Dinstar UC350 User manual

Quick Installation Guide
UC350
Thanks for Choosing Dinstar’s VoIP Gateway!
Please read this guide carefully before installing the gateway. If you need any
technical support, .please contact us
Tel: [phone]
Email: [e-mail]
Website: www.dinstar.com

Model and Interfaces
1
Description of Indicators
2
Indicators Definition Status Description
Power Indicator
Running Indicator
Line status
Indicator
ON
ON
ON
OFF
OFF
OFF
OFF
The device is switched on
The power is switched off or there
is no power supply
ON/OFF
Blinking slowly
Blinking fastly
Network
Link Indicator
Network Speed
Indicator
PWR
RUN
FXS/FXO
GE
The device is running properly
The device is initializing
The device goes wrong
FXS/FXO Port busy
FXS/FXO port idle
The gateway is properly connected
to network
The gateway is not connected to network
or network connection is improper
Work at 1000Mbps
Network speed lower than 1000Mbps
Blinking fastly
Model
Interface
UC350
MCU Board User board slots
(optional）
RST
2*100/1000M, Base-T, RJ45
1* USB 2.0
1* Console port
FXS Board:
2* RJ45 with 8 FXS
FXO Board:
2* RJ45 with 8 FXO
E1/T1 Board:
4* E1/T1 Ports
The button is used to restart device
Note: The above table does not contain all the indicator information. For more
information, please refer to the user manual or contact technical support.
//

Indicators and Ports
3
UC350
M
C
U
M
C
U
Main Control Board
USB LAN Ports
Power Indicator
Running Indicator
F
X
S
F
X
S
F
X
O
F
X
O
F
X
O
F
X
O
M
C
U
M
C
U
M
C
U
M
C
U
MCU 0
MCU 1
SLOT0
SLOT2
SLOT1
SLOT3
D
T
U
D
T
U
PORT 0 PORT 1 PORT 2 PORT 3
Console Ports
Reset Ports
User Board Slot
Expandable E1 / FXS / FXO ports
/ /
OK
Welcome!
Ground Point Power Switch Power Jack Power Switch Power Jack Display Screen
Next
OK
Previous
Attentions before Installing
4
To guarantee device works normally and to lengthen the service life of the
device, the humidity of the equipment room where device is installed in
temperature should be 0 ℃~ 45 ℃;
Power supply of device should be 100 ~ 240V AC, and its socket is a three-
pin socket which should be grounded well;
To reduce the interference with telephone calls, it's highly recommended
that telephone lines connected to the gateway should be placed away from
power cables;

Installation Instruction
5
Network connection
Connect gateway with network via a switch
Router/Switch
192.168.12.1
Network Cable
192.168.11.1
Network Cable
F
X
S
F
X
S
F
X
O
F
X
O
F
X
O
F
X
O
M
C
U
M
C
U
M
C
U
M
C
U
MCU 0
MCU 1
SLOT0
SLOT2
SLOT1
SLOT3
D
T
U
D
T
U
PORT 0 PORT 1 PORT 2 PORT 3
PC
192.168.11.XXX
IP Network
Switch
/ /
OK
Welcome!
Ground Point
Grounding Cable
100-240V AC
Connect the power cord to power jack
Connect gateway with power input and ground point

Login Web GUI
6
The username is admin and password is admin@123#.
Check Network Status
7
Check GE0 and GE1 network status on the "Status → Overview" page.
Open the GUI in browser through IP HTTPS: XX.XX.XX.XX .The GE0 default is
192.168.12.1 and GE1 default is 192.168.11.1.

Modify Network Configuration
8
Log into the device and click "Network → Settings" at the top menu bar to configure
IP addresses of GE0 and GE1 ports.
Click “Save” and "reset" to make the settings take effect.

Create SIP Extensions
9
Click "Extension→ SIP" to create the SIP extension: add/delete/disable/enable, etc.
UC350 supports batch add or import account files.
Note: when add the extension, the profile should choose the corresponding one.
After setting, you need to click "apply" to make the settings take effect.
The registration status of SIP extension and SIP trunk can be checked on the
"Status → SIP" page.
If the status of the SIP account is "unregistered", it means that the device rejects
to register the extension.
If the status of a newly added SIP account is "registered", it means that the device
accepts the registration of the extension.

Add Trunk
10
SIP trunk
SIP trunks are used to connect other SIP terminals or service providers. When add
a SIP trunk, you should choose corresponding SIP profile based on your current
network. The SIP trunk supports UDP/TCP/TLS.
Also, SIP trunk status can be checked under Status → SIP page.

You can also create Trunk/FXO. It is an alternative to support calls through or from
PSTN.
FXO

E1/T1
You can set up ISDN PRI/SS7/R2 connections via digital E1/T1 ports. Please be
sure the E1/T1 physical connection is well connected, and PRI status is up and
active before configuring the call routing.

On the "Call Control → Route" interface, you can configure routes for incoming calls
and outgoing calls.
Configure Outbound / Inbound Rule
11
Basic Operation
12
Dial *158# to query the IP address of GE0 port of the device;
Dial *114# to query the telephone number of a FXS port;
Dial *111# to restart the device;
Click "system->Reboot" menu to perform reboot.
Note: Dialing *158# to query the IP address of GE0 port of the device is only
available for FXO/FXS user boards.If your user board is E1/T1 boards, it has to
query the IP address from CONSOLE.
The UC350 supports max 300 routes, the rule with a lower index has a higher
priority.
The key configuration of route is at “condition” part. Here, you can configure the
route based on the Caller/Called Number prefix and time.

More Details
13
IP Communication Solutions
Shenzhen Dinstar Co., Ltd.
Website: http://www.dinstar.com
Email:[e-mail]
Frequently Asked Questions
14
UC350 can support GE0/GE1 interconnection services at the same time, which
can make GE0 calls out of GE1. But the corresponding network port needs to be
selected in the extension or trunk. If the network port is selected incorrectly, it
will cause connection problems.
Does UC350 support dual network ports to access different networks for
interconnection and intercommunication to achieve business?
⑴
Yes , it supports video call (not conference call) such as VP2, H263, H264,
H261, and also supports fax (T.30 or T.38).
Does UC350 support video call and fax?
⑵
The storage method can support USB flash disk or SD card.
What method does the device support to store data?
⑶
If more additional FXS, FXO, and E1 ports are needed, you can connect to other
external VoIP gateways through SIP trunks.
How to expand the port when the port capacity is not sufficient?
⑷
The default FXO interface cable only supports the RJ45 interface, and the RJ11
port needs to be separated by a splitter. Refer to the user manual for specific
wiring methods.
Which wiring method is used for the equipment port?
⑸
You can factory reset the device via Web GUI.
How to factory reset the device?
⑹
This document only provides instructions for quick installation and basic
configuration.
For detailed configuration and Parameter explanation, Please refer to User
Manual or ask for technical support.