Digital Watchdog MEGApix DWC-MD44WA User manual

DWC-MD44WAB DWC-MD44WiAB
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 3 – INSTALLING THE CAMERA
STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
1. The mounting surface must bear ve times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover
to be damaged. This may cause a breakdown or re.
3. For the installation process, remove the dome
cover from the camera module. Press on the
camera dome from both sides to separate from
the camera module.
4. Using the mounting template sheet or the
camera itself, mark and drill the necessary holes
in the wall or ceiling.
6. Use the camera’s 3-Axis gimbal to adjust the camera’s tilt and angle.
The camera’s maximum tilting angle is 75°.
7. Secure the dome cover over the camera by snapping is back into place.
Detach the protecting lm from the dome bubble.
5. Pass the wires through the mount bracket and make all necessary
connections.
a. NETWORK CONNECTIONS – If you are using a PoE Switch, connect the
camera using an Ethernet cable for both data and power.
b. NETWORK CONNECTIONS – If you are using a non-PoE switch, connect
the camera to the switch using an Ethernet cable for data transmission
and use a power adapter to power the camera.
Power Requirements
DC 12V
PoE IEEE 802.3af / PoE Class 3
Power Consumption
IR Models:
Auto Focus Working MAX 7.8W
LED Off: 3.6W
LED On: 5.2W (IR Models)
Non-IR Models:
Auto Focus Working MAX 6.2W
AF Off: 3.6W POWER
NETWORK
CONNECTION
Resetting the camera: To reset the camera, use the tip of a paper clip
or a pencil and press the reset button. Pressing the button for ve (5)
seconds will initiate a camera-wide reset of all the settings, including
network settings.
DWC-MD44WA DWC-MD44WiA
1
2
5
4
Template
Sheet
3
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
NOTE: Download All Your Support Materials and Tools in One Place
1. Go to: http://www.digital-watchdog.com/support-download/
2. Search your product by entering the part number in the ‘Search by Product’ search
bar. Results for applicable part numbers will populate automatically based on the
part number you enter.
3. Click ‘Search’. All supported materials, including manuals, Quick Start Guides
(QSG), software and rmware will appear in the results.
Attention: This document is intended to serve as a quick reference for initial
set-up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
Quick Start GuideQuick Start Guide
Default Login Information
Username: admin Password: admin
WHAT’S IN THE BOX
QSG Manual 1 Set Template Sheet 1 Set
Test Monitor
Cable 1 Set Screw & Plastic Anchor – 2pcs 1 Set
NOTE: DO NOT remove the IR rubber ring.
It will cause IR reection issues.
DO NOT remove
the IR rubber ring
During installation,
DO NOT touch the
dome cover without the
protection lm included
in box as an accessory.
NOTE: When the installation is complete, please remove the IR protective
foam before applying the camera’s dome.
Reset
Button

STEP 4 – CABLING
Use the diagram below to properly connect power, network, audio, alarm and
sensors to the camera.
NETWORK
CONNECTION
AUDIO
INPUT
AUDIO
OUTPUT
POWER RELAY / ALARM
OUTPUT
SENSOR / ALARM
INPUT
Quick Start Guide
NOTE: Please see the full product manual for web viewer setup,
functions and camera settings options.
7. To view the camera’s web viewer, click on ‘View Camera Website’.
8. To save the changes made to the camera’s settings, input the ID and PW of
the camera for authentication and click ‘Save’.
9. If the camera needs to be rebooted after the settings were changed, press
the ‘Reboot’ button. The camera will cycle power and will appear back in the
search results once the reboot is complete.
6. The camera’s default network
information is:
STEP 5 – DW IP FINDER™
Use the DW IP Finder™software to scan the network and detect all MEGApix®
cameras, set the camera’s network settings or access the camera’s web client.
Rev Date: 02/17
Copyright © Digital Watchdog. All rights reserved.
Specications and pricing are subject to change without notice.
Select DHCP if the internet service is dynamic IP. This will allow the camera to
receive its IP address from the DHCP server.
Select STATIC to manually enter the camera’s IP address, subnet mask,
Gateway and DNS information.
Contact your network administrator for more information.
Default TCP/IP information
• IP: DHCP
‘Port Forwarding’ has to be set in your network’s router for external access
to the camera.
Default ID / PW : admin / admin
Network Setup
1. Go to: http://www.digital-watchdog.com
2. Search for ‘IP Finder’ on the quick search bar at the top of the page.
3. The latest IP Finder software will appear in the search results. Click on the
link to download the le to your computer.
4. The software will scan your network for all supported cameras and display
the results in the table. Allow up to 5 seconds for the IP Finder to nd the
camera on the network.
5. Select a camera from the list by double-clicking on the camera’s image
or clicking on the ‘Click’ button under the IP Conf. column. The camera’s
network information will appear. If necessary, you can adjust the camera’s
network type.
Search for Cameras
Camera’s
Network Settings
View Camera’s
Thumbnail View
Camera’s Firmware
Camera Uptime
Open Camera’s IP
Conguration Screen
Filter Search Results
Camera Name,
Model, IP Address,
and MAC Address
Firmware Upgrade
STEP 6 – WEB VIEWER
*
The GUI display may differ by camera models.
NOTE: The camera’s maximum tilting angle is 75°.
NOTE: Some Menu options may not be available based on the camera
model. See the full manual for more information.
*
Once the camera’s network settings have been setup properly, you can access
the camera’s web viewer using the DW IP Finder™.
To open the camera’s web viewer:
1. Find the camera using the DW IP Finder™.
2. Double-click on the camera’s view in the results table.
3. Press the ‘View Camera Website’. The camera’s web viewer will open up
in your default web browser.
4. Enter the camera’s username and password (default are admin / admin).
5. If you are accessing the camera for the rst time, install the VLC player for
web les in order to view video from the camera.