Digital Projection M-Vision Cine 400 3D series User manual

M-Vision Cine 400 3D series
High Brightness Digital Video Projector
16:9 widescreen display
Revision C, July 2014 112-853C
USER GUIDES
INSTALLATION AND QUICK START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
REMOTE COMMUNICATIONS GUIDE

This page is intentionally left blank.

M-Vision Cine 400 3D series
High Brightness Digital Video Projector
16:9 widescreen display
Revision C, July 2014 112-854C
INSTALLATION AND QUICK-START GUIDE

Digital Projection M-Vision Cine 400 3D series Installation and Quick-Start Guide
Revision C, July 2014
CONTENTS
Important information ............................................................ Inst-01
Symbols used in this guide............................................................................. Inst-01
Special formatting............................................................................................ Inst-01
Product revision............................................................................................... Inst-01
What’s in the box?.................................................................. Inst-02
Getting to know the projector ............................................... Inst-03
Front and rear views ........................................................................................ Inst-03
Remote control................................................................................................. Inst-03
Control panel and indicators........................................................................... Inst-04
Power indicator (blue light).......................................................................Inst-04
Error codes (red light) ..............................................................................Inst-05
Positioning the screen and projector................................... Inst-06
Operating the projector.......................................................... Inst-07
Switching the projector on.............................................................................. Inst-07
Switching the projector off.............................................................................. Inst-07
Adjusting the lens ............................................................................................ Inst-08
Zoom........................................................................................................Inst-08
Focus .......................................................................................................Inst-08
Shift..........................................................................................................Inst-08
Selecting an input signal or test pattern........................................................ Inst-09
Input signal...............................................................................................Inst-09
Test pattern ..............................................................................................Inst-09
Adjusting the image......................................................................................... Inst-10
Orientation................................................................................................Inst-10
Aspect ratio ..............................................................................................Inst-10
Picture......................................................................................................Inst-10
3D.............................................................................................................Inst-10

Digital Projection M-Vision Cine 400 3D series IMPORTANT INFORMATION Installation and Quick-Start Guide
Revision C, July 2014 Inst-01
Important information
Please keep this guide handy for future reference.
A serial number is located on the side of the projector. Please record it here:
Symbols used in this guide
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING
This symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless the instructions are closely followed.
FURTHER INFORMATION
This symbol shows important additional information.
Special formatting
●Buttons on the projector control panel or the remote control appear in BLOCK CAPITALS, e.g. MENU. Where necessary, the name of a button is followed by an image, e.g. ON .
●Menu titles and menu items appear in Bold, e.g. the System menu.
●If the described state of the equipment is named, the state appears in CAPITALS, e.g. STANDBY mode.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features without prior notice.

Digital Projection M-Vision Cine 400 3D series WHAT’S IN THE BOX? Installation and Quick-Start Guide
Revision C, July 2014
What’s in the box?
2
PIC
MUTE
4
B
SHARP
O-SCAN NR
GAMMA
C-TEMP TEST
BRI-C
3D
SWAP
3D
FORMAT
2D/3D
ENTER
SOURCE
3
6
1
ASPECT
RATIO
MENU
USER MEMORY
C
A
|
ON POWER OFF
Notes
Make sure your box contains
everything listed. If any pieces
are missing, please contact your
dealer.
You should save the original box
and packing materials in case you
ever need to ship your projector.
Inst-02
Remote control (109-685) 2 x AAA batteries Cine 400 3D projector
User Manual on disc
(115-759)
Important Information (110-287) 5mm Allen wrench 3D sync cable
Power cable 10A, United
Kingdom (102-180)
Power cable 10A, Europe
(102-163)
Power cable 13A, North
America (102-165)

Digital Projection M-Vision Cine 400 3D series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Revision C, July 2014
Getting to know the projector Notes
The projector uses the standard
MVision series infra-red remote
control.
Some of the controls are
duplicated on the projector control
panel, as shown on the next page.
For full details of how to use the
controls and the menu system,
see the Operating Guide.
Inst-03
Lens shift controls
(under the badge)
Front and rear views Remote control
Front
infrared
sensor
Lens
Focus
adjustment Zoom
adjustment
Air outlet
Air outlet
Control panel Rear infrared sensor
Air outlet
Air inlets
Adjustable feet
Lamp cover
Mains input
Connection panel
2
PIC
MUTE
4
B
SHARP
O-SCAN NRGAMMA
C-TEMP TESTBRI-C
3D
SWAP
3D
FORMAT
2D/3D
ENTER
SOURCE
3
6
1
ASPECT
RATIO
MENU
USER MEMORY
CA
|
ON POWER OFF
40°
40°
Infrared reception

Digital Projection M-Vision Cine 400 3D series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Revision C, July 2014
Control panel and indicators
Some of the functions on the remote control are duplicated on the projector control panel, as shown here.
MENU
MENU
POWER
POWER
ISSUE
ISSUE
LED STATUS
LED STATUS
POWER
POWER
S
E
L
E
C
T
S
E
L
E
C
T
SOURCE
SOURCE
Power indicator (blue light)
The blue Power indicator will light when the projector is in STANDBY mode, and will ash when the projector is cooling down or warming
up, as shown in the chart below. It will be off when the projector is in normal running mode.
Condition Power indicator behaviour (blue light)
Standby On
Cooling / Warming up Flashing
Power on (Normal) Off
Notes
For full details of how to use the
controls and the menu system,
see the Operating Guide.
Inst-04

Digital Projection M-Vision Cine 400 3D series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Revision C, July 2014
Error codes (red light)
If the projector detects an error, the red Issue indicator will ash as shown in the chart below.
For example, if the lamp door is left open, the red indicator will ash twice followed by a pause, then the sequence will repeat until the error
condition is corrected.
Condition Issue indicator behaviour (red light)
Lamp fail Flashes once, then pauses, then repeats.
Lamp door open Flashes twice, then pauses, then repeats.
Fan fail Flashes three times, then pauses, then repeats.
Over temperature Flashes four times, then pauses, then repeats.
System error On.
Notes
For full details of how to use the
controls and the menu system,
see the Operating Guide.
Inst-05
delay
delay
delay
delay

Digital Projection M-Vision Cine 400 3D series POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
Revision C, July 2014
Positioning the screen and projector
Consider the following:
●When installing the screen, ensure that it is in the best position for viewing by your audience.
● When positioning the projector, ensure that it is at a suitable distance from the screen for the image to ll the screen.
●Whether you are mounting the projector on the ceiling or standing it on its adjustable feet, ensure that it is level and perpendicular to
the screen.
The dimension drawing below shows the positions of the feet for table mounting, and the xing holes for ceiling mounting.
Notes
All dimensions on the diagram on
this page are in mm.
Ensure that there is at least
30cm (12in) of space between
the ventilation outlets and
any wall, and 10cm (4in) on all
other sides.
Do not stack more than 3
projectors.
Do not tilt the projector more
than ±12° from side to side
when in use, as this may cause
serious lamp failure, damage
the lamp module and cause
extra cost on replacement.
The projector may be tilted
to one side and positioned in
portrait mode as long as the
exhaust outlet points upward.
When positioning the projector
in portrait mode, ensure
adequate airow to the air
inlet.
Inst-06
±12° ±12°

Digital Projection M-Vision Cine 400 3D series OPERATING THE PROJECTOR Installation and Quick-Start Guide
Revision C, July 2014
Operating the projector
Switching the projector on
1. Connect the power cable between the mains supply and the projector. The projector begins a self-test.
2. When the self-test has completed, the power indicator on the projector control panel shows blue to indicate that the projector is in
STANDBY mode and the lamp is switched off. Press and hold for three seconds either of the following:
●The POWER button on the control panel
●The ON button on the remote control
The power indicator on the control panel ashes blue for a few seconds whilst the lamp comes up to full brightness. When the projector is
fully switched on and ready for use, the power indicator switches off.
Switching the projector off
1. Press POWER on the control panel or the POWER button on the remote control, then press the button again to conrm.
The lamp will switch off, the power indicator on the control panel will start ashing in blue and the projector will be in STANDBY mode
while cooling off.
2. Wait until the power indicator has stopped ashing and the fans have stopped working, then disconnect the power cable.
Notes
For full details of how to use the
controls and the menu system, see
the Operating Guide.
Even if the power indicator has
stopped ashing, please allow
the lamp to cool off for ve
minutes before:
●disconnecting the power
●moving the projector
●changing the lamp
Inst-07

Digital Projection M-Vision Cine 400 3D series OPERATING THE PROJECTOR Installation and Quick-Start Guide
Revision C, July 2014
Adjusting the lens
Zoom
Turn the smooth ring on the lens, closest to the case, to adjust the zoom so that the image lls the screen.
Focus
Turn the knurled ring at the outer end of the lens, to adjust the focus until the image is sharp.
Shift
1. To reveal the adjustment access holes, slide the Digital Projection badge in the direction shown below, then gently lift it off by hand.
2. Use the 5mm Allen wrench to adjust the horizontal and vertical position of the image.
Notes
Do NOT prise off the badge
using a tool.
Lens shift controls are not available
on projectors tted with the xed
0.73:1 lens.
Inst-08
Horizontal shift Vertical shift

Digital Projection M-Vision Cine 400 3D series OPERATING THE PROJECTOR Installation and Quick-Start Guide
Revision C, July 2014
Selecting an input signal or test pattern
Input signal
Connect an image source to the projector. The signal should be automatically detected by the projector, and should be displayed within
two or three seconds.
If more than one signal is connected, select the image you want to display in one of the following ways:
●Access the Main menu (either from the remote control or from the control panel) and then go to Input Select.
●On the remote control, select from the inputs using the number buttons 1to 6
●On the control panel, press SOURCE to cycle through all the inputs.
Test pattern
If you have no image source connected to the projector, you can display a test pattern instead. To display a test pattern, do either of the
following:
●Press the TEST button TEST on the remote control to cycle through all test patterns.
●Access the Service menu and select a test pattern.
Notes
For full details of how to use the
controls and the menu system,
see the Operating Guide.
Inst-09

Digital Projection M-Vision Cine 400 3D series OPERATING THE PROJECTOR Installation and Quick-Start Guide
Revision C, July 2014
Adjusting the image
Orientation
To change the image orientation, access the System menu and then open the Rear Projection and Ceiling Mode settings.
Aspect ratio
To set up an aspect ratio for your image, do either of the following:
●Press the ASPECT RATIO button on the remote control to cycle through the available settings.
●Access the Main menu and then select the Aspect Ratio setting.
Picture
To change brightness and contrast, do either of the following:
●Press BRIGHTNESS or CONTRAST on the remote control, then use the arrow buttons to move the sliders.
●Access the Image menu and adjust the Brightness and Contrast settings.
3D
In the Main menu, use the 3D Control sub-menu.
Notes
For full details of how to use the
controls and the menu system,
see the Operating Guide.
Inst-10

M-Vision Cine 400 3D series
High Brightness Digital Video Projector
16:9 widescreen display
Revision C, July 2014 112-855C
CONNECTION GUIDE

Digital Projection M-Vision Cine 400 3D series Connection Guide
Revision C, July 2014
CONTENTS
Important information ............................................................Con-01
Symbols used in this guide.............................................................................Con-01
Special formatting............................................................................................Con-01
Product revision...............................................................................................Con-01
Signal inputs...........................................................................Con-02
Component 1 and 2..........................................................................................Con-02
RGsB....................................................................................................... Con-02
YPbPr/YCbCr.......................................................................................... Con-02
RGB ...................................................................................................................Con-02
HDMI 1 and 2.....................................................................................................Con-02
Supported signal input modes..............................................Con-03
Control connections...............................................................Con-06
Service port.......................................................................................................Con-06
LAN and RS232.................................................................................................Con-06
Wired remote control .......................................................................................Con-06
Trigger 1 and 2 outputs....................................................................................Con-06
3D Sync .............................................................................................................Con-06
LAN IP conguration utility ...................................................Con-07
Wiring details ..........................................................................Con-08
Signal inputs.....................................................................................................Con-08
Component 1........................................................................................... Con-08
Component 2........................................................................................... Con-08
RGB input................................................................................................ Con-08
HDMI inputs ............................................................................................ Con-09
Control connections ........................................................................................Con-10
Wired remote control connection ............................................................ Con-10
Serial control input .................................................................................. Con-10
Trigger 1 & 2 outputs............................................................................... Con-10
LAN connection....................................................................................... Con-11
3D sync connection................................................................................. Con-11

Digital Projection M-Vision Cine 400 3D series IMPORTANT INFORMATION Connection Guide
Revision C, July 2014 Con-01
Important information
Symbols used in this guide
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
FURTHER INFORMATION
This symbol shows important additional information.
Special formatting
●Buttons on the projector control panel or the remote control appear in BLOCK CAPITALS, e.g. MENU. Where necessary, the name of a button is followed by an image, e.g. ON .
●Menu titles and menu items appear in Bold, e.g. the System menu.
●If the described state of the equipment is named, the state appears in CAPITALS, e.g. STANDBY mode.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features without prior notice.

Digital Projection M-Vision Cine 400 3D series SIGNAL INPUTS Connection Guide
Revision C, July 2014
Signal inputs
Component 1 and 2
RGsB
In the Advanced Image menu, set Colorspace to Auto, or if necessary to
RGB Video.
YPbPr/YCbCr
In the Advanced Image menu, set Colorspace to Auto, or if necessary to
REC709 or REC601.
RGB
In the Advanced Image menu, set Colorspace to Auto, or if necessary to
RGB PC.
HDMI 1 and 2
If you are using a Dual Pipe 3D signal, connect the left signal to one input
and the right signal to the other.
If necessary, the images can be swapped using the 3D Settings sub-menu
of the Main menu.
Notes
For a complete listing of pin
congurations for all signal and
control connectors, see Wiring
Details later in this guide.
The projector does not support
RGBS.
Con-02
RGB
Component 1
Component 2HDMI 2HDMI 1

Digital Projection M-Vision Cine 400 3D series SUPPORTED SIGNAL INPUT MODES Connection Guide
Revision C, July 2014
Supported signal input modes
Signal Resolution Frame Rate
(Hz)
3D Support
Component
VGA RGBHV
VGA YUV
HDMI RGB
HDMI YUV 8 bit
HDMI YUV 10 bit HDMI YUV 12 bit
Frame
Packing
Side by Side
(Horizontal)
Top and
Bottom
PC
640 x 480 59.94  
640 x 480 74.99  
640 x 480 85  
800 x 600 60.32  
800 x 600 75  
800 x 600 85.06  
848 x 480 47.95  
848 x 480 59.94  
1024 x 768 60  
1024 x 768 75.03  
1024 x 768 85.03  
1024 x 768 70.1  
1280 x 720 47.95  
1280 x 768 60  
1280 x 768 60  
1280 x 768 75  
1280 x 768 85  
1280 x 800 50  
1280 x 800 60  
1280 x 800 75  
1280 x 1024 60.02  
1280 x 1024 75.02  
1280 x 1024 85.02  
1440 x 900 60  
Con-03
continued on next page...

Digital Projection M-Vision Cine 400 3D series SUPPORTED SIGNAL INPUT MODES Connection Guide
Revision C, July 2014
Signal Resolution Frame Rate
(Hz)
3D Support
Component
VGA RGBHV
VGA YUV
HDMI RGB
HDMI YUV 8 bit
HDMI YUV 10 bit HDMI YUV 12 bit
Frame
Packing
Side by Side
(Horizontal)
Top and
Bottom
PC (continued)
1440 x 900 75  
1400 x 1050 60  
1400 x 1050 75  
1600 x 1200 60  
1920 x 1080 47.95  
1600 x 1200 60  
1920 x 1200 60  
1680 x 1050 59.94  
Apple Mac
640 x 480 66.59  
832 x 624 74.54  
480i 59.94  
576i 50  
EDTV 480p 59.94       
576p 50       
Con-04
continued on next page...