Directed DIRECTECHS CHRYSLER3 User manual

CHRYSLER3
INSTALLATION GUIDE
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.
2020-01-16
© 2020 Directed, Vista CA
Directed Digital
Solutions
Designed by Installers for Installers

Contents
Warning! Safety first ....................................................................................................................... 3
Introduction .................................................................................................................................... 4
Pre-installation and application warnings ..................................................................................... 4
Vehicle application guide........................................................................................................... 5
Wiring connections ......................................................................................................................... 6
Main power harness (H1), 12-pin thick gauge connector ............................................................... 6
Auxiliary output harness (H2), 16-pin black connector ................................................................... 6
Analog harness (H3), 18-pin white connector ............................................................................... 7
MC501 harness (H4), 8 thick-gauge wires (optional)..................................................................... 7
Installation (wiring diagrams & vehicle wiring reference charts) ............................................................ 8
Type 1 with T-Harness (THCHC3 Rev. 1 & 2) ................................................................................ 8
Type 1 ..................................................................................................................................... 9
Type 2 with T-Harness (THCHC3 Rev. 1 & 2) .............................................................................. 12
Type 2 ................................................................................................................................... 13
Type 3 with T-Harness (THCHC3 Rev. 2)..................................................................................... 16
Type 3 ................................................................................................................................... 17
Type 4 with T-Harness (THCHC3 Rev. 2)..................................................................................... 19
Type 4 ................................................................................................................................... 20
Type 5 with T-Harness (THCHC3 Rev. 2)..................................................................................... 23
Type 5 ................................................................................................................................... 24
Type 6 with T-Harness (THCHC3 Rev. 2)..................................................................................... 26
Type 6 ................................................................................................................................... 27
Type 7 with T-Harness (THCHC3 Rev. 2)..................................................................................... 29
Type 7 ................................................................................................................................... 30
Connecting the module .................................................................................................................. 32
Important! .............................................................................................................................. 32
Manual or automatic transmission selection ................................................................................ 32
Optional sensors ..................................................................................................................... 33
RF Systems ............................................................................................................................. 33
When used in conjunction with SmartStart.................................................................................. 33
Module programming.............................................................................................................. 34
LED diagnostics and troubleshooting.......................................................................................... 35
Soft reset................................................................................................................................ 37
Hard reset .............................................................................................................................. 37
Learning the Tach (not needed with Virtual Tach) ............................................................................... 38
Initializing Virtual Tach (not needed with hardwired or data tach applications) ..................................... 38
Limited lifetime consumer warranty .................................................................................................. 39
Quick Reference Guide.................................................................................................................. 40

Warning! Safety first
The following safety warnings must be observed at all times:
• Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.
• When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never
operate the system in an area that does not have adequate ventilation.
The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:
• Never use a test light or logic probe when installing this unit. Always use a multimeter.
• Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).
• When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must
be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from
children all remote controls to assure that the system does not unintentionally remote start the vehicle.
• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.
ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE
STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.
Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or
death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with
the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the
neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.
This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product
installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem
immediately.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF
OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE
OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE
START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the
installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged
parking brake. Do not allow anyone to stand in front of or behind the vehicle.
This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such
vehicles may pose certain risk.
3Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Introduction
The CHRYSLER3 firmware for Directed Digital Solutions is compatible with specific Chrysler, Dodge/RAM
and Jeep vehicles. It is a complete solution for remote start, security (if applicable), bypass interface, and
convenience. This guide provides information on the installation of the module using CHRYSLER3. If you would
prefer using this system as a digital solution, go to www.directechs.com and search for the make, model and
year of the vehicle. This will allow you to find the proper firmware and corresponding installation guide.
Warning! This module can only be programmed via the web tool, which can be found on www.directechs.com or using the
Directechs Mobile application for mobile devices. Features and functions will become accessible when you connect the module
using the XKLoader.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible THCHC3 Rev. 1 & 2 Keys required for programming 1Keys required for operation 0
The optional Plug & Play THCHC3 Rev. 1 & 2 T-Harnesses are sold separately.
The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed.
Key2GO is mandatory to control the immobilizer override in this firmware.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic
connector.
Refer to the "Vehicle wiring reference chart" following each installation type.
General notes: This section highlights important information for this specific firmware.
[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin.
[2] The siren is ONLY required when enabling the security features during module flashing.
[3] Features will ONLY function if vehicle is equipped with OEM touchscreen radio package.
[4] The following cars are ONLY compatible with optional T-Harness THCHC3 Rev. 2:
2018 Chrysler 300/300C (Smart Key)
2018 Dodge/Ram 1500 (Smart Key)
2018 Dodge/Ram 2500 (Smart Key)
2018 Dodge/Ram 3500 (Smart Key)
2018 Dodge Challenger (Smart Key)
2018 Dodge Charger (Smart Key)
2018-2019 Dodge Durango (Smart Key)
2018-2019 Dodge Journey (Smart Key)
2018-2019 Jeep Grand Cherokee (Smart Key)
Additional parts required (maximum required):
6A Diode
0 x 1A Diodes 86 85
30
87a
87
0 x Relay
Resistor 100Ω
0 x Resistor
Fuse 7.5A
0 x Fuse
4Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Vehicle application guide
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year
allows you to determine which installation type should be used for your vehicle.
Vehicles
2020 2019 2018 2017 2016 2015 2014 2013 2012 2011
PK-Immobilizer Bypass-Data No Key Req'd AV-Parking Lights Control CC-Heated Seats Activation CC-Rear Window Defogger Activation DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote Key2GO
Chrysler
300/300c (Smart Key) 61111111••••••••••••
Dodge/Ram 20 19 18 17 16 15 14 13 12 11
1500 (Smart Key) 422222 ••••••••• ••
2500 (Smart Key) 422222 ••••••••• ••
3500 (Smart Key) 422222 ••••••••• ••
Challenger (Smart Key) 5111 ••••••••••••
Charger (Smart Key) 51111111••••••••••••
Durango (Smart Key) 441111 ••••••••• ••
Journey (Smart Key) 4 4 1 1 1 1 1 1 1 • • • • • • • • • • •
Jeep 20 19 18 17 16 15 14 13 12 11
Grand Cherokee (Smart Key) 7732222 ••••••••••••
Legend:
AV: Horn & Light Controls
CC: Comfort & Convenience Controls
DL: OE Door Lock & Alarm Controls
5Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Wiring connections
The wiring connections listed below are specific to this firmware.
Main power harness (H1), 12-pin thick gauge connector
Conn./Pin Color Description
H1/1 White Relay 3 COM – No Connection 1
H1/2 White/Brown Relay 3 N.O. – No Connection 1
H1/3 Brown/Red Relay 2 N.O. – No Connection
H1/4 Yellow/Red Relay 2 COM – No Connection
H1/5 Orange/Red Relay 2 N.C. – No Connection
H1/6 Yellow Relay 1 COM – (+) Immobilizer Data Interrupt (connector side) 1
H1/7 White Relay 3 COM – No Connection 1
H1/8 White/Brown Relay 3 N.O. – No Connection 1
H1/9 Black (-) Ground
H1/10 Red (+) 12 Volt (Battery)
H1/11 Orange/Yellow Relay 1 N.C. – Immobilizer Data Interrupt (vehicle side) 1
H1/12 Brown Relay 1 N.O. – No Connection 1
Auxiliary output harness (H2), 16-pin black connector
Conn./Pin Color Description
H2/1 Violet/Brown (MUX) Parking Lights Output
H2/2 Yellow/Black Immobilizer Data (vehicle side)
H2/3 Orange/Black No Connection
H2/4 Tan HS CAN Low
H2/5 Tan/Black HS CAN High
H2/6 Light Green No Connection
H2/7 Orange/Green HS CAN2 High
H2/8 Orange/Brown HS CAN2 Low
H2/9 Violet/Green No Connection
H2/10 Green/Black No Connection 2
H2/11 White/Violet No Connection 2
H2/12 White/Red No Connection 2
H2/13 Lt. Blue/Black No Connection 2
H2/14 Green/Red (+) Push-to-Start Output 2
H2/15 N/A No Connection
H2/16 Violet/Yellow No Connection
1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.
2. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay
may be necessary.
6Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Analog harness (H3), 18-pin white connector
Conn./Pin Color Description
H3/1 Lt. Blue/Red No Connection
H3/2 Black/White (-) Parking Brake Input (Manual Transmission) 2
H3/3 Gray (-) Hood Input 2
H3/4 N/A No Connection
H3/5 Gray/Black (+) Glow Plug Input 2
H3/6 Violet/White (AC) Tach Input 2
H3/7 Dark Blue No Connection 1
H3/8 Brown/Black (-) Horn 1
H3/9 Red/White No Connection 1
H3/10 White/Green (-) Door Input 2
H3/11 Yellow/Green (+) Door Input 2
H3/12 Blue/Red No Connection
H3/13 Light Blue (-) Trunk Trigger Input 2
H3/14 Pink/Yellow (-) Activation (Start Trigger) Input
H3/15 Dark Green No Connection 1
H3/16 Brown/White (+) Brake Input 2
H3/17 Brown (+) Siren Output 1
H3/18 Blue/White (-) Ground When Running (Status) Output 1
MC501 harness (H4), 8 thick-gauge wires (optional)
Conn./Pin Color Description
H4/1 Pink/White No Connection
H4/2 Red/White No Connection
H4/3 Pink No Connection
H4/4 Red No Connection
H4/5 Orange No Connection
H4/6 Red No Connection
H4/7 Green No Connection
H4/8 Violet No Connection
1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay
may be necessary.
2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a
list of compatible features.
7Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Installation (wiring diagrams & vehicle wiring reference charts)
Type 1 with T-Harness (THCHC3 Rev. 1 & 2)
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).
(MUX) Parking Light Output:
Violet/Brown
Parking Light (MUX):
Pin 3
12 3 456
Headlight connector
(black connector at
Headlight Switch)
Do not cut the loops
For Rev. 2 ONLY
Siren
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
Hood Pin
The Remote
Start Safety
Override
Switch MUST
be in the ON
position.
THCHC3 Rev. 1 & 2 (Optional T-Harness)
12-pin
White
Connector
16-pin
Black
Connector
2-pin
Black
Connector
Keyless Ignition Node
(black connector
at PTS switch)
6-pin
Connectors
Male
Connect T-Harness
male connector
into PTS switch
male
Female
T-01 T-02
Male
Female Not Used
male male
male
female
OR
OBDII
Diagnostic Connector
Use the style of OBDll
connector that fits the best.
8Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Type 1
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).
9: Black: (-) Ground
10: Red: (+) 12V Input
(MUX) Parking Lights Output: Violet/Brown: 1
Hood Pin
(+) PTS Output: Green/Red: 14
6: Yellow: Immo. Data
Interrupt (conn. side)
11: Orange/Yellow: Immo. Data
Interrupt (veh. side)
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
Keyless Ignition Node
(black connector at PTS switch)
(+) PTS: Violet/Lt.Blue or Violet/Brown, pin 4
Immo. Data:
White/Lt. Green,
pin 5
Immo. Data (veh. side): Yellow/Black: 2
HS CAN2 High: Orange/Green: 7
HS CAN2 Low: Orange/Brown: 8
CAN C High:
Gray/White, pin 6
CAN IHS Low:
White, pin 11
OBDII
Diagnostic Connector
CAN C Low:
Yellow, pin 14
CAN IHS High:
Gray, pin 3
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
(+) 12V: Red or
Red/Yellow, pin 3
Siren
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
Parking Light (MUX): Pin 3
123456
Headlight connector
(black connector at
headlight switch)
Plug (B)
(black connector at BCM
in passenger kick panel)
CUT
9Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Chrysler 300/300c (Smart Key) 2011-2017
CAN C High Gray/White 6 Data OBDII diagnostic connector. Black 16 A
CAN C Low Yellow 14 Data OBDII diagnostic connector. Black 16 A
CAN IHS High Gray 3 Data OBDII diagnostic connector. Black 16 A
CAN IHS Low White 11 Data OBDII diagnostic connector. Black 16 A
Immo. Data White/Lt. Green 5 Data Keyless ignition node (Start/Stop button). Black 6 B
PTS Violet/Lt. Blue 4 (+) Keyless ignition node (Start/Stop button). Black 6 B
Parking Light White/Brown 3 MUX Headlight switch. Black 6 C
12V Red/Yellow 3 (+) BCM above passenger kick, pin plug (B). Black 4 D
Dodge Challenger (Smart Key) 2015-2017
CAN C High Gray/White 6 Data OBDII diagnostic connector. Black 16 A
CAN C Low Yellow 14 Data OBDII diagnostic connector. Black 16 A
CAN IHS High Gray 3 Data OBDII diagnostic connector. Black 16 A
CAN IHS Low White 11 Data OBDII diagnostic connector. Black 16 A
Immo. Data White/Lt. Green 5 Data Keyless ignition node (Start/Stop button). Black 6 B
PTS Violet/Lt. Blue 4 (+) Keyless ignition node (Start/Stop button). Black 6 B
Parking Light White/Brown or White 3 MUX Headlight switch. Black 6 C
12V Red/Yellow 3 (+) BCM above passenger kick, pin plug (B). Black 4 D
Dodge Charger (Smart Key) 2011-2017
CAN C High Gray/White 6 Data OBDII diagnostic connector. Black 16 A
CAN C Low Yellow 14 Data OBDII diagnostic connector. Black 16 A
CAN IHS High Gray 3 Data OBDII diagnostic connector. Black 16 A
CAN IHS Low White 11 Data OBDII diagnostic connector. Black 16 A
Immo. Data White/Lt. Green 5 Data Keyless ignition node (Start/Stop button). Black 6 B
PTS Violet/Lt. Blue 4 (+) Keyless ignition node (Start/Stop button). Black 6 B
Parking Light White/Brown 3 MUX Headlight switch. Black 6 C
12V Red or Red/Yellow 3 (+) BCM above passenger kick, pin plug (B). Black 4 D
10 Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Dodge Durango (Smart Key) 2014-2017
CAN C High Gray/White 6 Data OBDII diagnostic connector. Black 16 A
CAN C Low Yellow 14 Data OBDII diagnostic connector. Black 16 A
CAN IHS High Gray 3 Data OBDII diagnostic connector. Black 16 A
CAN IHS Low White 11 Data OBDII diagnostic connector. Black 16 A
Immo. Data White/Lt. Green 5 Data Keyless ignition node (Start/Stop button). Black 6 B
PTS Violet/Brown 4 (+) Keyless ignition node (Start/Stop button). Black 6 B
Parking Light White/Lt.Green 3 MUX Headlight switch. Black 6 C
12V Red 3 (+) BCM above passenger kick, pin plug (B). Black 4 D
Dodge Journey (Smart Key) 2011-2017
CAN C High Gray/White 6 Data OBDII diagnostic connector. Black 16 A
CAN C Low Yellow 14 Data OBDII diagnostic connector. Black 16 A
CAN IHS High Gray 3 Data OBDII diagnostic connector. Black 16 A
CAN IHS Low White 11 Data OBDII diagnostic connector. Black 16 A
Immo. Data White/Lt. Green 5 Data Keyless ignition node (Start/Stop button). Black 6 B
PTS Violet/Lt. Blue 4 (+) Keyless ignition node (Start/Stop button). Black 6 B
Parking Light White/Brown 3 MUX Headlight switch. Black 6 C
12V Red or Red/Yellow 3 (+) BCM above passenger kick, pin plug (B). Gray 4 D
11 Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Type 2 with T-Harness (THCHC3 Rev. 1 & 2)
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).
Do not cut the loops
For Rev. 2 ONLY
Siren
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
(MUX) Parking Light Output:
Violet/Brown
Hood Pin
The Remote
Start Safety
Override
Switch MUST
be in the ON
position.
12-pin
White
Connector
16-pin
Black
Connector
2-pin
Black
Connector
Keyless Ignition Node
(black connector
at PTS switch)
6-pin
Connectors
Male
Connect T-Harness
male connector
into PTS switch
male
Female
T-01 T-02
Male
Female Not Used
THCHC3 Rev. 1 & 2 (Optional T-Harness)
male male
male
female
OR
OBDII
Diagnostic Connector
Use the style of OBDll
connector that fits the best.
Parking Light (MUX):
White Lt.Green or White/Brown,
pin 1
2 3 541
7 8 1096
Headlight connector
(black connector at
Headlight Switch)
12 Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Type 2
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).
9: Black: (-) Ground
10: Red: (+) 12V Input
(MUX) Parking Lights Output: Violet/Brown: 1
Hood Pin
(+) PTS Output: Green/Red: 14
6: Yellow: Immo. Data
Interrupt (conn. side)
11: Orange/Yellow: Immo. Data
Interrupt (veh. side)
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
Keyless Ignition Node
(black connector at PTS switch)
(+) PTS: Violet/Brown, pin 4
Immo. Data:
White/Lt. Green,
pin 5
Plug (B)
(black connector at BCM
in driver or passenger kick panel)
Immo. Data (veh. side): Yellow/Black: 2
HS CAN2 High: Orange/Green: 7
HS CAN2 Low: Orange/Brown: 8
CAN C High:
Gray/White, pin 6
CAN IHS Low:
White, pin 11
OBDII
Diagnostic Connector
CAN C Low:
Yellow, pin 14
CAN IHS High:
Gray, pin 3
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
(+) 12V: Red, pin 3
Siren
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
CUT
Parking Light (MUX):
White Lt.Green
or White/Brown,
pin 1
2 3 541
7 8 1096
Headlight connector
(black connector at
Headlight Switch)
13 Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Dodge/RAM 1500 (Smart Key) 2013-2017
CAN C High Gray/White 6 Data OBDII diagnostic connector. Black 16 A
CAN C Low Yellow 14 Data OBDII diagnostic connector. Black 16 A
CAN IHS High Gray 3 Data OBDII diagnostic connector. Black 16 A
CAN IHS Low White 11 Data OBDII diagnostic connector. Black 16 A
Immo. Data White/Lt. Green 5 Data Keyless ignition node (Start/Stop button). Black 6 B
PTS Violet/Brown 4 (+) Keyless ignition node (Start/Stop button). Black 6 B
Parking Light White/Brown 1 MUX Headlight switch. Black 10 C
12V Red 3 (+) BCM under driver dash, pin plug (B). Black 4 D
Dodge/RAM 2500 (Smart Key) 2013-2017
CAN C High Gray/White 6 Data OBDII diagnostic connector. Black 16 A
CAN C Low Yellow 14 Data OBDII diagnostic connector. Black 16 A
CAN IHS High Gray 3 Data OBDII diagnostic connector. Black 16 A
CAN IHS Low White 11 Data OBDII diagnostic connector. Black 16 A
Immo. Data White/Lt. Green 5 Data Keyless ignition node (Start/Stop button). Black 6 B
PTS Violet/Brown 4 (+) Keyless ignition node (Start/Stop button). Black 6 B
Parking Light White/Brown 1 MUX Headlight switch. Black 10 C
12V Red 3 (+) BCM above passenger kick, pin plug (B). Black 4 E
Dodge/RAM 3500 (Smart Key) 2013-2017
CAN C High Gray/White 6 Data OBDII diagnostic connector. Black 16 A
CAN C Low Yellow 14 Data OBDII diagnostic connector. Black 16 A
CAN IHS High Gray 3 Data OBDII diagnostic connector. Black 16 A
CAN IHS Low White 11 Data OBDII diagnostic connector. Black 16 A
Immo. Data White/Lt. Green 5 Data Keyless ignition node (Start/Stop button). Black 6 B
PTS Violet/Brown 4 (+) Keyless ignition node (Start/Stop button). Black 6 B
Parking Light White/Brown 1 MUX Headlight switch. Black 10 C
12V Red 3 (+) BCM above passenger kick, pin plug (B). Black 4 E
14 Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Jeep Grand Cherokee (Smart Key) 2014-2017
CAN C High Gray/White 6 Data OBDII diagnostic connector. Black 16 A
CAN C Low Yellow 14 Data OBDII diagnostic connector. Black 16 A
CAN IHS High Gray 3 Data OBDII diagnostic connector. Black 16 A
CAN IHS Low White 11 Data OBDII diagnostic connector. Black 16 A
Immo. Data White/Lt. Green 5 Data Keyless ignition node (Start/Stop button). Black 6 B
PTS Violet/Brown 4 (+) Keyless ignition node (Start/Stop button). Black 6 B
Parking Light White Lt. Green or
White/Brown 1 MUX Headlight switch. Black 10 C
12V Red 3 (+) BCM above passenger kick, pin plug (B). Black 4 E
15 Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Type 3 with T-Harness (THCHC3 Rev. 2)
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).
Cut ALL 4
CAN Loops
Siren
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
Hood Pin
The Remote
Start Safety
Override
Switch MUST
be in the ON
position.
12-pin
White
Connector
16-pin
Black
Connector
2-pin
Black
Connector
Keyless Ignition Node
(black connector
at PTS switch)
6-pin
Connectors
Male
Connect T-Harness
male connector
into PTS switch
male
Female
T-01 T-02
Male
Female Not Used
THCHC3 Rev. 2 (Optional T-Harness)
29
18
26
28
3941
59
42 40 32 27 19 1
31
52
53
47
46
HS CAN High: Tan/Black
HS CAN Low: Tan
HS CAN2 High: Orange/Green
HS CAN2 Low: Orange/Brown
CAN C Low: Yellow, pin 53
CAN IHS Low: White, pin 47
CAN C High: Blue, pin 52
CAN IHS High: Brown, pin 46
i5010 Junction Connector
(black connector high
in drivers kick panel)
(MUX) Parking Light Output: Violet/Brown
Parking Light
(MUX):
White/Brown,
pin 1
2 3 541
7 8 1096
Headlight connector
(black connector at
Headlight Switch)
male male
male
female
OR
OBDII
Diagnostic Connector
Use the style of OBDll
connector that fits the best.
16 Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Type 3
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).
9: Black: (-) Ground
10: Red: (+) 12V Input
(MUX) Parking Light Output: Violet/Brown: 1
Hood Pin
(+) PTS output: Green/Red: 14
6: Yellow: Immo. Data
Interrupt (conn. side)
11: Orange/Yellow: Immo. Data
Interrupt (veh. side)
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
Keyless
Ignition Node
(black connector at PTS switch)
(+) PTS: Violet/Brown, pin 4
Immo. Data:
White/Lt. Green, pin 5
Plug (B)
(black connector at BCM
above passenger kick panel)
Immo. Data (veh. side): Yellow/Black: 2
HS CAN2 High: Orange/Green: 7
HS CAN2 Low: Orange/Brown: 8 The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
(+) 12V: Red, pin 3
Siren
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
Headlight connector
(black connector at
Headlight Switch)
Parking Light (MUX):
White/Brown, pin 1
2 3 541
7 8 1096
CUT
29
18
26
28
3941
59
42 40 32 27 19 1
31
52
53
47
46
CAN C Low: Yellow, pin 53
CAN IHS Low: White, pin 47
CAN C High: Blue, pin 52
CAN IHS High: Brown, pin 46
i5010 Junction Connector
(black connector high
in drivers kick panel)
17 Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Jeep Grand Cherokee (Smart Key) 2018
CAN C High Blue 52 Data Junction connector high in drivers kick panel, Plug (I5010). Black 59 A
CAN C Low Yellow 53 Data Junction connector high in drivers kick panel, Plug (I5010). Black 59 A
CAN IHS High Brown 46 Data Junction connector high in drivers kick panel, Plug (I5010). Black 59 A
CAN IHS Low White 47 Data Junction connector high in drivers kick panel, Plug (I5010). Black 59 A
Immo. Data White/Lt. Green 5 Data Keyless ignition node (Start/Stop button). Black 6 B
PTS Violet/Brown 4 (+) Keyless ignition node (Start/Stop button). Black 6 B
Parking Light White/Brown 1 MUX Headlight switch. Black 10 C
12V Red 3 (+) BCM above passenger kick, pin plug (B). Black 4 D
18 Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Type 4 with T-Harness (THCHC3 Rev. 2)
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).
Cut ALL 4
CAN Loops
Siren
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
Hood Pin
The Remote
Start Safety
Override
Switch MUST
be in the ON
position.
12-pin
White
Connector
16-pin
Black
Connector
2-pin
Black
Connector
Keyless Ignition Node
(black connector
at PTS switch)
6-pin
Connectors
Male
Connect T-Harness
male connector
into PTS switch
male
Female
T-01 T-02
Male
Female Not Used
THCHC3 Rev. 2 (optional T-Harness)
HS CAN High: Tan/Black
HS CAN Low: Tan
HS CAN2 High: Orange/Green
HS CAN2 Low: Orange/Brown
(MUX) Parking Light Output: Violet/Brown
CAN C High: White/Green
or Lt.Green, pin 1
CAN Junction
(white connector
in green junction)
CAN C Low: White/Blue
or Yellow, pin 2
CAN IHS Low:
White/Orange or
White, pin 2
CAN Junction
(green or black connector
in white or brown junction)
CAN IHS High: Pin 1
male male
male
female
OR
OBDII
Diagnostic Connector
Use the style of OBDll
connector that fits the best.
Refer to the Vehicle Wiring
Reference Chart for wire and
connector details related to the
standard connections in the vehicle.
19 Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.

Type 4
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).
9: Black: (-) Ground
10: Red: (+) 12V Input
(MUX) Parking Light Output: Violet/Brown: 1
Hood Pin
(+) PTS Output: Green/Red: 14
6: Yellow: Immo. Data
Interrupt (conn. side)
11: Orange/Yellow: Immo. Data
Interrupt (veh. side)
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
Keyless Ignition Node
(black connector at PTS switch)
(+) PTS: Violet/Brown or Violet/Blue, pin 4Immo. Data:
White/Lt. Green,
pin 5
Plug (B)
(black connector at BCM
in driver or above passenger kick panel)
Immo. Data (veh. side): Yellow/Black: 2
HS CAN2 High: Orange/Green: 7
HS CAN2 Low: Orange/Brown: 8
CAN C High: White/Green
or Lt.Green, pin 1
CAN IHS Low:
White/Orange or
White, pin 2
CAN Junction
(white connector
in green junction)
CAN Junction
(green or black connector in white or brown junction)
CAN C Low: White/Blue
or Yellow, pin 2
CAN IHS High: Pin 1
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
(+) 12V: Red, pin 3
Siren
(-) Hood Input: Gray: 3
(+) Siren Output: Brown: 17
CUT
Refer to the Vehicle Wiring
Reference Chart for wire and
connector details related to the
standard connections in the vehicle.
20 Directed Digital Solutions CHRYSLER3
© 2020-01-16 Directed. All rights reserved.