Dimplex OCR15TIF User manual

For domestic household use only.
INSTRUCTION MANUAL
Oil Filled Column Heaters
Models: OCR15FA, OCR15TIF, OCR24FA &
OCR24TIF
08/54538/0 Issue 2

IMPORTANT
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND
RETAINED FOR FUTURE REFERENCE.
Note also the information presented on the appliance
CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/
OR DAMAGE AND MAY INVALIDATE YOUR WARRANTY
Please read the operating instructions carefully before using your product
for the first time and keep them in a safe place.
• When using electrical appliances, basic precautions should always be
followed to reduce the risk of fire, electrical shock and injury to persons,
including the following:
• If the appliance is damaged, check with the supplier before installation
and operation.
- Do not use outdoors.
- Do not use in the immediate surroundings of a bath, shower or
a swimming pool.
- Do not use this heater if it has been dropped.
- Do not use if there are visible signs of damage to the heater.
- Use this heater on a horizontal and stable surface, or fix it to
the wall, as applicable.
• Do not locate the appliance immediately below a fixed socket outlet or
connection box.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the
appliance.
• CAUTION: Some parts of this product can become very hot and cause
burns. Particular attention must be given where children and vulnerable
people are present.
• IMPORTANT: Only use this heater on a horizontal and stable surface
with the castors attached.
• WARNING: In order to avoid overheating, do not cover the heater.
• The Heater carries this warning symbol indicating that it must
not be covered.
• Do not use this appliance in series with a thermal control, a program
controller, a timer or any other device that switches on the heat
automatically, since a fire risk exists when the appliance is accidentally
covered or displaced.
2

• In the event of a fault, unplug the appliance.
• Unplug the appliance when not required for long periods.
• This product is intended for INDOOR RESIDENTIAL applications only.
• DO NOT cover cord with carpeting, throw rugs, runners, or similar
coverings.
• DO NOT route cord under furniture or appliances. Take care to position
the cord away from traffic areas and where it will not be a tripping
hazard.
• This appliance must not be used in a bathroom.
• Although this appliance complies with safety standards, we do not
recommend its use on deep pile carpets or on long hair type of rugs
• The appliance must be positioned so that the plug is accessible.
• If the supply cord is damaged it must be replaced by the manufacturer
or service agent or a similarly qualified person in order to avoid a hazard.
• Keep the supply cord away from the front of the appliance.
• Do not use this heater in small rooms when they are occupied by
persons not capable of leaving the room on their own, unless constant
supervision is provided.
• To reduce the risk of fire, keep textiles, curtains and or flammable material
a minimum distance of 1m from the air outlet.
• DO NOT place material or garments on the appliance, or obstruct the
air circulation around the appliance, for instance by curtains or furniture,
as this could cause overheating and a fire risk.
• In order to avoid a hazard due to inadvertent resetting of the thermal cut-
out, this appliance must not be supplied through an external switching
device, such as a timer, or connected to a circuit that is regularly switched
on and off by the utility.
IMPORTANT
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND
RETAINED FOR FUTURE REFERENCE.
Note also the information presented on the appliance
3

Exposed to the
weather outdoors
Near water If the power cable
wires are frayed or cut
Where small children
may be left unattended
No extension leads or
power boards
Where there is risk
of fire or close to
a naked flame
Where the power
cable may be
damaged
On a slope or
uneven surface
Where it may be
damaged by
chemicals
If there is a risk
of water falling on
the unit
Where there is a risk
of interference by
foreign objects
This product is not
made for DIY repair
4

Model no. OCR15FA OCR15TIF OCR24FA OCR24TIF
Power supply 230-240V~, 50Hz
Rated power 1500W 2400W
Heat settings
3
Thermostat Y
Timer N Y N Y
Turbo Fan Y Y Y Y
Weight (net) 8.2kg 8.46kg 12.6kg 12.33kg
Dimensions (w x d x h)
310 x 280 x
635mm
310 x 280 x
635mm
470 x 280 x
635mm
470 x 280 x
635mm
Specifications
For greater precision, please always refer to the rating label placed on the product.
WARNING THIS APPLIANCE MUST BE EARTHED
5

Fitting The Castors
B
A
C
D
WARNING The radiator must only be operated with the wheels and castors fitted and
in an upright position. The castors must be fitted to the control panel and between the
last and second last fin on the opposite end, as shown in Fig.1.
1. To fit the castors, turn the radiator upside down on a carpet or other soft surface
to avoid damage. Warning: The radiator is heavy – ensure that it is supported to
prevent it from toppling. Ask a second person to help with this if necessary.
2. Locate the wire clamp (A) and remove the winged nut (C). Insert the non threaded
end of the wire clamp into one of the holes in the castor plate (B) as shown. Feed
the threaded end of the wire clamp between the last and second last column fins
ensuring the wire clamp wraps around the column body (sump). Some manipulation
of the plate and clamp will be required. The threaded end should then be passed
through the castor plate and secured using the wing nut.
3. To fit the castor to the control end, position the castor plate in position and secure
using the wing bolts (D). There are guides to ensure the correct positioning and
orientation of the caster plate.
4. Return the radiator to the correct orientation so it rests on the castors. The product
is now ready for use.
Fig. 1
6

Positioning
Select the position for the heater ensuring there is clearance from any furniture and
fittings of at least 300mm above the heater and 150mm each side and 300mm from
the control and end panel. We recommend maximising the clearance where possible.
NOTE: The radiator is designed for operation on an AC electricity supply, and is only
suitable for domestic use and similar indoor locations.
Tips
• The radiator is fitted with castors and a handle for ease of movement.
• A rotary selector switch provides the ability to choose an available heat output
and an adjustable thermostat enables the room temperature to be controlled
accordingly.
• Once the castors have been correctly fitted, no other assembly is required, just
plug and play!
Safety Features
This appliance incorporates a number of safety devices. In addition to the ‘Important
Safety Advice’ section your attention is drawn to the following;
Tilt Switch
The tilt switch will prevent the heater from working if it is accidentally tipped over on
its side.
If the radiator is tipped over while it is hot, disconnect the power and allow it to cool,
then stand the radiator back upright. Reconnect the power - normal operation should
be resumed.
Overheat Protection
The heater is fitted with a temperature limiter which will reduce the output of the heater
should it overheat for any reason. The product will return to normal operation after the
cause of the over heating has been rectified.
7

Thermostat
Off/Heat selection
switch
Neon Indicator
Turbo
Cable Wrap
Timer
Turbo
Switch
Operation
IMPORTANT - OBJECTS OR CLOTHING MUST NOT BE PLACED ON THIS HEATER.
Before using the heater ensure that all warnings and instructions have been read
carefully. To activate the heater simply plug it in. Neon indicator lights located at
the control area will illuminate when the appliance is plugged into the mains. This
indicates the appliance is energised and ready to use.
Please note – The element has been coated with a protective film which will burn off
during the first few minutes of use, this may cause a small amount of fuming. This is
quite normal – the fumes are non-toxic and will quickly disappear.
We recommend that you open a window to ventilate the room when using the heater
for the first time.
CONTROLS
Fig. 2
Fig. 3
8

Operation
Thermostat
The Thermostat, see Fig.2 controls the heat output according to the room temperature.
This ensures that the heater will not produce heat unnecessarily when the room is
warm.
1. To set the temperature you require, turn the thermostat knob clockwise until the
required setting is reached. Alternatively to heat a cold room quickly, turn the
thermostat knob up fully.
2. When the room has reached the desired temperature, turn the thermostat knob
anti-clockwise until the thermostat just clicks off. The heater will now automatically
operate at this temperature.
3. The thermostat also has a frost protection setting marked '*' This setting is useful
in areas such as garages, to prevent frost damage. If the thermostat is set to its
minimum setting '*' the heater will cycle on and off to maintain a temperature of
approximately 5° to help protect against frost.
Note – Should the heater fail to come on when the thermostat is at a low setting, this
may be due to the room temperature being higher than the thermostat setting.
Heat Selector Switches (see Fig.3)
Heat selection is provided via a rotary switch offering four settings. The heat output
can be altered to suit the application, conditions and for improve the economy of
operation.
Available output options are as follows:
Switch setting With
Turbo
ON
Only
Turbo
ON
Model O I II III
0CR15FA
Off 500W 700W 1200W 1500W 300W
OCF15TIF Off 500W 700W 1200W 1500W 300W
OCR24FA Off 900W 1200W 2100W 2400W 300W
OCR24TIF Off 900W 1200W 2100W 2400W 300W
9

Timer Model
ELECTROMECHANICAL TIMER (TIF models)
Setting the time of day
To set the time of day, rotate the timer dial clockwise (indicated by the arrow) until the
correct time of day is opposite the reference mark
- see Fig.4. The 24-hour clock is
used; e.g. time shown for 4pm is '16' (16:00hrs).
Operation Modes
Set the operation mode using the slide switch on the timer - see Fig.5:
Position I - Manual operation
This setting allows power to the heater uninterrupted by the timer settings. The
heat selector switch and thermostat will control the output (see 'Controls').
Position - 'Auto' operation
This setting allows the heater to be switched ON and OFF according to a set 24
hour program period.
DO NOT disconnect this heater from the mains supply unless it is being taken out of
use (e.g. in summer or for storage), otherwise the timer clock will stop.
Fig. 4
Fig. 5
10