Dinstar DAG2000-16S User manual

Quick Installation Guide
DAG2000-16S
DAG2000-24S/32S
DAG2500-48S/64S/72S
DAG3000-112S
Thanks for Choosing Dinstar’s VoIP Gateway!
Please read this guide carefully before installing the gateway. If you need any technical
support, .please contact us
Tel: [phone]
Email: [e-mail]
Website: www.dinstar.com

Please check the model of your gateway before installation,and then refer to corresponding
installation instructions.
Product Model & Number of Ports
1
Description of Indicators
2
Indicator Definition Status Description
Power Indicator
Running Indicator
Telephone In-use
Indicator
On
On
On
Off
Off
Off
Off
The gateway is powered on
The gateway has no power input
or power supply is abnormal
Off
Slow Flashing
Flashing
Link (Green)
Speed
PWR
RUN
FXS
WAN/LAN
The gateway is running properly
SIP account is registered successfully
The gateway is running improperly
FXS port is currently occupied by a call
FXS port is idle or faulty
The gateway is properly connected to network
The gateway is not connected to network
or network connection is improper
Work at 100Mbps
Work at 10Mbps
Fast Flashing
Model
Port Type
DAG2000-16S
LAN RJ11 RJ21
0 0
0
0
0
0
0
416
24
32
4
4
2
2
1
2
2
3
2
0
0
03
DAG2000-24S
DAG2000-32S
DAG2500-48S
DAG2500-64S
DAG2500-72S
RJ45
28
40 0 DAG3000-112S
Dinstar’s VoIP gateways have three types of FXS ports, namely RJ11,RJ21 and RJ45. For the
number of ports of each model,please refer to the table above.

Indicators & Interfaces
3
DAG2000-16S
DAG2000-24S/32S
Power Indicator
Power Switch
Power Switch
Power Jack LAN Ports
LAN Ports
Console Port
Reset Button
Ground Point
Ground Point
Running Indicator
Power Indicator
Running Indicator
Telephone In-use Indicator FXS Ports 0-15
FXS Ports 0-31 (RJ11)
FXS Ports (RJ21)
Note: The position of each indicator and interface of DAG2000-24S is the same as on the
DAG2000-32S.
Reset Button
Telephone In-use Indicator
Power Jack
Console Port

DAG2500-48S/64S/72S
DAG3000-112S
Power Indicator
Running Indicator
Alarm Indicator
Network Link Indicator Telephone In-use Indicator
Power Switch
Screw
Telephone In-use
Indicators Power Indicator
Running Indicator
FXS Ports
Power Switch
Ground Point
Power Jack Switch for Master/Slave Power (Reserved)
LAN Ports
Console Port
User board
User Board Main Control Board
Power Jack Console Port
Reset Button FXS Ports(RJ21)
Note: The position of each indicator and interface of DAG2500-48S and DAG2500-64S is the
same as on DAG2000-72S.
Ground Point LAN Ports
Reset Button

Installation Attentions
4
Installation Instructions
5
Connection Diagram for DAG2000-16S
Connect gateway with network via a switch
Network Cable
Switch
RJ11 telephone line
Telephone
PC
Connect FXS ports with analog phones
Connect gateway with power input and ground point
100-240V AC
Grounding Cable
Ground Point
Network Cable
Please check the FXS type of your gateway before installation:
DAG2000-16S is equipped with RJ11 ports;
DAG2000-24S/32S is equipped with both RJ11 and RJ21 ports;
DAG2500-48S/64S72S is equipped with RJ21 ports;
DAG3000-112S is equipped with RJ45 ports.
For the wire sequence of RJ21 and RJ45,please refer to Section 6 Wire Sequence of this manual.
Anti-jamming: to reduce the interference with telephone calls, it’s highly recommended that telephone
lines connected to the gateway should be placed away from power cables;
Power supply: the gateway accepts AC input voltage of 100-240V. Please ensure safe and stable power
supply;
Network bandwidth:please ensure there is enough network bandwidth so as to guarantee stabilized
running of the gateway；
Ventilation: to avoid overheating, please do not pile up the gateway with other devices and make sure the
gateway has good ventilation around.
Temperature and humidity: to avoid any accident that might cause malfunction , it’s advised to install the
gateway in an equipment room where temperature and humidity are appropriate ；
Mechanical load: please make sure the gateway is placed steadily to avoid damage. It’ s highly advised to
horizontally place the gateway on a flat surface or a cabinet.

Connection Diagram forDAG2000-24S/32S
Connect gateway with network via a switch
Type 2: Connect FXS ports with analog phones
Type 1: Connect FXS ports with analog phones
Connect gateway with power input and ground point
Network Cable
Network Cable
Switch
Telephone
Telephpne
RJ11 Cable(Telephone Line)
RJ21 Cable
PC
100-240V AC
Grounding Cable
Ground Point

Connection Diagram for DAG2500-48S/64S/72S
Connect gateway with network via a switch
Network Cable
Network Cable
Switch
PC
Connect FXS ports with analog phones
Telephone
RJ21 Cable
Connect gateway with power input and ground point
100-240V AC
Grounding Cable
Gound Point

Connection Diagram for DAG3000-112S
Connect gateway with network via a switch
Network Cable
Switch
PC
Connect FXS ports with analog phones
Telephone
RJ45 Cable
Power Connection & Grounding
100-240V AC
Grounding
Cable
Ground
Point
Network Cable

RJ45 & RJ21 Wire Sequence
6
·RJ45 Wire Sequence
Both DAG2000-24S/32S and DAG2500-48S/64S/72S have RJ21 interface as FXS port.
One RJ21 cable has 25 pairs of wires, with the 25th pair of wires vacant. That means
one RJ21 interface outputs 24 calls.
.
DAG3000-112S is equipped with RJ45 interface as FXS port. One RJ45 cable can output
four calls.The internal wire sequence of RJ45 cable is shown as follows:
·RJ21 Wire Sequence
Call No.
Colour
PIN No.
White
P1
0
Blue
P26
1 2 34
White Orange White Green White Brown White Slate
P2
P27 P3 P28 P4 P29 P5 P30
Call No.
Colour
PIN No.
Red
P6
5
Blue
P31
68 9
Orange Green Brown Slate
P7 P32 P8
P33 P9 P34
P10
P35
7
Red Red Red Red
Call No.
Colour
PIN No.
Black
P11
10
Blue
P36
11 12 13 14
Orange Green Brown Slate
P12 P37 P13 P38 P14
P39
P15
P40
Black Black Black Black
Call No.
Colour
PIN No.
Yellow
P16
15
Blue
P41
16 17 18 19
Orange Green Brown Slate
P17
P42
P18
P43 P19 P44 P20 P45
Yellow Yellow Yellow Yellow
Call No.
20
21 22
23 24
Colour Violet Blue Orange Green Brown Slate
Violet Violet Violet Violet
PIN No.
P21
P46
P22
P47 P23 P48 P24 P49 P25
P50
Pair 1
Pair 2
Pair 3
Pair 4
Orange & White
Orange
Green & White
Green
Blue& White
Blue
Brown & White
Brown
1
2
3
4
5
6
7
8

Modify PC’s IP Address
7
Log in Web Management System
8
To log in the Web Management System of the gateway, you need to modify the IP address
of PC first to make it at the same network segment with the gateway.
On the PC, click ‘Network (or Ethernet) → Properties’.
Double-click ‘Internet Protocol Version 4 (TCP/IPv4)’.
Select ‘Use the following IP address’, and then enter an available IP address
‘192.168.11.XXX’ which is at the same network segment with ‘192.168.11.1’.
1
2
3
Open a web browser and enter the gateway’s IP address (default IP is 192.168.11.1).
Then input username and password in the displayed login GUI. Both the default
username and password are admin.。

Modify Gateway’s IP Address
9
Configure Gateway
10
Click Save and then restart the gateway for the new configurations to take effect.
(1) Configure SIP Server
(2) Configure SIP Account Information
If you want to modify the IP address of the gateway, please click ‘Network → Local
Network’ in the navigation tree on the left of the Web Management System, and then
input new IP address and DNS server address on the displayed interface.
Log in the Web Management System of the gateway, and then click SIP Server in the
navigation tree and then enter the address of the SIP server which is to be registered.
Click Save in the last.
Click Port in the navigation tree on the left, and then click Add. Input the SIP account and
authentication password assigned by the SIP server.

Basic Operations
11
More Details
12
Honest, Concentrated, Innovative, Open
Dinstar Technologies Co., Ltd
Website: http://www.dinstar.com
Facebook: http://www.facebook.com/dinstarvoip/
This document only provides instructions for quick installation and basic configuration,
For detailed configuration and parameter explanation, please refer to user manual or
ask for online technical support.
Dial *158# to query the IP address of LAN port of the gateway;
Dial *159# to query the IP address of WAN port of the gateway;
Dial *114# to query the telephone number of a FXS port;
Dial *165*000000# to restore default IP address, username and password;
Restore factory default settings:
(1) dial *166*000000#;
(2) press the RST button for 7 seconds;
(3) Log in the gateway and then click ‘Tools → Factory Reset’,then click Apply
and restart the gateway.
Restart the gateway:
(1) Dial *111# to restart the gateway.
(2) Log in Web Management System, click “Tools” in the navigation tree on
the left, and then click “Restart”on the displayed interface.