Directed Xpresskit DBALL2 User manual

Vehicle Application Guide................................................................................................................................................
Key2GO...........................................................................................................................................................................
Installation
Without T-Harness...........................................................................................................................................................
With T-Harness THCHD3................................................................................................................................................
Programming
Module Programming......................................................................................................................................................
Key2GO Programming....................................................................................................................................................
Module Reset & Hard Reset............................................................................................................................................
Feature & Option List.......................................................................................................................................................
Feature Programming......................................................................................................................................................
LED Diagnostics and Troubleshooting............................................................................................................................
Limited One-Year Consumer Warranty............................................................................................................................
Quick Reference Guide...................................................................................................................................................
02
02
03
04
05
06
07
08
09
10
11
12
Index
Installation Guide
Update Alert: Firmware updates are posted to the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Platform: DBALL2
Firmware: CHRYSLER6
© 2015 Directed. All rights reserved.
Rev.: 20151029
® Dodge is a registered trademark and property of its company.
RAM
Door lock and transponder interface compatible with the 2013-2016 Dodge Ram (key type). Some of
the available feature include: transponder override, door lock control, factory security control, trunk
release, tach sensing, as well as door, hood and trunk sensing.
The optional Plug & Play T-Harness THCHD3 (sold separately) provides simpler and faster installation.
Key2GO is required.

Platform: DBALL2
Firmware: CHRYSLER6
© 2015 Directed. All rights reserved.
Rev.: 20151029
Vehicle Application Guide
Page 2
The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more
information on installation wiring, programming and troubleshooting for these vehicles.
This feature is mandatory to control the immobilizer override in this firmware.
Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses
an array of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to
give up a key.
The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.
All Key2GO-compatible firmware are clearly indicated in the function list of each vehicle search result page and will also
appear on the flash page. Any first-time user must re-register to gain access to Key2GO, and some additional information
will be required to complete the registration process, such as your Directed account number and store name.
Key2GO is compatible with XpressVIP 4.5 or higher and requires an XKLoader.
Refer to page 5 of this guide for instructions on how to program features using Key2GO.
Vehicles
2015 2015 2014 2013 PK-Immobilizer Bypass-Data No Key Req'd AV-Panic Mode Activation AV-Parking Lights Control DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock FOB-Control of aftermarket alarm with OEM remote Key2GO RS-OEM Remote Start Activation using XL-202 or RF kit RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-E-Brake Status ST-Ignition Status
Dodge/Ram
1500 • • • • • • • • • • • • D • D • • D • • • W
2500 • • • • • • • • • • • • D • D • • D • • • W
3500 • • • • • • • • • • • • D • D • • D • • • W
Legend:
•: D2D & Wire-to-Wire (W2W) PK: Transponder & Immobilizer Override
D: Data-to-Data (D2D) only AV: Horn & Lights Controls
W: Wire-to-Wire (W2W) DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w/ FOB Rem ote
RS: Rem ote Start & Engine Controls
SS: Integrated Security & Monitoring

Platform: DBALL2
Firmware: CHRYSLER6
© 2015 Directed. All rights reserved.
Rev.: 20151029
Page 3
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
Remote
Starter
(-) GWR (Status)
(-) Lock Output
(+) Starter Output
(+) Parking Light Output
(-) Unlock Output
(+) Brake Input
(-) E-Brake Status Input
(+) Ignition Input
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
(+) Brake Output: Gray: 6
(MUX) Parking Light Output: Violet/Brown: 9
(+) Ignition Output: Gray/Black: 7
(-) E-Brake Output: Black/White: 1
(-) RAP Off: Orange/Black: 11
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
[1] (-) (AC) Tach Output: Violet/White: 5
(+) 12 V
(-) Ground
Immo. Data (veh.side): Yellow/Black: 10
Immo. Data (veh.side): Orange/Yellow: 9
(+) 12V: Brown/Red: 12
Immo. Data (conn. side): Yellow: 8
Ignition Status Output: Yellow/Red: 11
1
4
48
24
38
11
25
5
10
43
9
39
42
(-) Ground: Black: 14(-) Ground
(+) 12V: Red, pin 3
(+) 12V: Red: 13
(+) 12V
BCM
(Connector B)
12
3
4
1 8
169
CAN C High: Gray/White, pin 6
CAN C Low:
Yellow, pin 14
OBDII
Diagnostic Connector
(-) Driver Door Trigger: Violet, pin 9
BCM
(White Connector F)
Parking Lights Input: White/Brown, pin 20
BCM
(Blue Connector G)
1
2
3
4
5
6
7
8
91011
12
24 131415
1617
18
1920212223
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
8: Violet: (+) Starter Input
7: Pink/White: (+) Parking Light Input
10: Blue/White: (-) GWR (Status) Input
TX
(-) Ground
RX
(+)12V
10
DBALL2
RF
Prog.Button
LED
4
14 12 2
P#: XKD2D65
9: Pink: (+) Ignition Input
123456
Immo. Data:
White/Lt Green: pin 5
(+) 5V Ignition:
Violet/Brown,
pin 4
Ignition Node
(black connector)
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Installation without T-Harness
[2] DBALL2 Only. Required for heated seats.
[2] HS CAN2 Low: Orange/Brown: 6
[2] HS CAN2 High: Orange/Green: 5
[2] CAN IHS High: Gray, pin 3
[2] CAN IHS Low
White, pin 11
Note: The BCM is located in the driver side dash, above the kick panel.
(-) Hood Input
(-) Hood Status Output: Blue/Red: 12

Platform: DBALL2
Firmware: CHRYSLER6
© 2015 Directed. All rights reserved.
Rev.: 20151029
Installation with T-Harness THCHD3
OBDII
Diagnostic 16-pin Connector
Keyless
Ignition Node
Keyless
Ignition Node
T-02:
Dodge RAM 1500
Only
OR
OR
These T-Harness connectors are
NOT interchangeable. They will fit
ONLY the appropriate vehicles.
T-01
6-pin Black
Connector
Remote Start Safety
Override Switch
10
DBALL2
RF
Prog.Button
LED
4
14 12 2
(MUX) Parking Lights Output: Violet/Brown
(-) RAP Off: Orange/Black
Remote
Starter
(+) Ignition Input
(+) 12 V
THCHD3 Rev. 1
(Optional T-Harness)
(+)Ignition Output: Yellow/Red
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Page 4
[1] (AC) Tach Input
[1] (-) (AC) Tach Output: Violet/White
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
(+) 12V:
Red, pin 3
BCM
(Connector B)
12
3
4
1
4
48
24
38
11
25
5
10
43
9
39
42
(-) Driver Door Trigger:
Violet, pin 9
BCM
(White Connector F)
BCM
(Blue Connector G)
Parking Lights:
White/Brown, pin 20
1
2
3
4
5
6
7
8
9
10
11
12
24 131415
1617
18
1920212223
Note: The BCM is located in the driver
side dash, above the kick panel.
OBDII

Platform: DBALL2
Firmware: CHRYSLER6
© 2015 Directed. All rights reserved.
Rev.: 20151029
Module Programming Page 5
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
Disconnect the module and complete the Key2GO programming.
Go to the next page for Key2GO programming.
Turn the key to ignition position, then back
to OFF position two (2) times.The LED
flashes orange slowly. &
Flashes Slowly
Key OUT
OFF
START
IGN
Key IN
OFF
START
ON
2
3
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit
available functions and features.
1. Connect the interface module to your computer using the XKLoader.
2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware
that is currently saved on the interface module will be indicated in the top right corner of the page.
3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.
4. In the search result page, select Flash Standard install, and follow the instructions provided on the screen.
5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.
6. The following message will be displayed when the upload is completed:
“The flashing is successfully completed. You may now unplug the kit.”
You can now proceed with the programming instructions below.
1
Solid
Wait until the LED turns ON solid red.
Note: To skip the transponder programming and use convenience features
only, press the programming button 5 times.
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to
the module, then connect the 4-pin D2D harness.
D2D Installation
W2W Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the
module, then connect the 14-pin harness to the module.
10-pin
D2D
st
1
12-pin
14-pin
nd
2
rd
3
10-pin
D2D
st
1
th
4
12-pin
14-pin
nd
2
rd
3
x 2 &