Dimplex DHCER20FE User manual

– 1 –
FLAME EFFECT
CERAMIC HEATER
INSTRUCTION MANUAL
DHCER20FE
Please read the instructions carefully before use.
Keep manual for future reference.
This product is only suitable for well insulated spaces or occasional use.
14064_DHCER20FE Manual_V2.indd 1 7/12/17 4:25 PM

– 2 –
CONTENTS
Safety Warning and Notices 2
Product Features 4
Components Description 4
Product Operation Introduction 6
Maintenance and Cleaning 8
Technical Parameters 9
Warranty 9
SAFETY WARNING AND NOTICES
Please pay close attention to the warnings and instructions in this manual for correct
operation and to avoid any danger caused by incorrect use.
1. This appliance can only be used by children 8 years and above and people
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning the use of
the appliance in a safe way and understand the hazards involved. Children should
not play with the appliance.
2. CAUTION — Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are
present.
3. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid any hazards.
4. WARNING: In order to avoid overheating, do not cover the heater.
5. The heater must not be placed immediately below a socket outlet.
6. Do not use this heater in the immediate surroundings of a bath, shower or a
swimming pool.
7. The fan heater can only be used under supervision.
8. The air inlet/outlet area must never be covered. Keep a distance of at least
1m in front and 50cm behind the fan.
9. If there is any indication of a malfunction, contact service center repairs.
Do not attempt to disassemble the product or replace faulty parts with
unauthorized components because it will damage the unit.
14064_DHCER20FE Manual_V2.indd 2 7/12/17 4:25 PM

– 3 –
10. Do not disassemble or make changes to the product unless you are authorized by
the dealer or producer.
11. Do not touch the plug with wet hands, it may lead to electric shock.
12. Do not put foreign objects into the air inlet or outlet.
13. Do not use pesticide or other flammable sprays around the product.
14. Make sure the fan doesn’t blow heated air directly at small children for long periods
of time.
15. Do not pull out the power plug by pulling the power cord, it may cause damage to
the power cord and cause an electric shock.
16. Make sure the power cord is undamaged, and the plug is correctly plugged into the
wall socket.
17. If there is an abnormal smell or noise when the product is in use, turn off the
product and pull out the power cord immediately.
18. Do not operate the appliance with a damaged power cord or plug. Send the heater
to a suitably qualified or appointed service agent for inspection and repair.
19. Make sure not to fold the power cord or place heavy objects on the power cord, it
may lead to electric shock.
20. If the heater will not be used for a long period of time, disconnect the plug.
21. Use a power outlet that meets the inspection requirements where the carrying
capacity of the socket is no less than 10A/230V.
22. Ensure the power supply voltage is consistent with the specified voltage in the
machine (220-240VAC).
23. Do not use the device directly below a power outlet.
24. When using the heater, keep combustible materials or explosive objectives, away
from the heater.
25. In order to avoid overheating, do not cover the heater.
26. Never place any objects inside the device.
14064_DHCER20FE Manual_V2.indd 3 7/12/17 4:25 PM

– 4 –
PRODUCT FEATURES
1. PTC ceramic heating element, changes the power automatically according to the
variation in the ambient temperature.
2. Optional high or low power.
3. Set timer has a range between 1-24 hours.
4. Temperature setting of 15ºC to 35ºC.
5. Uses a DC fan, which increases efficiency and has low operational noise.
6. Tip-over safety protection, double over-heating protection (Thermistor, temperature
fuse) for safer use.
7. Convenient operation with an infrared remote control function.
8. Oscillating, swing function.
9. LED display will automatically dim after 1 minute during operation, to save energy
and power.
10. Optional Flame effect.
COMPONENTS DESCRIPTION
PRODUCT STRUCTURE
1. Front cover
2. Wind outlet
3. Flame effect display window
4. Swing holder
5. Base
6. Power cord
7. Control panel
8. Power switch
9. Remote control
Page 4
materials or explosive objectives, away
from the heater.
28. In order to avoid overheating, do not cover the
heater.
29. Never place any objects inside the device.
Product features
1. PTC ceramic heating element, changes the power automatically according to the
variation in the ambient temperature.
2. Optional high or low power.
3. Set timer has a range between 1-24 hours.
4. Temperature setting of 150 to 350.
5. Uses a DC fan, which increases efficiency and has low operational noise.
6. Tip-over safety protection, double over-heating protection (Thermistor, temperature
fuse) for safer use.
7. Convenient operation with an infrared remote control function.
8. Oscillating, swing function.
9. LED display will automatically dim after 1 minute during operation, to save
energy and power.
10. Optional Flame effect
Components Description
Product structure
1. Front cover
2. Wind outlet
3. Flame effect display window
4. Swing holder
5. Base
6. Power cord
7. Control panel
8. Power switch
9. Remote control
14064_DHCER20FE Manual_V2.indd 4 7/12/17 4:25 PM

– 5 –
Page 5
Control panel
Display panel
Remote control operation panel
Page 5
Control panel
Display panel
Remote control operation panel
Page 5
Control panel
Display panel
Remote control operation panel
CONTROL PANEL
DISPLAY PANEL
REMOTE CONTROL
OPERATION PANEL
FLAME EFFECT
TURN ON/OFF
FLAME EFFECT
FLAME EFFECT
POWER BUTTON
POWER BUTTON
POWER BUTTON
SET TEMPERATURE
SET TIMER (IN NO. OF HOURS)
LOW HEAT SETTING
ACTIVATED
HIGH HEAT SETTING ACTIVATED
TURN ON/OFF ECO MODE
ECO MODE
CHANGE HEAT
SETTINGS
TIMER + (UP) BUTTON
TIMER + (DOWN) BUTTON
MODE BUTTON (HI/LOW/ECO)
TEMP + (UP) BUTTON
TEMP + (DOWN) BUTTON
OSCILLATE BUTTON
OSCILLATING
OSCILLATING
14064_DHCER20FE Manual_V2.indd 5 7/12/17 4:25 PM

– 6 –
PRODUCT OPERATION INTRODUCTION
INSTALLATION METHOD
1. Take the device out of the bubble wrap, including the following three parts; heater,
base and remote control.
2. Put the heater on a flat surface upside-down (with the base facing up). Connect the
base with the heater.
3. Turn the unit right way up.
4. Press Power button which is in the back of the device, to turn on.
REMOTE CONTROL OPERATION PANEL
1. Pull out the battery cover on the back of the remote control.
2. Pay attention to the battery polarity, and insert the battery (CR2032) into the tray of
the panel.
3. Push the battery cover back into the remote control.
Page 6
l
bein
Product Operation introduction
Installation method
1. Take the device out of the bubble wrap, including the following three parts;
heater, base and remote control.
2. Put the heater on a flat surface upside-down (with the base facing up). Connect the
base with the heater.
3. Turn the base right way up.
4. Press Power switch which is in the back of the device to turn on.
Remote control operation panel
1. Pull out the battery cover on the back of the remote control.
2. Pay attention to the battery polarity, and insert the battery (CR2032) into the tray
of the panel.
3. Push the battery cover back into the remote control.
The function of buttons
The fan will operate whenever the heater is heating. If the heater stops working,
then the fan will stop working after 10s.
①After connecting to the power supply and switching on the power, you will hear a
beeping sound, the heater then enters Standby Mode. The power indicator ights up.
②Under standby mode, key to turn on/off the heater. When turning off the
heater, the display panel and fan will then countdown (from 10 to 0 second) before
switching off.
③The default setting after g switched on is:
a) Heater：low power, lights up.
b) Oscillation：off, lights off.
c) Timer：0 hrs, lights off.
d) Fan：turned on.
e) Temperature setting: the default temperature setting is 25℃.
f)
Fireplace display：turned on, lights up.
g) ECO: turned off, lights off.
THE FUNCTION OF BUTTONS
The fan will operate whenever the heater is heating. If the heater stops working, then
the fan will stop working after 10s.
1. After connecting to the power supply and switching on the power, you will hear a
beeping sound, the heater then enters Standby Mode. The power indicator
lights up.
2. Under standby mode, key to turn on/off the heater. When turning off the
heater, the display panel and fan will then countdown (from 10 to 0 second) before
switching off.
3. The default setting after being switched on is:
a) Heater: low power, lights up.
b) Oscillation: off, lights off.
c) Timer: 0 hrs, lights off.
14064_DHCER20FE Manual_V2.indd 6 7/12/17 4:25 PM

– 7 –
d) Fan: turned on.
e) Temperature setting: the default temperature setting is 25ºC.
f) Fireplace display: turned on, lights up.
g) ECO: turned off, lights off.
4. In heating mode, press to shift the power between low and high power level.
a) Low power: lights up.
b) High power: lights up.
5. In heating mode, press to enter ECO mode, lights up, press it again to
quit this mode.
a) ECO mode: the default temperature setting is 22ºC. When the room
temperature is lower than 18ºC, the machine works in high power: when
the room temperature is between 18ºC and 22ºC the machine works in low
power. When the room temperature is above 22ºC the heating element will
turn off.
b) When the ECO function is operating, the button is not active.
c) When the room temperature is above 22ºC the heater and oscillation function
will also be turned off.
6. In heating mode, press to turn on/off the oscillation function, will light
up/off accordingly.
7. In heating mode, press
Page 5
Control panel
Display panel
Remote control operation panel
or
Page 5
Control panel
Display panel
Remote control operation panel
button to set the timer.
a) Timer: press
Page 5
Control panel
Display panel
Remote control operation panel
or
Page 5
Control panel
Display panel
Remote control operation panel
key, and will display, press +/-
key to set the timer (within a range of 0-24 hours), the timer will increase or
decrease by 1hr increments.
b) Entering the timer mode by pressing
Page 5
Control panel
Display panel
Remote control operation panel
or
Page 5
Control panel
Display panel
Remote control operation panel
does not change
the timer settings. But you can set the timer by pressing the +/- key. After no
operation for 5 seconds, the time that you have set will be saved.
c) When the timer turns to the value “0”, the device will then turn off and enter
into standby mode.
d) If the timer is set as “0”, it means that no timer is set.
8. In heating mode, press
Page 5
Control panel
Display panel
Remote control operation panel
or
Page 5
Control panel
Display panel
Remote control operation panel
button to set the temperature.
a) Temperature setting function: press
Page 5
Control panel
Display panel
Remote control operation panel
or
Page 5
Control panel
Display panel
Remote control operation panel
key, and
SETºC will display, press +/- key to set the temperature. The range of the
temperature is from 15°C to 35°C, and can increase or decrease by 1°C
increments.
b) Entering into the temperature settings by pressing
Page 5
Control panel
Display panel
Remote control operation panel
or
Page 5
Control panel
Display panel
Remote control operation panel
keys
does not change the temperature settings. You can set the temperature by
pressing +/- key. After no operation for 5 seconds, the temperature that you
have set will be saved.
14064_DHCER20FE Manual_V2.indd 7 7/12/17 4:25 PM

– 8 –
9. When both the time and temperature are set, the LED display will switch between
showing the set temperature and timer setting every 30 seconds. When a timer is not
set, it will only show the set temperature.
10. When the heater is turned on or in standby mode, press button to turn on/off the
flame effect function, the LED will light up/off accordingly.
11. Memory function in standby mode:
When the heater is turned on (except for the first time), under standby mode, the unit
will revert to the last used setting (except for the timer).
12. After working for 1 minute, the brightness of the LED display will reduce to 1/3 of the
normal brightness. It will resume to the normal brightness when any operation of the
device is activated.
13. If the unit falls over the tip-over switch inside the heater will disconnect the heater
automatically.
14. Remarks:
a) when the over-heat sensor is activated (temperature is above 60ºC),the LED
display will display “EE”, and the heater will turn off.
b) When the environment temperature is lower than -10ºC, the LED will display “LO”
c) When the environment temperature is higher than 40ºC, the LED will display “HI”
MAINTENANCE AND CLEANING
1. Before any cleaning or maintenance, make sure the heater is completely turned off,
and the power cord is not connected to the wall socket.
2. Use a soft cloth to wipe the dust off the heater’s surface; If the surface is very dirty, use
a moist soft cloth to wipe it with water less than 50°C mixed with a neutral detergent.
3. Do not use gasoline, thinner or any other chemicals that can damage the surface.
4. Before storing the heater, let it cool down and store it in a dry and ventilated area.
5. Warning: any other servicing should be performed by an authorized service
representative.
14064_DHCER20FE Manual_V2.indd 8 7/12/17 4:25 PM

– 9 –
TECHNICAL PARAMETERS
Model NO. DHCER20FE
Voltage 220-240V
Frequency 50 Hz
Power 2000 W
Noise level. ≤50 dB
Dimension 260mm x 260mm x 830mm
WARRANTY
This device comes with a 2 year warranty from the date of purchase. Keep your receipt
as proof of purchase date. This guarantee only applies if the item has been used as
intended, and all instructions have been followed accordingly. Please note that this
product is for domestic use only and not for commercial use. Improper use of the
product will invalidate the guarantee. Returned goods can be accepted if repackaged in
the original product box, and presented with the original receipt.
IMPORTANT
Do not dispose this product as unsorted municipal waste, use separate
collection facilities. Contact your local government for information regarding the
collection systems available. If electrical appliances are disposed of in landfills
or dumps, hazardous substances can leak into the ground water, polluting the
food chain and damaging health and well-being.
14064_DHCER20FE Manual_V2.indd 9 7/12/17 4:25 PM

Phone: [phone]
Fax: [phone]
Email: [email protected]
Web: www.dimplex.co.nz
Glen Dimplex New Zealand Ltd
38 Harris Road, East Tamaki
Auckland, New Zealand
P.O. Box 58473, Botany
Manukau 2163, New Zealand
14064_DHCER20FE Manual_V2.indd 10 7/12/17 4:25 PM