Dimplex LIBERTY SUITE LBY15-AU User manual

LIBERTY SUITE
LBY15-AU
8/54968/0 Issue 3
OCN 11816
Item No: 114630
The product complies with the Australian Safety Standards and the Standard
Electromagnetic Compatibility.

1
2
3
A
B
C
F
D
G
E
H
4

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Electrical Connection
WARNING: THIS APPLIANCE MUST BE
EARTHED
This heater must be used on an AC ~ supply
only and the voltage marked on the heater
must correspond to the supply voltage.
Before switching on, please read the safety
warnings and operating instructions.
WARNING: The heater must not be used if
the glass panels are damaged.
Do not use this heater with a programmer,
timer, separate remote-control system or
any other device that switches the heater
on automatically, since a re risk exists
if the heater is covered or positioned
incorrectly.
General
Unpack the heater carefully and retain
the packaging for possible future use, in
the event of moving or returning the re
to your supplier.
The re incorporates a ame effect, which
can be used with or without heating, so that
the comforting effect may be enjoyed at
any time of the year. Using the ame effect
on its own only requires little electricity.
Before connecting the heater check that
the supply voltage is the same as that
stated on the heater.
Please note: Used in an environment where
background noise is very low, it may be
possible to hear a sound which is related
to the operation of the ame effect. This
is normal and should not be a cause for
concern.
Important Safety Advice
When using electrical appliances, basic
precautions should be followed to
reduce the risk of re, electric shock, and
injury to persons, including the following:
If the appliance is damaged, check
immediately with the supplier before
installation and operation.
Do not use this appliance in the
immediate surroundings of a bath,
shower or swimming pool.
Do not use outdoors.
This appliance must not be located
immediately above or below a fixed
socket outlet or connection box.
WARNING: The appliance carries
the Warning Symbol indicating that
it must not be covered or has a Do
not cover label. Do not cover or
obstruct in any way the heat outlet grille
located above the ame window on the
appliance Overheating will result if the
appliance is accidentally covered. Do
not place material or garments on the
appliance, or obstruct the air circulation
around the appliance, for instance by
curtains or furniture, as this could cause
overheating and a re risk.
In the event of a fault unplug the heater.
Unplug the appliance when not required
for long periods.The supply cord must
be placed on the right hand side of
the heater away from the heat outlet
underneath the appliance.
This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible
for their safety.
Children should be supervised to ensure
they do not play with the appliance.
Prior to cleaning or other maintenance,
the appliance must be disconnected
from the supply mains.
The appliance must be positioned so that
the plug is accessible.
If the supply cord is damaged it must be
replaced by the manufacturer or service
agent or similarly qualified person in
order to avoid a hazard.
CAUTION: In order to avoid a hazard due
to inadvertent resetting of the thermal
cut-out, this appliance must not be
supplied through an external switching
device, such as a timer, or connected
to a circuit that is regularly switched on
and off by the utility.
CAUTION - Some parts of this product
can become very hot and cause burns.
Particular attention has to be given
where children and vulnerable people
are present.

Icon Function Description
APower Press to turn unit Off or On.
• Unit Off
Press to turn everything Off. Press again to turn unit On with previous settings.
• Unit On
Press to turn unit On with previous settings.
- If the flame effect was On, the flame will turn on and the previous heat setting will
be activated (On or Off). Display will show current heater temperature setting and
after 2 sec displays the room temperature.
- [remote only] If the flame effect was Off, the previous heat setting will be
activated (On or Off).
- [panel only] If the flame effect was Off, the flame will turn on and the previous
heat setting will be activated (On or Off)
BHeat • Heat On
Press to turn heat On (indicated by 1 short beep). Display will show current heater
temperature setting and after 2 sec displays room temperature. Use the Temp icon
to change the heater temperature setting.
• Heat Off
Press to turn heat Off (indicated by 1 short beep).
NOTE: After the heater is switched o󰀨, the fan will continue on for 60 seconds before turning
o󰀨.
CTemp Press multiple times to raise the heater temperature in 1oF (1oC) increments. Display
will show current temperature. Temperature range is 62o-78oF (17o-26oC).
This feature is active whenever the heat is enabled.
DFlame Speed Press multiple times to toggle through flame speeds (minimum, medium, maximum).
Display will show current speed number (F1, F2, F3 respectively).
EColor Themes Press multiple times to change the media and flame base colors. This feature is
active only when the flame effect is On. Display will show theme (t0, t1, t2, etc.)
XHD28L, XHD26L or XHD23L (Log Unit) themes:
• Theme t0 - no flame
• Theme t1 - Natural (flame base off)
• Theme t2 - Red Highlights (flame base red/orange)
• Theme t3 - Blue Highlights (flame base blue)
FBrightness Press to change the flame and logs brightness. Display will show b3, b1, b2
respectively.
• High
• Low
• Medium
GFlame Press to turn the flame effect On. Press again to turn the flame effect Off.
HTimer Press multiple times to change the sleep timer by 0.5 hr from 0.5 hr to 8 hr before
turning off. Press again, the remaining time on the timer displays.
User Modes:
Mode Name /Discription Action (Actions cannot be input by remote control)
Change Celsius (0C) to
Fahrenheit (0F)
Press both Temp Button ( ) and flame speed( ) on the unit and hold until beep is
heard and display flashes. (To revert back to Celsius repeat this action)
Disable / Enable Heat
Options
Hold both Heat Button ( ) and Temp Button ( ), on the unit, for 2 seconds, when the
heater has been disabled the display will read “--” and beep. To enable heat repeat this
action.
Controls: See Fig. 2

Resetting the Temperature Cutout Switch
Should the heater overheat, an automatic cutout will turn the heater off. It will not come back on without being reset.
To reset the cutout switch, unplug the unit and wait 5 minutes before plugging it back in.
Remote Control- See Fig. 2
The maximum range of use is ~ 9 metres.
NOTE: It takes time for the receiver to respond to the transmitter.
NOTE: The reciever for the remote control is located in the display, aim the remote control in this direction when inputting
commands.
Do not press the buttons more than once within two seconds for correct operation.
Battery Information
1. To activate the remote control remove the clear battery isolation strip at the base of the remote control, which is used
to ensure your remote control reaches you fully charged.
2. To replace the remote control battery, turn over the remote control, and follow the diagram embossed on the remote
control
3. This remote requires 1 x 3V CR2025 button battery.
WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN
1. Swallowing may lead to serious injury in as little as 2 hours or death, due to the chemical burns and potential perforation
of the oesophagus.
2. If you suspect your child has swallowed or inserted a button battery immediately call the 24-hour Poisons Inforation Centre
on 13 11 26 (in Australia) or 0800 764 766 (in New Zealand) for fast, expert advice.
3. Examine devices and make sure the battery compartment is correctly secured, e.g. that the screw or other mechanical
fastener is tightened. Do not use if the compartment is not secure.
4. Dispose of used button batteries immediately and safely. at batteries can still be dangerous.
Tipping Restraint- See Fig. 3
WARNING: FALLING OR TIPPING APPLIANCES CAN CAUSE INJURY OR DEATH OF YOUNG CHILDREN, PLEASE ENSURE CHILDREN
DO NOT CLIMB, HANG OR STAND ON THIS PRODUCT.
WARNING: THE APPLIANCE IS PROVIDED WITH A TIPPING RESTRAINT, THIS RESTRAINT IS NOT A SUBSTITUTE FOR PROPER ADULT
SUPERVISION. THIS RESTRAINT MAY PROVIDE PROTECTION AGAINST TIPPING FURNITURE. DO NOT ALLOW CHILDREN TO CLIMB
ON FURNITURE. FAILURE TO DETACH THIS RESTRAINT BEFORE MOVING FURNITURE MAY RESULT IN INJURY AND DAMAGE.
This product is provided with a ‘Tipping Restraint Kit’ as shown in Fig 3, to prevent the product accidentally tipping. Instructions
are supplied with this kit please follow these instructions carefully. This accessory is intended to improve the safety of the
the product.
Thermal Safety Cut-out
The built-in overheat cut-out, switches off the appliance automatically in the event of a fault! Should this occur switch off
the appliance or disconnect the mains plug from the socket.
Remove any obstructions which may have caused the overheating. After a short cooling down phase, the appliance is
ready for use again! If the fault should occur again, contact your local dealer!
WARNING: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be
supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and
off by the utility.
Mounting Glass frame- See Fig. 4
Product comes with glass frame not xed to re, but packed separately to the re in its own packing.
To x frame the hooks on both side at the top need to be aligned up with corresponding slots on both sides of the re.
When hooked in place the frame hangs vertical covering the re.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.
Light Emitting Diode
This re is tted with LED (Light Emitting Diode) lamps. These LED lamps are maintenance-free and should not require replacing
during the life of the product.

Glen Dimplex Australia
8 Lakeview Drive,
Scoresby,
VIC 3179,
Australia
www.dimplex.com.au
[email protected]
Ph: 1300 556 816
Glen Dimplex Australasia Ltd.
35 Harris Road,
East Tamaki,
Auckland
New Zealand
www.dimplex.co.nz
[email protected]
Ph: 0800 666 2824
© Glen Dimplex Heating & Ventilation.
All rights reserved. Material contained in this publication may not be reproduced in whole or part, without
prior permission in writing of Glen Dimplex Heating & Ventilation.
Cleaning
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive cleaners. The glass viewing screen should be cleaned
carefully with a soft cloth.
DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or uff the soft brush attachment of a vacuum cleaner should occasionally be used
to clean the outlet grille of the fan heater.
WARNING: do not operate the product without the grille and outer glass in position as this may effect the operation of the
heater.
Recycling
At the end of the electrical products useful life it should not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or retailer for recycling advice in your country.
After Sales Service
Should you require after sales service or should you need to purchase any spares, please contact the retailer from whom
the appliance was purchased or contact the service number relevant to your country on the warranty card.
Please do not return a faulty product to us in the rst instance as this may result in loss or damage and delay in providing
you with a satisfactory service. Please retain your receipt as proof of purchase.
Specication
Volts: 230-240V ~50Hz
Watts: 1400-1500W
Effect: 7W
Country of Origin: China