Dinstar DAG2500-48S User manual

Quick Installation Guide
DAG2500-48S
DAG2500-72S
DAG2500-96S
Thanks for Choosing Dinstar’s VoIP Gateway!
Please read this guide carefully before installing the gateway. If you need any
technical support, .please contact us
Tel: [phone]
Email: [e-mail]
Website: www.dinstar.com

Please confirm your product model before installation and follow the installation guideline for the
model.
Product Model & Number of Ports
1
Description of Indicators
2
Indicator Definition Status Description
Power
Indicator
Running
Indicator
Telephone In-use
Indicator
On
On
On
Off
Off
Off
Off
The gateway is powered on
The gateway is powered off or there is
no power supply
Off
Slow Flashing
Green Flashing
Network Link
Indicator
Network Speed
Indicator
PWR
RUN
FXS
MGMT
The gateway is running properly
SIP account is registered successfully
The gateway is running improperly
FXS port is currently occupied by a call
FXS port is idle or faulty
The gateway is properly connected to network
The gateway is not connected to network or
network connection is improper way.
Work at 100Mbps
Work at 10Mbps
Fast Flashing
Model
Port Type
DAG2500-48S
Network Port RJ21
2 12
18
24
3
3
3
3
4
DAG2500-72S
DAG2500-96S
RJ45
For the DAG 2500 series product, FXS Ports support two types, RJ21 or RJ45. Please check
the table above for the number of ports on specific product models;
GE0/
GE1 On Work at 1000Mbps
Network Link
Indicator Off
The gateway is properly connected to network
The gateway is not connected to network
or network connection is improper way.
Network Speed
Indicator Off Work at 10Mbps
Green Flashing

Indicators & Interfaces
3
DAG2500-48/72/96S
Note: DAG2500-48/72/96S has a similar physical appearance except for the different number
of ports. And the AUX port on the front panel is a reserved interface.
04812 16 20 48 52 56 60 64 68 72 76 80 84 88 92
24 28 32 36 40 44
RUN
3711 15 19 23 51 55 59 63 67 71 75 79 83 87 91 95
27 31 35 39 43 47PWR
GE0
GE1
MGMT RST
AUX
CONSOLE
11-8
15-12
3-0
7-4
19-16
23-20
27-24
31-28
35-32
39-36
43-40
47-44
51-4859-56
63-60
91-88
95-92
83-80
87-84
75-72
79-76
67-64
71-68
POWER
71~48
95~72 47~24 23~0
DAG2500-96S
100-240VAC 50/60Hz
POWER
100-240VAC 50/60Hz
Power Indicator
Power Switch Power Jack
LAN Ports
Console Port
Grounding Lug
Running Indicator Telephone In-use Indicator
Reset Button
Management Port
FXS Ports(RJ21)
Power Switch Power Jack Grounding Lug FXS Ports(RJ45)
55-52

Installation Attentions
4
When installing the device, please confirm the type of telephone interface of the device: The
telephone interface type of the DAG2500-48S/72S/96S is RJ21 or RJ45;
* Please go to RJ45 & RJ21 Wire Sequence of this guideline to get more information about wire
Anti-jamming: to reduce the interference with telephone calls, it's highly recommended that
telephone lines connected to the gateway should be placed away from power cables.
Power supply: the power adapter of the gateway accepts 100-240V AC power supply. Please
ensure safe and stable power supply (The DAG2500-48/72/96S supports a dual 220v power
supply or dual 48v power supply).
Network bandwidth: please ensure there is enough network bandwidth so as to guarantee
stabilized running of the gateway.
Temperature and humidity: to avoid any accident that might cause malfunction, it's advised to
install the gateway in an equipment room where temperature and humidity are appropriate.
Ventilation：to avoid overheating, please do not pile up the gateway with other devices and make
sure the gateway has good ventilation around.
Mechanical load：please make sure the gateway is placed steadily to avoid damage. It's highly
advised to horizontally place the gateway on a flat surface or a cabinet.
sequence.
Installation Instructions
5
Connection Diagram for DAG2500-48S/72S/96S
Connect gateway with network via a switch
Network Cable
Switch
PC
Connect FXS ports with analog phones, connect gateway with power input and
grounding lug
100-240V AC
Grounding
Cable
Grounding
Lug
Network Cable
04812 16 20 48 52 56 60 64 68 72 76 80 84 88 92
24 28 32 36 40 44
RUN
3711 1 5 19 2 3 51 55 5 9 63 6 7 71 75 79 83 87 91 95
27 3 1 35 3 9 43 4 7PW R
GE 0
GE1
MG MT RS T
AUX
CO NSO LE
DAG2500-96S
POWER
71~48
95~72 47~24 23~0
100-240VAC 50/60Hz
Telephone
RJ21 Cable

RJ45 & RJ21 Wire Sequence
6
·RJ45 Wire Sequence
DAG2500-48S/72S/96S support RJ21 Interfaces for FXS connections. One RJ21 cable
has 25 pairs of wires, but the 25 pair of wires never used. It means that RJ21 interface
only support 24 pairs of RJ11 interfaces.
DAG2500-48S/72S/96S support RJ45 Interfaces for FXS connections. One RJ45 cable
can be split into four pairs of RJ11 interfaces. The outlook wire sequence of RJ45 cable
is shown as follows:
·RJ21 Wire Sequence
Pair 1
Pair 2
Pair 3
Pair 4
Orange & White
Orange
Green & White
Green
Blue& White
Blue
Brown & White
Brown
1
2
3
4
5
6
7
8
Call No.
Colour
PIN No.
White
P1
0
Blue
P26
1 2 34
White Orange White Green White Brown White Slate
P2
P27 P3 P28 P4 P29 P5 P30
Call No.
Colour
PIN No.
Red
P6
5
Blue
P31
68 9
Orange Green Brown Slate
P7 P32 P8
P33 P9 P34
P10
P35
7
Red Red Red Red
Call No.
Colour
PIN No.
Black
P11
10
Blue
P36
11 12 13 14
Orange Green Brown Slate
P12 P37 P13 P38 P14
P39
P15
P40
Black Black Black Black
Call No.
Colour
PIN No.
Yellow
P16
15
Blue
P41
16 17 18 19
Orange Green Brown Slate
P17
P42
P18
P43 P19 P44 P20 P45
Yellow Yellow Yellow Yellow
Call No.
20
21 22
23 24
Colour Violet Blue Orange Green Brown Slate
Violet Violet Violet Violet
PIN No.
P21
P46
P22
P47 P23 P48 P24 P49 P25
P50

Modify PC’s IP Address
7
Log in Web Management System
8
To log in the Web Management System of the gateway, firstly, you need to modify the IP
address of PC which is used to access the gateway and to make it at the same network
segment with the gateway.
On the PC, click ‘Network (or Ethernet) → Properties’.
Double-click ‘Internet Protocol Version 4 (TCP/IPv4)’.
Select ‘Use the following IP address’, and then enter an available IP address
‘192.168.11.XXX’ which is at the same network segment with ‘192.168.11.1’.
1
2
3
Enter the gateway's IP address in the browser (The default IP is 192.168.11.1).
Enter the administrator’s username and password to access the Web GUI. (By default
the admin password is admin)

Modify Gateway’s IP Address
9
Configure Gateway
10
Click Save and then restart the gateway for the new configurations to take effect.
(1) Configure SIP Server
(2) Configure SIP Account Information
If you want to modify the IP address of the gateway, please click ‘Network → Local
Network’ in the navigation tree on the left of the Web Management System, and then
input new IP address and DNS server address on the displayed interface.
Log in the Web Management System of the gateway, and then click SIP Server in the
navigation tree and then enter the address of the SIP server which is to be registered.
Click Save in the last.
Click Port in the navigation tree on the left, and then click Add. Input the SIP account
and authentication password assigned by the SIP server.

Basic Operations
11
More Details
12
IP Communication Solutions
Shenzhen Dinstar Co., Ltd.
Website: http://www.dinstar.com
This document only provides instructions for quick installation and basic configuration,
For detailed configuration and parameter explanation, please refer to user manual or
ask for online technical support.
Dial *158# to query the IP address of LAN port of the gateway;
Dial *159# to query the IP address of WAN port of the gateway;
Dial *114# to query the telephone number of a FXS port;
Dial *165*000000# to restore default IP address, username and password;
Restore factory default settings:
(1) dial *166*000000#;
(2) press the RST button for 7 seconds;then restart by manual;
(3) Log in the gateway and then click ‘Tools → Factory Reset’ , then click Apply
and restart the gateway.
Restart the gateway:
(1) Dial *111# to restart the gateway.
(2) Log in Web Management System, click ‘Tools → Restart’ in the navigation
tree on the left, and then click Restart on the displayed interface.