Directed Directechs DS3 User manual

DS3+ / DS4+ 933.NISS14
v1.04.195.3
2022 Mitsubishi Outlander (Smart Key)

Introduction 3
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Pre-Installation Module Programming Test 6
Activating 8-Channel Gateway 7
Wiring diagram 8
Locating components in the vehicle 9
Vehicle connections 10
Module programming 13
For Security-Only and Convenience-Only programming, see next sections. 13
Module programming for convenience only (skip transponder) 14
Pairing remotes 15
Connecting the module 15
8556T Temperature Sensor 15
8504D Combo Sensor 15
RF Systems 15
When used in conjunction with SmartStart 16
D2D port configuration 16
Manual transmission 17
LED diagnostics and troubleshooting 18
Soft reset 20
Hard reset 20
Tach learning procedure (not needed with Virtual Tach) 21
Initializing Virtual Tach (not needed with hardwired or data tach applications) 21
Limited lifetime consumer warranty 22
Quick Reference Guide (customer copy) 23
Contents

3933.NISS14 1.04.195.3 2022 Mitsubishi Outlander (Smart Key)
©2022 VOXX•DEI LLC. All rights reserved.
Introduction
This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a
digital configuration require the module to be flashed with vehicle specific firmware. Refer to our website (www.directechs.com) and click on
the DIRECTLINK text in the header for additional information.
DS3/DS3+ and DS4/DS4+ modules provide an all-in-one solution for most modern vehicles, and include remote start, keyless entry, security,
and immobilizer bypass capabilities. T-harnesses may also be used in many applications for easy installation.
The following methods are available to configure modules:
• Web: www.directechs.com (DS3/DS3+ and DS4/DS4+)
• Desktop Application: Directlink DT (DS3/DS3+ and DS4/DS4+)
• Mobile Device: Directlink App (DS4/DS4+ only)
When Flashing via Directlink DT (Desktop app) or via the Web, an XKloader2 will be required.
To configure via Web or DirectLink DT (mobile app):
1. Disconnect the main module from any (+) 12V power source.
2. Connect the module to your computer using the XKLoader2.
3. Follow the steps in the pop-up window that will be displayed when the module is detected.
Notes:
•Flashing via web is only possible using Internet Explorer on Windows 8, 8.1, and 10.
•This method is not compatible with any other browser (Edge, Chrome, Firefox, etc.)
•When using Windows 11 or newer, Directlink DT is mandatory.
The DS4/DS4+ module is designed to be configured using the DirectLink application through mobile devices.
To download the DirectLink mobile application, visit the Google Play or Apple store. They can also be
configured via Web and DirectLink DT. The DS4/DS4+ features are built in Bluetooth® 4.0, allowing you to
configure and control your system. The DS3/DS3+ module is not equipped with Bluetooth®, therefore is not
compatible with the DirectLink app for mobile devices.
To configure via DirectLink DT (mobile app):
1. Follow and complete the wiring diagram(s) related to your installation through the app.
2. When installation is complete, select Configure DS4/DS4+.
3. Follow the on-screen instructions.
FLASH REQUIRED!
FLASH REQUIRED!
4 White

4933.NISS14 1.04.195.3 2022 Mitsubishi Outlander (Smart Key)
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.
Parking Lights Control
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Trunk / Hatch Release
Control of aftermarket alarm with OEM remote
Fuel level/EV battery level
Key2GO
* Odometer
Immobilizer Bypass-Data No Key Req'd
RAP Shut Down (Retained ACC Power)
Remote Start Takeover
SmartStart
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Brake Status (foot brake)
Door Locks Status
E-Brake Status
Ignition Status

5933.NISS14 1.04.195.3 2022 Mitsubishi Outlander (Smart Key)
©2022 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
START HERE This section highlights important information for this specific firmware and will assist in pricing accordingly, as
well as bringing awareness to any operational or vehicle limitations.
Compatibilities and Requirements
T-Harness
compatible T-Harness is not compatible.
AUX
Keys required for
programming 1Keys required for operation 0
Vehicle Takeover Refer to the Quick Reference Guide section for more details.
Firmware notes
8-Channel Gateway: This firmware requires the vehicle's 8-Channel Gateway status to be Enabled. Before proceeding with
the complete installation, a pre-installation & module programming test is required. If the test is unsuccessful, you must have the
8-Channel Gateway enabled by the Nissan dealer. See the "Pre-Installation Module Programming Test" section fro more details.
Unlock and Unlock all: For driver priority unlock or unlock all, this feature must be selected in the vehicle's settings menu by the user.
Autolights: Shutdown time will depend on the vehicle's setting selected by the user.
Remote start: All vehicle doors must be closed and vehicle must be locked for the remote start to be operational.
Fuses: It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each wiring
diagram.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector..
Refer to the "Vehicle connections" following the installation diagram.
Footnotes
[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory
hood pin, or if not supported in data
[2] Siren: The siren is only required when enabling the security features during module flashing.
[3] Security-only installations: refer to the "Locating components in the vehicle" section for optional starter disable
connection
[4] Hazards light: This connection is optional but is required for vehicles without autolights. It is also required for shutdown
diagnostics and/or hybrid system installations as well as using CAR FINDER.
[5] Power liftgate: This connection is only required if equipped with power liftgate. Doors must be unlocked for proper
operation of the power liftgate.

6933.NISS14 1.04.195.3 2022 Mitsubishi Outlander (Smart Key)
©2022 VOXX•DEI LLC. All rights reserved.
22 8
12
HS CAN Low: Tan : 1
HS CAN High: Tan/Black: 2
HS CAN 2 Low: Orange/Brown: 3
HS CAN 2 High: Orange/Green: 4
HS CAN Low: Lavender/Pink, pin 27
HS CAN High: Lavender/Blue, pin 26
HS CAN 2 Low: White, pin 14 (+) 12V: Green, pin 16
HS CAN 2 High: Blue, pin 6
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
20 19 18 17 16 15 14 13 12 11 10 8
97 6 54321
16
8
9
1
OBDII
Diagnostic
(black conn.)
(-) Ground:
Black, pin 4
BCM
(gray conn. behind
dash fusebox)
(+) 12V Input: Red: 6 & 12
(-) Ground: Black: 10
BCM
(behind
dash fuse box)
All connections
are mandatory.
4 2442
Slide to open
A module can also be used for
this installation.
IMPORTANT:
Position the
fuses correctly!
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
15
15
Module Programming Test
Pre-Installation Module Programming Test
To test your module, make the connections as shown on the wiring diagram below. When the connections are done, refer to the following section to program your module.
Ensure vehicle is in a safe location and cannot move forward during programming. For vehicles
equipped with a manual transmission, make sure the gearshift is in the neutral position.
Connect the remaining harnesses to the module.
Press the Push-to-Start (PTS) button once (1) to turn the ignition on.
The LED will quickly flashe orange and turn green for one second, then slowly flashe orange.
1
Connect the 12-pin main power harness to the module.
DS3+: Wait until the LED turns ON solid red then proceed to the next step.
DS4+: The LED turns ON solid blue for 1 second to confirm Bluetooth communication.
Wait until the LED turns ON solid red, then proceed to the next step.
2
3
4
This Firmware requires the vehicles "8-Channel Gateway" to be Enabled. Before proceeding with the complete install, it is recommended that the following test is performed.
If the test programming is unsuccessful, you must have the gateway enabled by the Nissan dealer.
If the LED slowly flashes orange, you can proceed with a full installation as your vehicle does not require scan tool modifications from the
Nissan dealer. However, if the LED flashes red 3 times, you must visit the Nissan dealer and have them enable the “8-Channel Gateway.”
Please refer to the “Activating 8-Channel Gateway” section for additional details.
Note: If you are unable to have the vehicle return to the Nissan dealer, or they are unwilling to make the changes, you may use the
NISS13 Firmware, which will require a "Key-Wrap" installation.

7933.NISS14 1.04.195.3 2022 Mitsubishi Outlander (Smart Key)
©2022 VOXX•DEI LLC. All rights reserved.
Activating 8-Channel Gateway
Note: If the Pre-Installation Module Programming Test was successful, skip this page
and proceed with the full installation.
To set the 8-Channel Gateway to Open Mode:
1. Click .
A new page will appear with a CGW Information tab, and a
Restricted Mode tab directly under it.
2. In the bottom right corner of the screen, click to change the
status from Restricted to Open.
A new page will appear requesting your credentials.
3. Enter your credentials and click Submit/Soumettre.
A new page will appear as the system changes the status from
Restricted Mode to Open Mode. The circle next to CGW
Information will be green instead of red.
You are now able to program your module.
Note: Print this page for the customer for them to bring it to the
dealership, in order for them to follow the proper steps.

8933.NISS14 1.04.195.3 2022 Mitsubishi Outlander (Smart Key)
©2022 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Wiring diagram
(-) Ground: Black: 10
(+) Brake Output: White: 5 & 11
HS CAN Low: Tan : 1
(-) Hazards Output: Lt. Blue/Black: 10
HS CAN High: Tan/Black: 2
HS CAN 2 Low: Orange/Brown: 3
HS CAN 2 High: Orange/Green: 4
(+) 12V Input: Red: 6 & 12
Smart Key Interrupt (veh. side): Lt. Green: 8
Smart Key Interrupt (conn. side): Lt. Green/White: 9
(-) Hood Input: Gray: 21
Siren
(+) Siren Output: Brown/Red: 11
(-) GWA Output: Blue/White: 2
(-) Trunk Release Output: Red/White: 4
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
22 812
4 2442
Slide to open
A module can also be used for
this installation.
IMPORTANT:
Position the
fuses correctly!
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
15
15
HS CAN Low: Lavender/Pink, pin 27
HS CAN High: Lavender/Blue, pin 26
(+) Brake: Lt. Green, pin 6
(-) Hazards: Lavender/Yellow, pin 13
BCM
(gray conn.
behind dash fusebox)
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
20 19 18 17 16 15 14 13 12 11 10 8
97 6 54321
Hood Pin
18 1524 20 16 1322 1921 17 1423
6312 8 4 110 79 5 211
BCM
(black conn.
behind dash fusebox)
(-) Power Liftgate:
Lt. Green, pin 3
Power Liftgate Switch
(gray conn.)
4321
Smart Key Interrupt:
Lavender/Pink, pin 6
Dash fuse box
(white conn. rear of fusebox)
7 456
16 131415
1
32
CUT
1112 9 810
BCM
(behind
dash fuse box)
Refer to the Optional starter
disable connection section for
relay and connection details.
HS CAN 2 Low:
White, pin 14 (+) 12V: Green,pin 16
HS CAN 2 High: Blue, pin 6
16
8
9
1
OBDII
Diagnostic
(black conn.)
(-) Ground: Black, pin 4

9933.NISS14 1.04.195.3 2022 Mitsubishi Outlander (Smart Key)
©2022 VOXX•DEI LLC. All rights reserved.
Locating components in the vehicle
Optional starter disable connection
When using an external relay, use a 1N4002 diode or larger.
22 812
4 2442
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
(-) Ground When Armed (GWA) Output: Blue/White: 2
86 85
30
87a
87
Cut
Starter (conn. side)
Starter (veh. side)
(+) Ignition
Refer to the
Vehicle connections
section for wire and
connector details.
1A diode [1N4002+ ]
Important: When flashing your module for Security Only, the Ground When Armed (GWA)
function is pre-configured. When flashing your module for Remote Start & Security, you must
manually assign the designated output to Anti Grind (AG) Starter Kill.
(Applicable to CORE 194+.)

10 933.NISS14 1.04.195.3 2022 Mitsubishi Outlander (Smart Key)
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2022 Mitsubishi Outlander (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes.
Data harness, 8-pin white connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H1/1 Tan (Data) HS CAN Low 1 BCM behind dash fuse box, gray 40 pin plug, pin 27 Data Lavender/Pink Mandatory
H1/2 Tan/Black (Data) HS CAN High 1 BCM behind dash fuse box, gray 40 pin plug, pin 26 Data Lavender/Blue Mandatory
H1/3 Orange/Brown (Data) HS CAN Low 2 OBD-Data Link Connector, black 16 pin plug, pin 14 Data White (DIAG CAN) Mandatory
H1/4 Orange/Green (Data) HS CAN High 2 OBD-Data Link Connector, black 16 pin plug, pin 6 Data Blue (DIAG CAN) Mandatory
H1/5 Lt. Green No Connection No Connection
H1/6 Violet/Brown No Connection No Connection
H1/7 Orange/Black No Connection No Connection
H1/8 Yellow/Black No Connection No Connection
Analog input/output harness, 22-pin white connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/1 Lt. Green/Black No Connection No Connection
H2/2 Blue/White (-) Ground When Armed (GWA) Output [3] Starter:
BCM behind dash fuse box, black 24 pin plug, pin 19
Ignition:
BCM behind dash fuse box, black 24 pin plug, pin 1
Remote Starter
Must use a 1N4002 diode or larger.
-
-
Red
Lavender/Yellow
Security Only
H2/3 Dk. Green/Black (-) Lock Output No Connection
H2/4 Red/White (-) Trunk Output [5] Power Liftgate Switch, gray 4 pin plug, pin 3 - Lt. Green Optional
H2/5 Brown/Black (-) Horn Output Horn Switch-Clock Spring, black 16 pin plug, pin 10 - Blue Optional
H2/6 Brown/White (-) AUX 1 Output No Connection
H2/7 White (+) AUX 1 Output No Connection
H2/8 Violet/Black (-) AUX 2 Output No Connection
H2/9 Dk. Blue/Black (-) Unlock Output No Connection
H2/10 Lt. Blue/Black (-) Hazard Light Output [4] BCM behind dash fuse box, gray 40 pin plug, pin 13 - Lavender/Yellow Mandatory
H2/11 Brown/Red (+) Siren Output [2] Security Only
H2/12 Pink (+) Ignition Sense Input No Connection
H2/13 Violet (+) Door Input No Connection
H2/14 Brown (+) Brake Input No Connection
H2/15 White/Blue (-) Activation Input No Connection
H2/16 Red/Blue No Connection No Connection
H2/17 Black/White (-) E-Brake Input No Connection
H2/18 Orange/Black (+) Instant Alarm Input No Connection