Digital Projection POWER 2v User manual

The POWER display range of
SUPER-HIGH-BRIGHTNESS DIGITAL VIDEO PROJECTORS
POWER 2v, POWER 4dv and POWER 5dv
USER MANUAL
Revision E - 28/01/98

Directives covered by this Declaration
89/336/EEC Electromagnetic Compatibility Directive, amended by 92/31/EEC & 93/68/EEC
73/23/EEC Low Voltage Equipment Directive, amended by 93/68/EEC
Products covered by this Directive
Large Screen Projector types POWER 2v,POWER 4dv and POWER 5dv
Basis on which Conformity is being declared
The products identified above comply with the protection requirements of the above EU
directives, and the manufacturer has applied the following standards:-
BS EN 50081-1: 1992 EMC Generic Emission Standard for Residential, Commercial and
Light Industrial Equipment.
BS EN 50082-1: 1992 EMC Generic Immunity Standard for Residential, Commercial and
Light Industrial Equipment.
BS EN 55022: 1995 - Limits and Methods of Measurements of Radio Disturbance
Characteristics Information Technology Equipment.
BS EN 60950: 1992 - Specification for Safety of Information Technology Equipment, includ-
ing Electrical Business Equipment.
The technical documentation required to demonstrate that the products meet the requirements
of the Low Voltage Directive has been compiled by the signatory below and is available for
inspection by the relevant enforcement authorities. The CE mark was first applied in 1997.
Signed:
Authority: D.J. Quinn, Product Development Director
Date: 29th April 1997
Attention!
The attention of the specifier, purchaser, installer, or user is drawn to special measures and
limitations to use which must be observed when these products are taken into service to
maintain compliance with the above directives. Details of these special measures are
available on request, and are also contained in the product manuals.
Declaration of Conformity
LBV00018; Revision E - 28/01/98

From time to time revisions will be issued to this manual. To maintain a correct and
up to date copy of the manual it is important that the instructions given in revision
notices are carried out.
The person carrying out the revision should complete the table below.
Revision No Revision Details Date Revised
Revision Record
LBV00018; Revision E - 28/01/98

Please read the following before proceeding
The Digital Projection POWER displays are Super-High-Brightness Video Projectors
capable of producing images of superb brightness and clarity with the minimum of
set-up time and operating support. The User Interface via the On Screen Display, is
designed to allow the novice user rapid access to basic projector operation while
providing the expert with the ability to tailor the performance to his exact
requirements.
An Outline of Contents is given overleaf which provides an overview of the five
sections, A to E, in this manual and lists all the major topics covered along with
their location. This outline allows the user to direct themselves to the appropriate
section of this manual where a detailed contents page will provide the exact location
of the topic required. Section identifiers are also provided on the outside edge of the
pages to allow the quick location of individual sections.
The user is strongly recommended to read Section A: Overview before unpacking
or switching on the projector, paying particular attention to the safety warnings on
pages A—3 and A—4.
Disclaimer Digital Projection makes a sincere effort to ensure accuracy and quality of it's published materials;
however, no warranty, expressed or implied, is provided. Digital Projection disclaims any direct or indirect damages
resulting from the use of any information in this manual.
Introduction
Introduction
INTRODUCTION
LBV00018; Revision E - 28/01/98

Digital Projection Limited,
Greenside Way, Middleton, Manchester M24 1XX, UK.
Registered in England No. 2207264, Registered Office: As Above
Tel: [phone]
Fax: [phone]
E-Mail: [email protected]
Web Site: www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115, Kennesaw, GA 30144. USA
Tel: (USA) 770 420 1350
Fax: (USA) 770 420 1360
E-Mail: [email protected]
Web Site: www.digitalprojection.com
DMD and Digital Micromirror Device are trademarks of Texas Instruments Incorporated.
Introduction
INTRODUCTION
LBV00018; Revision E - 28/01/98

Section A: Overview
Packaging....................................................................AÑ1
Safety Advice...............................................................AÑ2
Initial Preparation ........................................................AÑ5
Components.................................................................AÑ8
Section B: System Installation
Installation Guidelines ..................................................BÑ1
Switching On...............................................................BÑ17
Section C: System Operation
Remote Control - Overview..........................................CÑ1
LED Indicators...............................................................CÑ6
Menu Operation...........................................................CÑ7
Main Menu - Overview ..............................................CÑ11
Channel Set-up Function ...........................................CÑ13
Image Mode...............................................................CÑ28
User Preferences .........................................................CÑ29
Test Patterns ...............................................................CÑ31
Projector Status ...........................................................CÑ33
Set Projector Address..................................................CÑ35
Add Computer ...........................................................CÑ36
Applying a New Signal Source..................................CÑ42
Adjusting the Displayed Image .................................CÑ45
Addressing Multiple Projectors...................................CÑ48
Introduction
Outline of Contents
INTRODUCTION
LBV00018; Revision E - 28/01/98

Section C: System Operation
Computer Control.......................................................CÑ49
Switcher Operation.....................................................CÑ54
Section D: Advanced User Information
Screen Illuminance ......................................................DÑ1
DMDª Operation and Usage ......................................DÑ2
Operation Flowcharts...................................................DÑ4
Lenses .........................................................................DÑ14
Technical Specification ..............................................DÑ44
Section E: Fault Finding & Maintenance
Trouble Shooting ...........................................................EÑ1
Maintenance ................................................................EÑ4
Appendix
Quick Set-up Reference.......................................................i
Menu System Review ........................................................iii
Glossary.............................................................................vi
Introduction
INTRODUCTION
LBV00018; Revision E - 28/01/98

Packaging .........................................................................AÑ1
Projector Packaging.....................................................AÑ1
Lens Packaging ...........................................................AÑ1
Safety Advice ....................................................................AÑ2
Compliance with Regulatory Bodies ...........................AÑ2
Safety Warnings...........................................................AÑ3
Initial Preparation .............................................................AÑ5
Pre-Installation Check ..................................................AÑ5
Remote Control Unit - Battery Installation ...................AÑ6
Remote Receiver..........................................................AÑ7
Components ......................................................................AÑ8
Projector Case ..............................................................AÑ8
LED Indicators ..............................................................AÑ9
Arc Lamp .....................................................................AÑ9
Optics .........................................................................AÑ10
Lenses.........................................................................AÑ10
Electronics ..................................................................AÑ11
Digital Micromirror Devicesª ....................................AÑ11
Analogue Input Board ...............................................AÑ12
Power Supplies ...........................................................AÑ13
Cooling System ..........................................................AÑ13
Air Filters.....................................................................AÑ14
Overview
Section A: Overview
OVERVIEW
LBV00018; Revision E - 28/01/98

Components
Remote Control ..........................................................AÑ14
Remote Receiver ........................................................AÑ15
Overview
OVERVIEW
LBV00018; Revision E - 28/01/98