Digitus USB 3.0 Dual SATA HDD User manual

USB 3.0 DUAL SATA HDD
DOCKING STATION
User Manual
(DA-70547)

Introduction
DA-70547 is a USB3.0 enabled dual-SATA hard drive enclosure. It supports
simultaneously use of two 2.5” or 3.5” SATA hard disk for both data read and data
write. It also is downward compatible with USB2.0 and USB1.1. The maximum
transfer speed of USB3.0 can reach 5Gbps. The actual transfer speed of DA-70547 is
200M/s. DA-70547 provides high storage capacity, high data transfer rate, and best
data protection. It’s easy to use the design which can satisfy both regular users and
professionals of the ever-increasing demand for large and efficient data storage
media.
Function
Support USB3.0 SUPERSPEED mode max 5Gbps/ USB2.0 HIGH-SPEED mode
480Mbps/USB1.1 FULL-SPEED 12Mbps
Support SATA I (1.5G) / SATA (3G) HDD
Achieves transfer speeds of up to 200MB/s
Downwards compatible with any USB2.0 enabled computers and notebooks
Easy to Install and Set-up
To achieve USB3.0 transfer speeds, a USB3.0 interface card with USB3.0 cable is
required
Supported OS: Windows 7 (32/64-bit), Vista (32/64-bit), XP(32/64-bit)
One Touch Back-Up function
User’s Manual
Notice
The type of file system is able to support FAT32 and NTFS both..
When users operate the PC Clone EX Lite, the login must be from Administrator; it
can not login from the Guest or any authorized account.
Does the hard disk happen to the bad sector? Please confirm in advance that can
prevent an improper operating of backup or restore.
System Requirements
Pentium computers or 100% compatible computers.
Support OS: Microsoft Windows 98SE/ME/200/XP/Vista/7.
CPU Pentium or above
128 MB RAM
Display card: compatible with VESA standard
An external USB hard disk

Software installation
1. Please put PCClone EX Lite CD into CD ROM drive, the program directly goes on the
screen of PCClone Setup Wizard. (In case the screen doesn’t come out, please
operate the window box of “setup.exe”)
2. Click “install’.
3. Please read the license agreement in detail
4. If users accept the agreement, please click “Next” to install
5. Click “Install” to next

6. The installation is completed, please click “OK” to exit.
7. “PCClone EX”icon will displays in the notification area after setup; users can
double-click the icon or press the right key of the mouse to execute PCClone EX Lite.

Create Partition
If your USB HDD has managed already, please skip this part and move on next context.
Steps
1. Please plug USB HDD. (Turn on the USB power)
2. Please right click “My computer”, and point “Manage”. (If also can click in succession
as “Start”→“Control Panel”→“Administrative Tools”→“Computer Management” (If
your USB HDD has managed already, please skip this part and move on next context)

3. Please click “Disk Management” as the left window, and then find the disk
management as the right window.
4. Please right click the disk of “Unallocated”, and point the “New Partition”. (In order to
make sure the disk of “Unallocated” whether the USB disk uses this area or not, users
can find out by removing and plugging the port of USB connection)
5. Follow up the installation of “Partition Wizard” to operate the disk of partition and
format

6. Also, you can format USB hard disk by “FNet FAT32 Utility” and then you can start the
backup function (The detail format steps please refer to the section of “FNet FAT32
Utility”)
FAT32 Format Utility
For the current HDD capacity is getting larger, the Fat32 Format Utility in Windows
2000/XP is not able to support the HDD size exceeding 32GB; FNet recommends FNet
Fat 32 Format Utility, which can format the large capacity to be FAT32 Format rapidly and
fully, the size even maximums up to 4TB (4000GB)
(Attention: all data in USB HDD will be deleted if you use this function)
1. Please plug USB HDD, and turn on the computer
2. Click “Start ” →“All Programs” →“PCClone EX” →“FNet FAT32 Format”

3. Confirm the “USB Device’ and “Drive to Format ” in the FAT32 Format Utility, and then
press “Start”
4. Tick “Quick Format” and click “Start” for executing
(Attention: All data in USB HDD will be deleted if you use this function)

5. The window shows in progress

One Button File Backup
One Button backup function only supports the external HDD case with button design –
It won’t set comprehensive steps for backup anymore, only use the button of the
external HDD case. Note: when you click the button of backup, the icon of PCClone
EX Lite must be staying at the notification area. (For first time using, please refer to
the context of “File backup” and “Setup”)
The USB driver of Win 98SE/ME to the button trigger support has not unified,
therefore, this support in Win98SE/ME does not definite exactly, Please refer the
original user manual of the computer.
1. Please plug USB HDD. (Turn on USB power)
2. Execute PCClone EX Lite.
3. Just press the button on the external case. (If the external device has double
buttons, please click the “File” one)
4. A dialog window will jump out of confirming the File backup or users can click “Start’
by the mouse.