Directed Xpresskit DBALL2 User manual

® Hyundai is a registered trademark and property of its respective company.
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle
completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to
start the vehicle from a distance.
SmartStart Compatible
SmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote
Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more
information.
Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Vehicle Application Guide...................................................................................................................................................
Installation (Wiring Diagram & Vehicle Wiring Reference Chart)
Type 1.................................................................................................................................................................................
Type 2.................................................................................................................................................................................
SmartStart/XL202 Installation Notes..................................................................................................................................
Programming
Module Programming.........................................................................................................................................................
Module Reset.....................................................................................................................................................................
Hard Reset.........................................................................................................................................................................
Feature & Option List..........................................................................................................................................................
Feature Programming.........................................................................................................................................................
LED Diagnostics & Troubleshooting...................................................................................................................................
Parking Light Error Codes..................................................................................................................................................
Limited One-Year Consumer Warranty...............................................................................................................................
Quick Reference Guide......................................................................................................................................................
02
03
05
07
08
09
09
11
11
12
14
15
16
Index
This guide supports the installation of a DBALL2 in Remote Start Ready (RSR) mode. This solution
offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF
Kit or SmartStart (all sold separately).
Rev.: 20161206
Platform: DBALL2
Firmware: HYUNDAI9 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Note: This firmware does not support pitstop/idle mode.

Vehicle Application Guide Page 2
Rev.: 20161206
Platform: DBALL2
Firmware: HYUNDAI9 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Vehicles
2017 2016 PK-Immobilizer Bypass-Data No Key Req'd AV-Parking Lights Control DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release RS-3x LOCK START (Start control using OEM Remote) RS-3x LOCK STOP (Stop control using OEM Remote) RS-RAP Shut Down (Retained ACC Power) RS-Remote Start Ready RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-Door Locks Status ST-Ignition Status
Hyundai
Tucson (Smart Key) 21•••••••••••••••••••••
Legend:
PK: Transponder & Immobilizer Override
AV: Horn & Lights Controls
DL: OE Door Lock & Alarm Controls
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
The following table lists the vehicles and features which are compatible with this product. The number assigned to each
year allows you to determine which installation type should be used for your vehicle.

Rev.: 20161206
Platform: DBALL2
Firmware: HYUNDAI9 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
FT CAN High: Orange/Green: 5
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 3
FT CAN Low: Orange/Brown: 6
(MUX) Parking Lights Output: Violet/Brown: 9
EMS COM: Orange/Black: 11
(+) Accessory Output: Gray: 6
(+) Starter Output: Gray/Black: 7
(+) 12V: Red: 13
(-) Ground: Black: 14
Diagnostic Connector
OBDII (connector side view)
1 8
169
C-CAN High: Green, pin 6
C-CAN Low: Orange, pin 14
Smart Key Ign. Interrupt (conn. side): Orange/Red: 10
Smart Key Ign. Interrupt (veh.side): Yellow/Red: 11
3
1
MC11 Junction
(Gray conn. at driver kick panel)
10
37 29 22 18
11
38 30 23 19
12
39 31 20
1721
36 28
1
2
3
4
5
6
7
8
9
13
14
15
16
4
5
6
7
32
33
34
35
40
41
42
43
44
45
46
47
48
(+)Starter:
Red/Black,
pin 31
EMS COM:
Blue, pin 20
30
86 85
87
87a
(MUX) Parking Lights:
Yellow, pin 14
Headlight/Wiper switch
(Black conn. at steering column)
1 3 5 72 4 68
9 11 13 1510 12 14 16
Smart Key Ignition Interrupt
Green, pin 6 CUT
B-CAN High:
Green/Black, pin 3
B-CAN Low:
Blue/Black, pin 4
12345678910
11 12 18
17
13 14 15 16
I/P-F Fusebox/Smart Junction Box
(White conn. rear of
fusebox/Smart Junction Box)
Required for
vehicle takeover
(+) Ignition: Blue, pin 36
(-) Ignition Output: Black/White: 1
(+) Accessory: Green, pin 28
30
86 85
87
87a
31
41 11
2
3
4
1
5
6
7
8
9
10
19
20
39
40
14
15
17
18
16
34
35
37
38
36
24
25
27
28
26
12
13
22
23
32
33
21
29
30 I/P-A Fusebox/Smart Junction Box
(White conn. front of
fusebox/smart junction box)
(+) 12V:
White,
pin 31
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Fuse
30A
Installation Type 1 Page 3
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL2
RF
Prog. Button
LED
4
14 12 2
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
Hood Pin
Remote Start Safety
Override Switch
6: White/Black,(-) Hood
Note: Hood pin only required
on vehicles not equipped
with a factory hood pin.

Rev.: 20161206
Platform: DBALL2
Firmware: HYUNDAI9 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Page 4
Type 1 - Vehicle Wiring Reference Chart
MC11 Gray 48-pin conn.
(located in driver kick panel)
10
37 29 22 18
11
38 30 23 19
12
39 31 20
1721
36 28
1
2
3
4
5
6
7
8
9
13
14
15
16
4
5
6
7
32
33
34
35
40
41
42
43
44
45
46
47
48
M01 Black16-pin conn.
(at Headlight/Wiper Switch)
1 3 5 72 4 6 8
9 11 13 1510 12 14 16
I/P-F White 18-pin conn.
(located rear of fusebox
/ Smart Junction Box)
12345678910
11 12 18
17
13 14 15 16
Function Color Pin Polarity Location Color Pins
C-CAN High Green 6 Data OBDII diagnostic connector White 16
C-CAN Low Orange 14 Data OBDII diagnostic connector White 16
(MUX) Parking Lights Yellow 14 (+) M01 located at Headlight/Wiper Switch White 16
B-CAN High Green/Black 3 Data I/P-F located at Rear of Fusebox/Smart Junction Box White 18
B-CAN Low Blue/Black 4 Data I/P-F located at Rear of Fusebox/Smart Junction Box White 18
12V White 31 (+) I/P-A located at Front of Dash Fusebox White 41
Accessory Green 28 (+) MC11 located in Driver's kick panel Gray 48
Ignition Blue 36 (+) MC11 located in Driver's kick panel Gray 48
Starter Red/Black 31 (+) MC11 located in Driver's kick panel Gray 48
EMS COM Blue 20 Data MC11 located in Driver's kick panel Gray 48
Wire Information Connector Information
Hyundai Tucson (Smart Key) 2016
I/P-A White 41-pin conn.
(located front of fusebox)
Front of Fusebox
31
41 11
2
3
4
1
5
6
7
8
9
10
19
20
39
40
14
15
17
18
16
34
35
37
38
36
24
25
27
28
26
12
13
22
23
32
33
21
29
30

Rev.: 20161206
Platform: DBALL2
Firmware: HYUNDAI9 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
FT CAN High: Orange/Green: 5
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 3
FT CAN Low: Orange/Brown: 6
(MUX) Parking Lights Output: Violet/Brown: 9
EMS COM: Orange/Black: 11
(+) Accessory Output: Gray: 6
(+) Starter Output: Gray/Black: 7
(+) 12V: Red: 13
(-) Ground: Black: 14
Diagnostic Connector
OBDII (connector side view)
1 8
169
C-CAN High: Green, pin 6
C-CAN Low: Orange, pin 14
Smart Key Ign. Interrupt (conn. side): Orange/Red: 10
Smart Key Ign. Interrupt (veh.side): Yellow/Red: 11
3
1
30
86 85
87
87a
(MUX) Parking Lights:
Yellow, pin 14
Headlight/Wiper switch
(Black conn. at steering column)
1 3 5 72 4 68
9 11 13 1510 12 14 16
Smart Key Ignition Interrupt
Green, pin 6 CUT
B-CAN High:
Green/Black, pin 3
B-CAN Low:
Blue/Black, pin 4
12345678910
11 12 18
17
13 14 15 16
I/P-F Fusebox/Smart Junction Box
(White conn. rear of
fusebox/Smart Junction Box)
Required for
vehicle takeover
(-) Ignition Output: Black/White: 1
30
86 85
87
87a
31
41 11
2
3
4
1
5
6
7
8
9
10
19
20
39
40
14
15
17
18
16
34
35
37
38
36
24
25
27
28
26
12
13
22
23
32
33
21
29
30 I/P-A Fusebox/Smart Junction Box
(White conn. front of
fusebox/smart junction box)
(+) 12V:
White,
pin 31
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Fuse
30A
42 1
831
25 19
1235
1033
27 21
1437
16
2228
39
932
26 20
1336
1134
1538
17
2329
40
44 3
46 5
43 2
45 4
47
41 2430 18
6
48 7
(+) Starter:
Red/Black,
pin 45
EMS COM: Blue, pin 3
MC11 Junction
(Blue conn. at
driver kick panel)
(+) Accessory:
Green, pin 30
(+) Ignition:
Blue, pin 41
Installation Type 2 Page 5
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL2
RF
Prog. Button
LED
4
14 12 2
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
Hood Pin
Remote Start Safety
Override Switch
6: White/Black,(-) Hood
Note: Hood pin only required
on vehicles not equipped
with a factory hood pin.

Rev.: 20161206
Platform: DBALL2
Firmware: HYUNDAI9 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Type 2 - Vehicle Wiring Reference Chart
M01 Black16-pin conn.
(at Headlight/Wiper Switch)
1 3 5 72 4 6 8
9 11 13 1510 12 14 16
I/P-F White 18-pin conn.
(located rear of fusebox
/ Smart Junction Box)
12345678910
11 12 18
17
13 14 15 16
Function Color Pin Polarity Location Color Pins
C-CAN High Green 6 Data OBDII. White 16
C-CAN Low Orange 14 Data OBDII. White 16
(MUX) Parking Lights Yellow 14 MUX Headlight/Wiper switch. Black 16
B-CAN High Green/Black 3 Data I/P-F Rear of Fusebox/Smart Junction Box. White 18
B-CAN Low Blue/Black 4 Data I/P-F Rear of Fusebox/Smart Junction Box. White 18
12V White 31 (+) I/P-A Front of Fusebox/Smart Junction Box. White 41
Accessory Green 30 (+) MC11 Driver's kick panel. Blue 48
Ignition Blue 41 (+) MC11 Driver's kick panel. Blue 48
Starter Red/Black 45 (+) MC11 Driver's kick panel. Blue 48
EMS COM Blue 3 Data MC11 Driver's kick panel. Blue 48
Wire Information Connector Information
Hyundai Tucson (Smart Key) 2017
I/P-A White 41-pin conn.
(located front of fusebox)
Front of Fusebox
31
41 11
2
3
4
1
5
6
7
8
9
10
19
20
39
40
14
15
17
18
16
34
35
37
38
36
24
25
27
28
26
12
13
22
23
32
33
21
29
30
42 1
831
25 19
1235
1033
27 21
1437
16
2228
39
932
26 20
1336
1134
1538
17
2329
40
44 3
46 5
43 2
45 4
47
41 2430 18
6
48 7
MC11 Junction
(Blue conn. at driver kick panel)
Page 6

The optional XL202 and antenna are not included and MUST be purchased separately.
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
4
4
XL202
Antenna
XOVER
SmartStart is optional and not included. It MUST be purchased separately.
SmartStart is optional and not included. It MUST be purchased separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
5 pins
D2D (4 pins, white)
4 pins
2 pins,
not used
CABLE
CABLE
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL2 package.
2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
SmartStart/XL202 Installation Notes
SmartStart Revision B
RF Kit
RF Kit & PKE Combination
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
RF Kit, PKE & SmartStart BT Combination
SmartStart Revision A
DBALL2
DBALL2
DBALL2
LED
Prog.
Button
D2D (4 pins, white)
4 pins
2 pins,
not used
OR
SmartStart
Configuration Wires (White & Brown or Blue)
Cut Brown or Blue Loop
LED
THIS SIDE UP
LED
Page 7
Rev.: 20161206
Platform: DBALL2
Firmware: HYUNDAI9 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
The DBALL2 Remote Start Ready (RSR) solution offers three (3) configuration options to control your system: 3x OEM
Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation
information for SmartStart and XL202.

Module Programming
Page 8
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
Rev.: 20161206
Platform: DBALL2
Firmware: HYUNDAI9 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
2
Important: Do NOT press the brake pedal. Make sure the
key is inside the vehicle.
Press the Push-to-Start (PTS) button twice to turn the
ignition ON.
Key Inside
the Vehicle
HOLD
Do NOT
depress the
brake pedal
2X ENGINE
START
STOP
PUSH
1
10-pin
D2D
st
1
12-pin
14-pin
nd
2
rd
3
&
Solid
Connect the 10-pin, 12-pin and 14-pin harnesses to
DBALL2, then wait until the LED turns ON solid red.
NOTE: To skip the transponder programming and use convenience features only press
the programming button 5 times. The LED will turn orange then proceed to step 2.
Go to the next page to complete the module programming.
Important
10-pin
D2D
XL202
10-pin
D2D
SmartStart
OR
The DBALL module must be disconnected from any power source before SmartStart can
be connected to it. Failing to do so could damage DBALL.
a. To ensure that the D2D communication between SmartStart and DBALL works properly, the
Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue
loop must be cut (Rev A SmartStart).
b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the DBALL D2D connector.
Connect SmartStart to DBALL using the D2D port.
SmartStart Installation
Connect XL202 to DBALL using the D2D port.
XL202 Installation
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and
function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest
version of the application.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
When the flashing operation is successful, you can proceed with the programming instructions below.
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the Config for RSR button.
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select FLASH YOUR MODULE and follow the on screen
instructions.

Rev.: 20161206
Platform: DBALL2
Firmware: HYUNDAI9 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
3
The orange LED flashes then the green LED turns ON for 3
seconds and shuts off.
Note: When skipping transponder programming, the orange
LED flashes then the orange LED turns ON for 3 seconds
and shuts off.
&&
Green or orange
3 seconds
Flash
orange Off
&
You have successfully completed the module programming sequence.
4Press the Push-to-Start (PTS) button once more to turn on the ignition OFF. 1X ENGINE
START
STOP
PUSH
Module Programming
Page 9

1If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
10-pin
D2D
st
1
12-pin
14-pin
nd
2
th
4
rd
3
Warning Against Executing a Hard Reset!
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such
as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
2
Solid
&
Release
3 Release the programming button. The LED turns ON solid red.
Module Reset
Hard Reset
2& &
1
Wait 3 seconds until the LED turns ON solid orange then release the
programming button. The LED turns ON solid red.
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
10-pin
D2D
st
1
12-pin
14-pin
nd
2
th
4
rd
3
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed
to the module using the web config tool will not be affected.
Page 10
Solid Release Solid
Solid Flashes
&
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds
until the LED starts to flash orange and red.
Rev.: 20161206
Platform: DBALL2
Firmware: HYUNDAI9 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.