

Digital Projection M-Vision 930 Series NoTOC
iv
Rev A January 2014
Digital Projection M-Vision 930 Series
iv
OPERATING GUIDE ................................................................................31
USING THE MENUS ..................................................................... 33
Opening the OSD................................................................................ 33
Opening a menu.................................................................................. 33
Exiting menus and closing the OSD.................................................... 33
Inside a menu...................................................................................... 34
Accessing sub-menus........................................................................... 34
Executing commands............................................................................ 34
Editing projector settings..................................................................... 35
Choosing a value from a list ................................................................... 35
Changing the value without viewing the list................................................. 35
Using a slider to set a value.................................................................... 35
USING THE PROJECTOR............................................................. 36
Main menu .......................................................................................... 36
Aspect Ratio....................................................................................... 37
Presets ............................................................................................. 38
Overscan........................................................................................... 39
3D Control ......................................................................................... 40
3D types............................................................................................ 41
Some 3D settings explained ................................................................... 42
Main menu continued from previous page .................................................. 43
Frame rate multiplication in 3D images ...................................................... 43
Input Select........................................................................................ 44
Resync ............................................................................................. 44
Image menu ........................................................................................ 45
Advanced Image menu ....................................................................... 46
Colorspace ........................................................................................ 46
Gamma............................................................................................. 46
Color Temperature ............................................................................... 46
Dynamic Black .................................................................................... 47
Adaptive Contrast ................................................................................ 47
RGB Adjust ........................................................................................ 47
Fine Sync .......................................................................................... 48
Lamps menu ....................................................................................... 49
Alignment menu .................................................................................. 50
Lens Control....................................................................................... 51
Center Lens ....................................................................................... 51
Warp ................................................................................................ 52
Blanking ............................................................................................ 56
Edge Blend ........................................................................................ 57
Control menu....................................................................................... 59
OSD Settings...................................................................................... 60
Service menu ...................................................................................... 61
Factory Reset ..................................................................................... 61
CONTENTS (continued)

Digital Projection M-Vision 930 Series NoTOC
v
Rev A January 2014
Digital Projection M-Vision 930 Series
v
REMOTE COMMUNICATIONS GUIDE ..........................................63
INTRODUCTION........................................................................... 65
Network setup ..................................................................................... 65
Serial Port setup.................................................................................. 65
Remote communications commands.................................................. 66
Examples .......................................................................................... 66
COMMAND GUIDE ....................................................................... 67
MAIN menu ......................................................................................... 67
IMAGE menu....................................................................................... 68
ADVANCED menu .............................................................................. 69
LAMPS menu...................................................................................... 70
ALIGNMENT menu ............................................................................. 70
CONTROL menu................................................................................. 71
SERVICE menu .................................................................................. 72
Miscellaneous commands................................................................... 73
REFERENCE GUIDE................................................................................75
THE DMD™.................................................................................. 78
CHOOSING A LENS ..................................................................... 80
Basic calculation ................................................................................. 81
Basic calculation example................................................................... 82
Full lens calculation............................................................................. 83
Introducing TRC .................................................................................. 83
Calculating TRC .................................................................................. 84
Calculating the throw ratio with TRC ......................................................... 85
Full lens calculation example .............................................................. 86
SCREEN REQUIREMENTS........................................................... 87
Fitting the image to the DMD™........................................................... 87
WUXGA images displayed full width ......................................................... 87
WUXGA images displayed with a height of 1080 pixels.................................. 88
WUXGA images displayed full height ........................................................ 89
Diagonal screen sizes......................................................................... 90
Fitting the image to the screen............................................................ 91
Positioning the screen and projector................................................... 92
POSITIONING THE IMAGE........................................................... 93
Maximum offset range......................................................................... 95
ASPECT RATIOS EXPLAINED...................................................... 96
Aspect ratio examples......................................................................... 97
FRAME RATES AND PULLDOWNS EXPLAINED........................... 99
Interlaced and progressive scan ......................................................... 99
Frame rates of image sources ............................................................ 99
Pulldowns - conversion into destination formats............................... 100
2:3 (normal) pulldown ......................................................................... 100
2:3:3:2 (advanced) pulldown................................................................. 101
APPENDIX A: LENS PART NUMBERS........................................ 102
APPENDIX B: LENS CHARTS .................................................... 103
How to use the lens charts ................................................................... 103
TRC values applied in the charts ........................................................... 104
Full DMD™ width images..................................................................... 105
1.25:1 images ................................................................................... 106
1.33:1 images ................................................................................... 107
CONTENTS (continued)

Digital Projection M-Vision 930 Series NoTOC
vi
Rev A January 2014
Digital Projection M-Vision 930 Series
vi
APPENDIX C: SUPPORTED SIGNAL INPUT MODES .................. 108
2D input modes................................................................................. 108
3D input modes................................................................................. 110
APPENDIX D: MENU MAP...........................................................112
APPENDIX E: WIRING DETAILS..................................................117
Signal inputs and outputs.................................................................. 117
VGA ............................................................................................... 117
HDMI 1 and 2 ................................................................................... 118
DVI ................................................................................................ 119
Component 2.................................................................................... 120
Control connections .......................................................................... 121
LAN ............................................................................................... 121
RS232 ............................................................................................ 121
Trigger 1 & Trigger 2 ........................................................................... 122
Wired remote control .......................................................................... 122
USB ............................................................................................... 122
3D Sync IN and 3D Sync OUT .............................................................. 122
APPENDIX F: GLOSSARY OF TERMS........................................ 123
CONTENTS (continued)
TECHNICAL SPECIFICATIONS .................................................. 134
Models............................................................................................... 134
Inputs and outputs............................................................................. 135
Bandwidth ......................................................................................... 135
Remote control and keypad .............................................................. 135
Automation control ............................................................................ 135
Color temperature ............................................................................. 135
Lenses............................................................................................... 136
Lens mount ....................................................................................... 136
Mechanical mounting ........................................................................ 136
Orientation......................................................................................... 136
Electrical and physical specications................................................ 137
Safety & EMC regulations................................................................. 137

Digital Projection M-Vision 930 Series
This page is intentionally left blank.

Rev A January 2014
INSTALLATION AND QUICK-START GUIDE
M-Vision 930 Series
High Brightness Digital Video Projector

Digital Projection M-Vision 930 Series IN THIS GUIDE Installation and Quick-Start Guide
Rev A January 2014
IN THIS GUIDE
What’s In The Box?............................................................................................. 3
Connecting The Power Supply........................................................................ 4
Projector Overview............................................................................................. 5
Front and rear views ...................................................................................................5
Control panel indicators.............................................................................................6
Remote Control.................................................................................................... 7
Infrared reception........................................................................................................9
Positioning The Screen And Projector....................................................... 10
Changing The Lens........................................................................................... 11
Inserting a new lens..................................................................................................11
Removing the lens ....................................................................................................12
Changing The Filters........................................................................................ 13
Changing The Lamps ....................................................................................... 15
Operating The Projector ................................................................................. 17
Switching the projector on.......................................................................................17
Switching the projector off.......................................................................................17
Selecting an input signal or test pattern.................................................................18
Input signal......................................................................................................................18
Test pattern .....................................................................................................................18
Adjusting the lens .....................................................................................................19
Adjusting the image..................................................................................................20
Orientation ......................................................................................................................20
Keystone .........................................................................................................................20
Picture.............................................................................................................................20

Digital Projection M-Vision 930 Series WHAT’S IN THE BOX? Installation and Quick-Start Guide
3
Rev A January 2014
What’s In The Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
Remote control
(112-196)
2x AA batteries
User Guides on CD
(115-071)
Important Information (115-073)
Power cable, Europe
(112-001)
Power cable, North America
(112-002)
Projector (114-259)
Power cable, United Kingdom
(112-000)
2
PIC
MUTE
4
B
SHARP
O-SCAN NR
GAMMA
C-TEMP TEST
LENS
3D
SWAP
3D
FORMAT
2D/3D
ENTER
SOURCE
3
5
1
ASPECT
RATIO
MENU
USER MEMORY
C
A
|
ON POWER OFF
HDMI cable

Digital Projection M-Vision 930 Series CONNECTING THE POWER SUPPLY Installation and Quick-Start Guide
4
Rev A January 2014
Connecting The Power Supply
1. Make sure the voltage switch is
set to the correct voltage.
2. Make sure the mains power
button is in the OFF position.
3. Lift the cable lock up, push the
mains connector in rmly and push
the lock down to secure the cable.
4. Switch the mains power button
ON.
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.
31 2
1Voltage switch
1Mains power button
1AC mains inlet with cable lock

Digital Projection M-Vision 930 Series PROJECTOR OVERVIEW Installation and Quick-Start Guide
5
Rev A January 2014
Projector Overview
Front and rear views
1Air inlet
2Lens
3Front infrared window
4Air inlet
5Connection panel
6Control panel
7Rear infrared window
8Lamp enclosures with air outlets
9Mains inlet with power button and voltage switch
10 Air outlet
11 Adjustable feet
12 Air inlet
Notes
Front view
2
3
1
11
4
Rear view
8
7
6
5
9
12
10

Digital Projection M-Vision 930 Series PROJECTOR OVERVIEW Installation and Quick-Start Guide
6
Rev A January 2014
Control panel indicators
During power on, all LED indicators become lit while the projector is
running a self test.
At the end of the self test only the STANDBY indicator remains lit.
When the projector goes from STANDBY to ON mode, the STANDBY
indicator is switched off and the ON indicator is lit.
The ON indicator ashes during cool down.
Indicators
1ON
2ERROR
3STANDBY
Error codes
If the projector detects an error, the red ERROR indicator will ash as shown in the chart below.
For example, if the lamp door is left open, the ERROR indicator will ash twice followed by a pause, then the sequence will repeat until the
error condition is corrected.
Condition ERROR indicator behavior
Lamp fail Flashes once, then pauses, then repeats.
Lamp door open Flashes twice, then pauses, then repeats.
Fan failure Flashes three times, then pauses, then repeats.
Over temperature Flashes four times, then pauses, then repeats.
Filter failure Flashes ve times, then pauses, then repeats.
System error On.
ENTER
ON ERROR LED STATUS STANDBY
MENU STBY
INPUT
1 32
Notes
During startup all LEDs light up
at the same time to indicate the
projector is carrying out a self-test.
delay
delay
delay
delay
delay

Digital Projection M-Vision 930 Series REMOTE CONTROL Installation and Quick-Start Guide
7
Rev A January 2014
Remote Control
1Power ON / OFF
2Input selection
Select input source.
3Navigation
Navigate through the menus with the arrows, conrm your choice with ENTER.
4MENU
Access the projector OSD (on-screen display).
5User Memory
Load preset A, B or C.
6CONTRAST
Bring up the Contrast control, then adjust the value with the LEFT and RIGHT
arrow buttons..
7GAMMA
Switch to the next Gamma value:
...1.0, 1.8, 2.0, 2.2, 2.35, 2.5...
8LENS
Adjust lens position, zoom and focus with the arrow buttons.
92D/3D
Switch between 2D and 3D mode.
10 PIC MUTE
Close the shutter.
It takes a few seconds to switch the image back on.
11 ASPECT RATIO
Switch to the next aspect ratio:
...16:9, TheaterScope, 4:3, 4:3 Narrow, 16:10, 5:4, Native...
continues on next page...
Notes
Input selection buttons:
• 1- HDMI 1
• 2- VGA
• 3- Component 2
• 4 - Component 1
• 5- DVI
You can create and later recall up
to four presets using the OSD. For
further information, see Presets in
the Operating Guide.
Presets can also be recalled through
protocol. For further information,
see MAIN menu in the Remote
Communications Guide.
Remote control
2
PIC
MUTE
4
B
SHARP
O-SCAN NRGAMMA
C-TEMP TESTLENS
3D
SWAP
3D
FORMAT
2D/3D
ENTER
SOURCE
3
5
1
ASPECT
RATIO
MENU
USER MEMORY
CA
|
ON POWER OFF
1
2
4
5
7
9
10
3
11
6
8

Digital Projection M-Vision 930 Series REMOTE CONTROL Installation and Quick-Start Guide
8
Rev A January 2014
Remote control - continued from previous page
12 BRIGHTNESS
Bring up the Brightness control, then adjust the value with the LEFT and
RIGHT arrow buttons.
13 O-SCAN
Switch to Overscan mode:
...Off, Crop, Zoom...
14 C-TEMP
Switch to the next color temperature:
...5400K, 6500K, 7500K, 9300K, Native...
15 3D SWAP
Switch 3D source dominance from left to right eye (left eye signal rst) and vice
versa.
16 SHARP
Bring up the Sharpness control, then adjust the value with the LEFT and
RIGHT arrow buttons.
17 NR
Bring up the Noise Reduction control, then adjust the value with the LEFT and
RIGHT arrow buttons.
18 TEST
Show a test pattern. Press again to show the next test pattern:
...Off, White, Black, Red, Green, Blue, CheckerBoard, CrossHatch, V Burst,
H Burst, ColorBar...
19 3D FORMAT
Switch between 3D formats as follows:
...Off, Auto, Side-by-Side (Half), Top-and-Bottom, Dual Pipe, Frame
Sequential...
Notes
Remote control
2
PIC
MUTE
4
B
SHARP
O-SCAN NRGAMMA
C-TEMP TESTLENS
3D
SWAP
3D
FORMAT
2D/3D
ENTER
SOURCE
3
5
1
ASPECT
RATIO
MENU
USER MEMORY
CA
|
ON POWER OFF
13
15
16
12
14
17
18
19

Digital Projection M-Vision 930 Series REMOTE CONTROL Installation and Quick-Start Guide
9
Rev A January 2014
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of acceptance
when trying to control the projector.
40°
40°
Infrared reception
Notes
The infrared receivers are disabled
when a remote control is connected
via a cable. For more information,
see Wired remote control in the
Connection Guide.

Digital Projection M-Vision 930 Series POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
10
Rev A January 2014
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen. Set the adjustable feet so that
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the xing holes for ceiling mounting.
1Four adjustable feet
2Six M6 holes for ceiling mount
The screws should not penetrate more than 15 mm into the body of the projector.
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least 30
cm (12 in) of space between the
ventilation outlets and any wall,
and 10 cm (4 in) on all other
sides.
Do not stack more than 3
projectors.
Do not tilt the projector more than
±12° from side to side when in
use, as this may cause system
failure.
±12° 360°
1
2
1
1
1
2
2
2
2
2

Digital Projection M-Vision 930 Series CHANGING THE LENS Installation and Quick-Start Guide
11
Rev A January 2014
Changing The Lens
Inserting a new lens
1. Remove the lens cover.
2. Insert the lens, keeping
the connector in upright
position.
3. Rotate the lens clockwise
until it clicks into place.
Notes
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Take care to preserve the original
lens packaging and protective caps
for future use.

Digital Projection M-Vision 930 Series CHANGING THE LENS Installation and Quick-Start Guide
12
Rev A January 2014
Removing the lens
1. Push the button 1all the way in.
2. Rotate the lens counterclockwise 2until it disengages.
3. Slowly pull the lens out 3.
Notes
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Take care to preserve the original
lens packaging and protective caps
for future use.
1 32