Digitus DN-95347-1 User manual

16 Port Gigabit PoE Switch,
19 Inch, Unmanaged,
2 SFP Uplink
Quick Installation Guide
DN-95347-1

2
1. Introduction
The DIGITUS 16-Port Gigabit Rack mount Switch with sixteen Power over Ethernet ports
and two additional SFP Fiber Port, offers your network significant improvement in
terms of performance and efficiency. Thanks to PoE support, you only need a single
(network) cable for power and data transfer. This switch makes it much easier to
connect devices such as access points, network cameras, and IP telephones, and
requires far less cabling than alternatives. It also allows you to extend your network in
places where there are no power supply cables or sockets available. The switch does
not require any configuration and therefore guarantees quick and seamless integration
into the network. Moreover, can be manually switched to a Normal mode, or Flow
Control mode, or VLAN mode to suitable for various occasions flexibly. Based on Gigabit
Ethernet Technology, it is essential to helping solve network bottlenecks that frequently
develop as more advanced computer users and newer applications continue to demand
greater network resources.
2. Features
Comply with IEEE 802.3i, IEEE 802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3x,
IEEE802.3az standards
Support IEEE802.3af, IEEE802.3at standards
Supporting Normal mode, VLAN mode and Extend mode, flexible to switch
The maximum output power of a single port is 30W, and the total output power of
PoE is 247W.
16 x 10/100 /1000 Mbps self-adaptive RJ45 ports, support port auto flip (Auto MDI /
MDIX)
Flow control method: Full-duplex adopts IEEE 802.3x standard, half-duplex adopts
Backpressure standard.
Support MAC address self-learning
The UTP port supports the auto-negotiation function and automatically adjusts the
transmission mode and transmission rate
Use store-and-forward architecture
3. Package Contents
1x 16 Port Gigabit PoE Switch, 19 Inch,
Unmanaged, 2 SFP Uplink
1x Power Cable
1x QIG

3
4. Specifications
Interfaces
16*10/100/1000Mbps Adaptive Ethernet port
2*100/1000Mbps SFP port
SFP port
Support 1000Base-X
Working Mode
Normal mode
（Switch all ports can communicate with each other）
Flow Control mode
(All ports' flow control functions are disable)
VLAN mode (1 to 16 cannot communicate with each
other, but can communicate with 17F-18F)
Power Supply
AC (AC) Input:
Rated voltage range: 100-240V~
Maximum voltage range: 90-264V~
Frequency: 50 -60 hz
Rated current: 3.5A
PoE
Support IEEE 802.3AF and IEEE 802.3AT
Single port PoE maximum output power 30W,
The whole machine support PoE maximum output
power 247W.
The output voltage of PoE power supply port is 54V.
Power Pin Assignment
1/2(+),3/6(-)
Power Consumption
Maximum (PoE on): 297W
Operating Temperature
0ºC ~ 45ºC
Storage Temperature
-40ºC ~ 70ºC
Operating Humidity
10% ~ 90% RH
Storage humidity
5% ~ 90% RH
Fan
Support
Dimensions (W x D x H)
440*208*44mm
Switching Capacity
36Gbps

4
5. External Component Description
The front panel consists of 16*10/100/1000Mbps Adaptive Ethernet port, 2*1000Mbps
SFP port, 1*Mode switch, a series of LED indicators. The rear panel provides an AC power
connector, a Ground Terminal. Its appearance is shown below:
Front Panel
The front panel consists of LED indications and network ports.
1
PWR indicator
2
10/100/1000Base-T Link/Act indicator
3
Mode switch
4
10/100/1000Base-T Adaptive Ethernet port
5
SFP port
Real Panel
The rear panel view of the Switch consists of an AC power connector.
1
Ground Terminal
2
AC power connector
Power Supply
Rated voltage range: 100-240V~
Frequency: 50 to 60 Hz

5
Cooling Solution
The switch adopts turbo fan for ventilation to ensure that the equipment can work
normally under the specified environment. When placing the case, leave enough space of
10cm on both sides of the case and the rear panel to facilitate air circulation.
PD power supply wiring
The PoE power supply design supports the iEEE802.3af and 802.3at power supply
standards, and uses Alternative a mode power supply, that is, 12+, 36- power supply in
the standard Ethernet port.
Indicator
Indicator
Faceplate
Marker
Status
Indication
PWR Status
Light
PWR
Off
Power Off.
Solid green
Power On.
Ethernet port
indicator
Link/ACT
(1-16)
Off
The port is NOT connected.
Solid orange
The port is connected at
10/100Mbps.
Blinking
The port 10/100M data transceiver.
Solid green
The port is connected at
1000Mbps.
Blinking
The port 1000M data transceiver.
SFP port
indicator
Link/ACT
(17F-18F)
Off
The port is NOT connected.
Solid orange
The port is connected at 100Mbps.
Blinking
The port 100M data transceiver.
Solid green
The port is connected at
1000Mbps.
Blinking
The port 1000M data transceiver.
PoE status
indicators
PoE
(1-16)
Off
The port PoE is not powered.
Solid green
Power supply to port PoE normal.
Blinking
The port PoE overloaded

6
6. Installing and Connecting the Switch
This part describes how to install your Ethernet Switch and make connections to it.
Please read the following topics and perform the procedures in the order being
presented.
6.1 Installation
Please follow the following instructions in avoid of incorrect installation causing device
damage and security threat.
Put the Switch on stable place or desktop in case of falling damage.
Make sure the Switch works in the proper AC input range and matches the voltage
labeled on the Switch.
To keep the Switch free from lightning, do not open the Switch's shell even in power
failure.
Make sure that there is proper heat dissipation from and adequate ventilation around
the Switch.
Make sure the cabinet to enough back up the weight of the Switch and its
accessories.
6.1.1 Desktop Installation
Sometimes users are not equipped with the 19-inch standard cabinet. When installing
the Switch on a desktop, please attach these cushioning rubber feet provided on the
bottom at each corner of the Switch in case of the external vibration. Allow adequate
space for ventilation between the device and the objects around it.
6.1.2 Rack-mountable Installation in 19-inch Cabinet
The Switch can be mounted in an EIA standard-sized, 19-inch rack, which can be placed in
a wiring closet with other equipment. To install the Switch, please follow these steps:
1) Attach the mounting brackets on the Switch's side panels (one on each side) and
secure them with the screws provided.

7
2) Use the screws provided with the equipment rack to mount the Switch on the rack
and tighten it.
6.1.3 Power on the Switch
The Switch is powered on by the AC 100-240V 50/60Hz internal high-performance power
supply. Please follow the next tips to connect:
AC Electrical Outlet:
It is recommended to use single-phase three-wire receptacle with neutral outlet or
multifunctional computer professional receptacle. Please make sure to connect the metal
ground connector to the grounding source on the outlet.
AC Power Cord Connection:
Connect the AC power connector in the back panel of the Switch to external receptacle
with the included power cord, and check the power indicator is ON or not. When it is ON,
it indicates the power connection is OK.
6.2 Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing network card driver, please
connect one end of the twisted pair to RJ-45 jack of your computer, the other end will be
connected to any RJ-45 port of the Switch, the distance between Switch and computer is
around 100 meters. Once the connection is OK and the devices are power on normally,
the LINK status indicator lights corresponding ports of the Switch.
6.3 Switch connection to the PD
1-16 ports of the Switch have PoE power supply function, the maximum output power up
to 30W each port, it can make PD devices, such as internet phone, network camera,
wireless access point work. You only need to connect the Switch PoE port directly
connected to the PD port by network cable.

8
CE Mark Warning: This is a Class A product. In home environment, this product may cause
radio interference. In this case, the user may be required to take appropriate measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of
the shipping content. If the Declaration of Conformity is missing, you can request it by
post under the below mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3, 58513 Lüdenscheid, Germany