Dino lift DINO 135T User manual

OPERATING
INSTRUCTIONS
DINO 135T •150T •180T
Dealer:Manufacturer:
Dinolift Oy
Raikkolantie 145
FI-32210 LOIMAA
Tel. [phone]
[email protected]
www.dinolift.com

3
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
Valid from serial number
135T 13630 -->
150T 2124 -->
180T 5047 -->

4
Operating instructions•DINO 135T •150T •180T
CONTENTS
1. TO THE OPERATOR ................................................................................................... 7
1.1. OVERVIEW OF THE UNIT.................................................................................. 8
1.2. INTENDED USE OF THE WORK PLATFORM ................................................... 8
2. TECHNICAL SPECIFICATIONS ................................................................................. 9
2.1. DIMENSION DRAWINGS ................................................................................. 10
2.1.1. 135T............................................................................................................................. 10
2.1.2. 150T............................................................................................................................. 11
2.1.3. 180T............................................................................................................................. 12
2.2. REACH DIAGRAM ............................................................................................ 13
2.2.1. 135T............................................................................................................................. 13
2.2.2. 150T............................................................................................................................. 14
2.2.3. 180T............................................................................................................................. 15
2.3. EXAMPLE OF THE MACHINE’S NAMEPLATE ................................................ 16
2.4. EXAMPLE OF EU DECLARATION OF CONFORMITY .................................... 17
2.5. SAMPLE OF INSPECTION PROTOCOL FOR THE ACCESS PLATFORM ..... 18
3. SAFETY..................................................................................................................... 20
3.1. SAFETY INSTRUCTIONS................................................................................. 20
3.2. SAFETY-RELATED NOTIFICATIONS............................................................... 24
3.3. SAFETY LABELS ............................................................................................. 26
3.4. SAFETY DEVICES............................................................................................ 29
4. STRUCTURE AND FUNCTIONS OF THE WORK PLATFORM ............................... 33
4.1. STRUCTURE OF THE WORK PLATFORM...................................................... 33
4.2. FUNCTIONS OF THE WORK PLATFORM....................................................... 34
4.3. OPERATING CONTROLS FOR THE FUNCTIONS.......................................... 35
4.3.1. Operating controls in the chassis control centre.......................................................... 35
4.3.2. Operating controls for the driving device .....................................................................36
4.3.3. Operating controls for the outriggers ...........................................................................36
4.3.4. Operating controls in platform control centre UCB ...................................................... 37
4.3.5. Setup with two control levers (option).......................................................................... 39
5. OPERATING INSTRUCTIONS .................................................................................. 40
5.1. START-UP ......................................................................................................... 40
5.1.1. Worksite inspection...................................................................................................... 40
5.1.2. Positioning the lift......................................................................................................... 41
5.1.3. Connecting the power supply to the lift........................................................................ 42
5.1.4. Starting up ................................................................................................................... 43
5.1.5. Supporting the lift......................................................................................................... 43
5.2. OPERATION...................................................................................................... 44
5.2.1. Operating the lift from the chassis control centre ........................................................ 44
5.2.2. Operating the lift from the platform control centre ....................................................... 44
5.2.3. Special instructions for winter use ...............................................................................47
5.2.4. Ending the work ........................................................................................................... 47

5
5.3. TRANSFERRING THE LIFT.............................................................................. 48
5.3.1. Preparing the lift for transport ......................................................................................48
5.3.2. Using the driving device............................................................................................... 49
5.3.3. Towing the lift............................................................................................................... 51
5.3.4. Lifting the device.......................................................................................................... 52
5.4. LONG-TERM STORAGE .................................................................................. 53
5.5. IN CASE OF EMERGENCY.............................................................................. 54
5.5.1. When at risk of losing the stability ............................................................................... 54
5.5.2. In case of overloading.................................................................................................. 54
5.5.3. In case of power failure................................................................................................ 54
5.5.4. In case of malfunction, when even the emergency descent system is not operational55
6. INSTRUCTIONS FOR FAULT-FINDING ................................................................... 56
7. MAINTENANCE SCHEDULE.................................................................................... 60
7.1. SCHEDULE FOR INSPECTIONS REQUIRED BY THE AUTHORITIES .......... 62
7.2. LUBRICATION PLAN ........................................................................................ 63
8. ROUTINE MAINTENANCE DURING OPERATION .................................................. 64
8.1. INSTRUCTIONS FOR DAILY MAINTENANCE AND INSPECTIONS .............. 65
8.1.1. Check the condition of chassis, the boom and the work platform................................ 65
8.1.2. Check the tyres and tyre pressure............................................................................... 65
8.1.3. Check the lights ........................................................................................................... 65
8.1.4. Check the hydraulic oil level ........................................................................................65
8.1.5. Check the hydraulic hoses, pipes and connectors ...................................................... 65
8.1.6. Check the operation of the safety limit switches.......................................................... 66
8.1.7. Check the operation of the emergency descent, the emergency stop and the
sound signal................................................................................................................. 66
8.1.8. Decals, stickers and signs ...........................................................................................66
8.1.9. Instruction manuals...................................................................................................... 66
9. CHANGE OF OWNER............................................................................................... 69

6
Operating instructions•DINO 135T •150T •180T
BLANK

7
1. TO THE OPERATOR
Keep this manual on the work platform of the lift in the box reserved for it. If the instruction
manual gets lost, damaged, or for some other reason becomes unreadable, order a new
manual from the manufacturer.
This manual is intended to familiarise the user with the structure and functions of the work
platform, as well as with its appropriate use. The manual provides guidance on the service
measures that are the responsibility of the user of the work platform.
Other maintenance procedures on the work platform require special skills, special tools or
accurate knowledge about measurements or adjusted values. Guidance for these measures
is provided in a separate service manual. For situations that require service or repair
measures, contact the authorised service provider, importer or manufacturer.
DANGER
WARNING
CAUTION
NOTICE
Read all the instructions in this manual before using the aerial work platform. Make sure that
you have understood all the instructions. The instructions must absolutely be followed during
operation and maintenance of the aerial work platform.
When handling the unit, in addition to the instructions in this manual, the user must also
observe the local legislation, the guidelines stipulated by the employer, and regulations valid
at the work site.
Dinolift Oy is constantly developing its products. For this reason, the contents of this manual
might not always be in full compliance with the most recent version of the product. Dinolift Oy
reserves the right to modify the product without prior notice. Dinolift Oy assumes no liability
for any problems caused by changed or missing data or mistakes in this manual.
Please consult your dealer or the manufacturer for more information and detailed
instructions.

8
Operating instructions•DINO 135T •150T •180T
1.1. OVERVIEW OF THE UNIT
This unit is a trailer mounted, towable aerial work platform.
It is an aerial work platform, which complies with the EN280 type 1, where travelling is only
allowed with the platform in transport conguration.
For the operation the lift shall be supported by its hydraulic outriggers, extended so that the
wheels of the trailer lift off the ground.
1.2. INTENDED USE OF THE WORK PLATFORM
The aerial work platform is exclusively intended for transferring people and tools and acting
as a work platform within its permissible load-bearing capacity and reach (refer to the
“Technical Specications” table and the “Reach Diagram”).
The intended use also covers:
• Following all the instructions in the Operating Instructions
• Performance of the inspections and maintenance operations.
This aerial work platform is NOT insulated, and does not offer protection against contact with
electric current. The aerial work platform must not be used for work on electric systems.
Observe the safety instructions concerning the operating environment, and the restrictions
given in them,
DANGER
WARNING
CAUTION
NOTICE
The operator must receive instructions and consent from the manufacturer for all
such specic work methods or conditions that the manufacturer has not explicitly
dened in the unit's operation and maintenance instructions.
The primary power source of the lift is electric motor. The outriggers and the boom system
are hydraulically powered.
As an option, the lifts can be equipped with a driving device that can be controlled from the
ground.
Consult the chapters “Technical data" and “Structure and functions of the work platform" in
this manual for more detailed information about the lift.

9
2. TECHNICAL SPECIFICATIONS
135T 150T 180T
Max. working height 13,5 m 15,0 m 18,0 m
Max. platform height 11,5 m 13,0 m 16,0 m
Max. outreach 9,1 m 10,0 m 10,7 m
Boom rotation continuous
Platform rotation 90°
Turn area refer to the reach diagram
Support width 3,8 / 4,2 m 3,8 / 4,2 m 3,8 / 4,2 m
Transport width 1,78 m 1,78 m 1,78 m
Transport length 5,96 m 6,53 m 7,46 m
Transport height 2,16 m 2,24 m 2,19 m
Weight (incl. Honda power unit) 1635 kg 1675 kg 1840 kg
Max. allowed load on platform 215 kg
Max. number of persons + additional load 2 persons + 55 kg
Max. allowed sideways load (caused by persons) 400 N
Max. lateral inclination (chassis) ±0,3°
Max. allowed gradient of ground to the side 2,4° 2,4° 2,4°
Max. allowed gradient of ground lengthwise 4,0° 3,8° 3,8°
Max. wind speed during operation 12,5 m/s
Min. ambient temperature when working - 20 °C
Max. support force on the outriggers 11300 N 12800 N 16800 N
Platform size 0,7 x 1,3 m
Gradeability 25%
Socket outlets on the platform 2 x 230V/50Hz/16A
Power supply 0 0 0
- mains current 230V/50Hz/10A
Sound pressure level < 70 dB
Whole-body vibration Not detectable
Honda GX200SXE
Fuel Petrol
Net power 4.1 kW (5,5 hp)
Fuel tank volume 3,1 l
Oil volume 0,6 l
Fuel consumption 1,7 l/h
Sound pressure level 98 dB
Whole-body vibration < 0,5 m/s2
Optional engines

10
Operating instructions•DINO 135T •150T •180T
2.1. DIMENSION DRAWINGS
2.1.1. 135T

11
2.1.2. 150T

12
Operating instructions•DINO 135T •150T •180T
2.1.3. 180T

13
2.2. REACH DIAGRAM
2.2.1. 135T
215KG
475LB
120KG
265LB

14
Operating instructions•DINO 135T •150T •180T
215KG
475LB
120KG
265LB
80KG
175LB
2.2.2. 150T

15
2.2.3. 180T
215KG
475LB
120KG
265LB
80KG
175LB

16
Operating instructions•DINO 135T •150T •180T
2.3. EXAMPLE OF THE MACHINE’S NAMEPLATE
The name of the manufacturer, and the production number and serial number of the machine
have been marked on the nameplate as shown in the picture below.
Weight kg Max load
Max load of persons Additional load
Max side force Max inclination of chassis
Voltage Frequency
Min operating temp. Max wind force
Number of manufacture
Year of manufacture Address of manufacture
Raikkolantie 145
32210 Loimaa
FINLAND
400 N
230 V
-20 C
o
12,5 m/s
50 Hz
o
kg
kg
Type Manufacturer
DINO
2
215
55
0.3
54.516
The nameplate of the lift is located on the
right-hand side of the tow-bar, as shown in
the picture.
The serial number is also engraved in the
lift's chassis, on the upper surface of the
right-hand tow-bar.
The nameplate of the trailer is located on
the tow-bar, on the right-hand side of the
nameplate of the lift, as shown in the picture.
Following data is written on the plate:
EU Type Approval Number (if available)
Serial number
Total weight kg
0Maximum allowed weight on the towing
hitch kg
1 Maximum allowed axle weight kg
2 kg

17
2.4. EXAMPLE OF EU DECLARATION OF CONFORMITY
EU declaration of conformity for machine
Manufacturer
Dinolift Oy
Raikkolantie 145
FI-32210 Loimaa, FINLAND
declares that
DINO 135T Aerial Work Platform no YGC0D135TF0013562
conforms to the provisions of the Machine Directive 2006/42/EC
as well as the national decree (VNA 400/2008), through which they have been brought
into effect
The inspection in accordance with Annex IX to the directive 2006/42/EC has been
carried out by the notied body no. 0537,
VTT
P.O.Box 1300
FI-33101 Tampere, FINLAND
has granted the certicate no. VTT 174/524/14
In addition, the aerial work platform also complies with the provisions of the following
European Directives:
2006/95/EC, 2000/14/EC, 2004/108/EC
Measured sound power level Lwa ( 99 + 1,5 ) 100,5 dB
Guaranteed sound power level Lwa 100,5 + 0,5 dB
To the assessment procedure of conformity has been applied: 2000/14/EC, Annex V:
Internal control of production.
In designing the machine, the following harmonised standards have been applied:
SFS-EN 280:2013, SFS-EN 60204-1/A1, SFS-EN-ISO 12100
The person, who has compiled the technical construction le: Santtu Siivola
Chief Engineer
Dinolift Oy, Raikkolantie 145,
FI-32210 Loimaa, FINLAND
Loimaa 11.05.2015
-----------------------------------------
Tuomo Nykänen
Production director

18
Operating instructions•DINO 135T •150T •180T
2.5. SAMPLE OF INSPECTION PROTOCOL FOR THE ACCESS PLATFORM
TEST CERTIFICATE
DATE: 7.1.2015
START-UP TESTS:
Inspection place: Dinolift O
y
Inspector's signature: 1146
BASIC KNOWLEDG
E
Manufacturer: Dinolift O
y
Place of manufacture: Finland
Address: Raikkolantie 14
5
32210 LOIMA
A
Importer:
Type of lift:
Chassis:
Boom:
Outriggers:
TECHNICAL SPECIFICATION
Machine and type: DINO 135
T
Max. platform height 11,5m
Number of manufacture
Y
GC0D135TF001353
6
Max. outreach: depend on load: Depend on load
Year of manufacture 2015
Max. lifting capacity: 215 kg Boom rotation: Continuous
Max. person number: 2Support width: 3,8m
Max. additional load: 55kg Transport width: 1,78 m
Power supply: 230VA
C
Transport length: 5,94 m
Lowest temperature: -20 °C Transport height: 2,14 m
Weight: 1635 kg Basket size: 0,7x1,3 m
Inspection points: (Y = meet standards N = do not meet standards)
Y N
Y
N
A. STRENGTH 6. Plate for supports
1. Certificate of material 7. Safety colours
2. Certificate of strength
D. SAFETY REQUIREMENTS
B. STABILITY 1. Indicating device for horizontal
1. Certificate of stability test position
2. Working space diagram 2. Locking device and lockings
3. Stop device for lifting
C. GENERAL REQUIREMENTS 4. Stop for opening of support
1. User's manual 5. Safety distances
2. Place for safekeeping for user's manual 6. Position of working face
3. Machine plate - checking plate 7. Structure of working face
4. Load plate 8. Emergency descent system
5. Warning plate 9. Limit devices
www.dinolift.com
Boom platform Scissor platform Mast platform
Car Self propelled Trailer mounted
Articulated boom Telescope boom Articulated telescope boom
Scissor Fixed mast Telescope mast
Hydraulic turning Hydraulic pushing Mechanical

19
The initial inspection and test loading of the Dino aerial work platforms is performed by the
manufacturer. A protocol, drawn up during the inspection, will accompany the lift.
The protocols of the start-up and periodic inspections must be kept with the lift or its
immediate proximity for at least ve years.
ECIVEDYTEFAS.GSECNAILPPACIRTCELE.E
hctiwstimilytefaS.1secnailppacirtcelE.1
2. Sound signal
F. CONTROL DEVICES
TSETGNIDAOL.HsnoitcetorP.1
)%051(gk323=tsetdaolrevO.1snoitcerid/slobmyS.2
)%011(gk732=tsetlanoitknuF.2sgnicalP.3
4. Emergency stop
FAILINGS AND NOTES
:erutangiS:etaD.deriaperneebevahsgniliaF
Dinolift O
y
Raikkolantie 145
FIN-32210 LOIMAA, FINLAND
Tel. +358 - 20 - 1772 400, Fax +358 - 2 - 7627 160, e-mail: [email protected]
m

20
Operating instructions•DINO 135T •150T •180T
3. SAFETY
All the essential safety instructions and warnings, relevant to transport, use and maintenance
of the lift, are described in this chapter.
DANGER
WARNING
CAUTION
NOTICE
Failure to observe these instructions and safety regulations may cause a severe injury or
even death. Familiarise yourself with all the safety regulations, operating instructions and
signs afxed to the machine, and follow them.
Make sure that you understand all the safety instructions and regulations. Also make sure
that others operating the machine or working on the work platform are familiar with these
instructions.
3.1. SAFETY INSTRUCTIONS
Only specially trained personnel with authorisation in writing, who are well familiarised with
the device, and at least 18-years old, are allowed to operate the unit.
Keep the lift free of any dirt, which may impair safe operation, and impede the inspection of
the structures.
The device must be serviced and inspected regularly.
Only skilled persons, familiar with the service and repair instructions for the lift, are allowed
to carry out servicing and repair work.
It is strictly prohibited to use a lift which is out of order.
Never remove or disable any safety devices of the machine.
DANGER
WARNING
CAUTION
NOTICE
The device must neither be altered without the manufacturer’s consent nor be used under
conditions, which do not meet the manufacturer's requirements.
The operator must be given instructions and consent from the manufacturer for all such
specic work methods or conditions that the manufacturer has not explicitly dened.