Directed Directechs DS3 User manual

Designed by Installers for Installers
INSTALLATION GUIDE
DS3+ / DS4+
2010 Chrysler Sebring Convertible. 933.CHRYSLER 7.34.195.3
© 2022 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.

Introduction 3
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Installation 6
Wiring diagram with T-Harness (THCHN2) 6
Wiring diagram 7
Locating components in the vehicle 8
Vehicle connections 9
Module programming 12
Key-Type vehicles 12
Push-to-Start (PTS) vehicles 14
Module programming for security-only installations 16
Pairing remotes 17
Connecting the module 17
8556T Temperature Sensor 17
8504D Combo Sensor 17
RF Systems 17
When used in conjunction with SmartStart 18
D2D port configuration 18
Manual transmission 19
LED diagnostics and troubleshooting 20
Soft reset 22
Hard reset 22
Tach learning procedure (not needed with Virtual Tach) 23
Initializing Virtual Tach (not needed with hardwired or data tach applications) 23
Limited lifetime consumer warranty 24
Quick reference guide 25
Contents

3933.CHRYSLER 7.34.195.3 2010 Chrysler Sebring Convertible
©2022 VOXX•DEI LLC. All rights reserved.
Introduction
This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a
digital configuration require the module to be flashed with vehicle specific firmware. Refer to our website (www.directechs.com) and click on
the DIRECTLINK text in the header for additional information.
DS3/DS3+ and DS4/DS4+ modules provide an all-in-one solution for most modern vehicles, and include remote start, keyless entry, security,
and immobilizer bypass capabilities. T-harnesses may also be used in many applications for easy installation.
The following methods are available to configure modules:
• Web: www.directechs.com (DS3/DS3+ and DS4/DS4+)
• Desktop Application: Directlink DT (DS3/DS3+ and DS4/DS4+)
• Mobile Device: Directlink App (DS4/DS4+ only)
When Flashing via Directlink DT (Desktop app) or via the Web, an XKloader2 will be required.
To configure via Web or DirectLink DT (mobile app):
1. Disconnect the main module from any (+) 12V power source.
2. Connect the module to your computer using the XKLoader2.
3. Follow the steps in the pop-up window that will be displayed when the module is detected.
Notes:
•Flashing via web is only possible using Internet Explorer on Windows 8, 8.1, and 10.
•This method is not compatible with any other browser (Edge, Chrome, Firefox, etc.)
•When using Windows 11 or newer, Directlink DT is mandatory.
The DS4/DS4+ module is designed to be configured using the DirectLink application through mobile devices.
To download the DirectLink mobile application, visit the Google Play or Apple store. They can also be
configured via Web and DirectLink DT. The DS4/DS4+ features are built in Bluetooth® 4.0, allowing you to
configure and control your system. The DS3/DS3+ module is not equipped with Bluetooth®, therefore is not
compatible with the DirectLink app for mobile devices.
To configure via DirectLink DT (mobile app):
1. Follow and complete the wiring diagram(s) related to your installation through the app.
2. When installation is complete, select Configure DS4/DS4+.
3. Follow the on-screen instructions.
FLASH REQUIRED!
FLASH REQUIRED!
4 White

4933.CHRYSLER 7.34.195.3 2010 Chrysler Sebring Convertible
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.
Parking Lights Control
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Control of aftermarket alarm with OEM remote
* Fuel Level
Immobilizer Bypass-Data No Key Req'd
3x LOCK START (Start control using OEM Remote)
3x LOCK STOP (Stop control using OEM Remote)
Accessory Activation
Ignition Activation
RAP Shut Down (Retained ACC Power)
Remote Start Takeover
SmartStart
Start (Crank) Activation
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Brake Status (foot brake)
E-Brake Status
Ignition Status

5933.CHRYSLER 7.34.195.3 2010 Chrysler Sebring Convertible
©2022 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible THCHN2 Keys required for programming 1Keys required for operation 0
The optional Plug & Play THCHN2 T-Harness is sold separately.
Important! All T-Harness wires NOT listed in the diagram are NOT required for the installation. Loose wires such as Siren
Output and Hood Input may need to be pulled from the tapped section of the T-Harness. Refer to the "Wiring diagram with
T-Harness" for more information on connections and installation instructions.
The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed.
All T-Harness wires NOT listed in the diagram are NOT required for the installation.
All connectors are displayed from the wire side (unless specified otherwise).
It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each
wiring diagram.
Refer to the "Vehicle connections" following the installation diagram.
General notes: This section highlights important information for this specific firmware.
[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin.
[2] The siren is ONLY required when enabling the security features during module flashing.
[3] The Green wire is ONLY required for starter disable and antigrind appplications
[4] When using an external relay, use a 1N4002 diode or larger.

6933.CHRYSLER 7.34.195.3 2010 Chrysler Sebring Convertible
©2022 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Refer to the
“Vehicle connections” section
for wire and connector details.
Siren
Hood Pin
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
16
8
9
1Diagnostic
Connector OBDII
(connector side view)
CAN C Low: Pin 14
CAN C High: Pin 6
Sentry Key Module
(black 8-pin conn.)
To vehicle
male 8-pin connector
at the ignition switch To 8-pin Female Connector
at the ignition switch
(+) Parking Light Output: White
(-) RAP Off Output: Yellow/Black
HS CAN High: Orange/Green
HS CAN Low: Orange/Brown
THCHN2
(Optional T-Harness)
Wiring diagram with T-Harness (THCHN2)
86 85
30
87a
87
15A Fuse (+) 12V Input
(-) Drivers Door Trigger
(+) Parking Lights Output
WARNING: Due to optional t-harness
current limitations, a relay is required
for (+) Parking Lights.
8-pin White Connector
12-pin Black Connector
1A diode [1N4002+ ]
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
22 812
4 2442
Slide to open
A module can also be used for
this installation.
IMPORTANT:
Position the
fuses correctly!
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
15
15
(-) GWA Output: Red/White: 4
Refer to the Optional
starter disable connection
section for relay and
connection details.

7933.CHRYSLER 7.34.195.3 2010 Chrysler Sebring Convertible
©2022 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
(-) Ground: Black: 10
HS CAN 1 Low: Tan: 1
(MUX) Ignition Output: Violet/Brown: 6
HS CAN 1 High: Tan/Black: 2
(-) RAP Off Output: Yellow/Black: 8
(+) 12V Input: Red: 6 & 12
(+) 12V Input: Blue/Red: 2
(+) Ignition Output: Blue: 3
(+) Parking Light Output: White: 5 & 11
HS CAN 2 Low: Orange/Brown: 3
HS CAN 2 High: Orange/Green: 4
(-) Ground: Black or Black/Striped, pin 4
(+) Ignition: Pink or Pink/White, pin 3
(MUX) Ignition: Violet/Brown, pin 1
Sentry Key Module
(black 8-pin conn.,
connector side view)
1 8
Refer to the
“Vehicle connections” section
for wire and connector details.
16
8
9
1Diagnostic
Connector OBDII
(connector side view)
Wiring diagram
Hood Pin
(-) Hood Input: Gray: 21
Siren
(+) Siren Output: Brown/Red: 11
(-) GWA Output: Red/White: 4
Refer to the Optional starter
disable connection section for
relay and connection details.
CAN B High: White/Orange, pin 6
CAN B Low: White or White/Pink, pin 7
CAN C Low: Orange or
White/ Dk. Blue, pin 14
CAN C High: Green
or White/ Lt. Blue, pin 6
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
22 812
4 2442
Slide to open
A module can also be used for
this installation.
IMPORTANT:
Position the
fuses correctly!
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
15
15

8933.CHRYSLER 7.34.195.3 2010 Chrysler Sebring Convertible
©2022 VOXX•DEI LLC. All rights reserved.
Locating components in the vehicle
(-) Ground When Armed (GWA) Output: Red/White: 4
86 85
30
87a
87
Optional starter disable connection
Cut
Starter (conn. side)
Starter (veh. side)
(+) Ignition
Refer to the
Vehicle connections
section for wire and
connector details.
22 812
4 2442
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
1A diode [1N4002+]
When using an external relay, use a 1N4002 diode or larger.
Important: When flashing your module for Security Only, the Ground When Armed (GWA)
function is pre-configured. When flashing your module for Remote Start & Security, you must
manually assign the designated output to Anti Grind (AG) Starter Kill.
(Applicable to CORE 194+.)

9933.CHRYSLER 7.34.195.3 2010 Chrysler Sebring Convertible
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2010 Chrysler Sebring Convertible. Refer to “Pre-installation and application warnings” for a list of important notes.
Data harness, 8-pin white connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H1/1 Tan (Data) HS CAN 1 Low Sentry Key Module on ignition switch, black 8 pin plug, pin 7 data white (CAN B BUS) Mandatory
H1/2 Tan/Black (Data) HS CAN 1 High Sentry Key Module on ignition switch, black 8 pin plug, pin 6 data white/orange (CAN B BUS) Mandatory
H1/3 Orange/Brown (Data) HS CAN 2 Low OBD-data link connector, black 16 pin plug, pin 14 data white/dk. blue (Diagnostic
CAN C)
Mandatory
H1/4 Orange/Green (Data) HS CAN 2 High OBD-data link connector, black 16 pin plug, pin 6 data white/lt. blue (Diagnostic
CAN C)
Mandatory
H1/5 Lt. Green No Connection No Connection
H1/6 Violet/Brown (MUX) Ignition Output Sentry Key Module on ignition switch, black 8 pin plug, pin 1 MUX violet/brown Remote Start
Only
H1/7 Orange/Black No Connection No Connection
H1/8 Yellow/Black (-) RAP Off Output under driver dash, lt. gray 43 pin plug, pin 14 - violet Remote Start
Only
Analog input/output harness, 22-pin white connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/1 Lt. Green/Black (-) Factory Alarm Arm Output No Connection
H2/2 Blue/White (-) Ground When Running (Status) Output No Connection
H2/3 Dk. Green/Black (-) Lock Output No Connection
H2/4 Red/White (-) Ground When Armed (GWA) Output [3] Starter:
driver fender, black 20 pin plug, pin 12 (I-4); black 14 pin plug, pin 6
(V6)
Ignition:
Sentry Key Module on ignition switch, black 8 pin plug, pin 3
Must use a relay.
Must use a 1N4002 diode or larger.
+
+
yellow/violet (for starter kill
only)
pink
Security Only
H2/5 Brown/Black (-) Horn Output horn switch, white 6 pin plug, pin 3 - dk. green/violet Optional
H2/6 Brown/White (-) AUX 1 Output No Connection
H2/7 White (+) (+) AUX 1 Output No Connection
H2/8 Violet/Black (+) AUX 2 Output No Connection
H2/9 Dk. Blue/Black (-) Unlock Output No Connection
H2/10 Lt. Blue/Black (-) Factory Alarm Disarm Output No Connection
H2/11 Brown/Red (+) Siren Output [2] Security Only
H2/12 Pink (+) Ignition Sense Input No Connection
H2/13 Violet (+) Door Input No Connection
H2/14 Brown (+) Brake Input No Connection
H2/15 White/Blue (-) Activation Input No Connection

10 933.CHRYSLER 7.34.195.3 2010 Chrysler Sebring Convertible
©2022 VOXX•DEI LLC. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/16 Red/Blue (-) Headlight Detection Input No Connection
H2/17 Black/White (-) E-Brake Input No Connection
H2/18 Orange/Black (+) Instant Alarm Input No Connection
H2/19 Blue (-) Trunk Input No Connection
H2/20 Green (-) Door Input No Connection
H2/21 Gray (-) Hood Input [1]
H2/22 Violet/White (AC) Tach Input No Connection
Main harness, 12-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H3/1 Blue/White Relay 1 N.C. - No Connection No Connection
H3/2 Blue/Red Relay 1 N.O. - (+) 12 Volt Input above driver kick, green 43 pin plug, pin 4 + red (40A) Remote Start
Only
H3/3 Blue Relay 1 COM - (+) Ignition Output Sentry Key Module on ignition switch, black 8 pin plug, pin 3 + pink Remote Start
Only
H3/4 White/Brown Relay 3 N.C. - No Connection No Connection
H3/5 White Relay 3 COM - (+) Parking Light Output driver kick, harness to rear
When using optional t-harness a relay is required for parking lights.
+ white/violet Mandatory
H3/6 Red (+) 12 Volt Input above driver kick, green 43 pin plug, pin 4 + red (40A) Mandatory
H3/7 Lt. Green/Red Relay 2 N.O. - No Connection No Connection
H3/8 Lt. Green Relay 2 COM - No Connection No Connection
H3/9 Lt. Green/White Relay 2 N.C. - No Connection No Connection
H3/10 Black (-) Ground Sentry Key Module on ignition switch, black 8 pin plug, pin 4 - Black Mandatory
H3/11 White Relay 3 COM - (+) Parking Light Output driver kick, harness to rear
When using optional t-harness a relay is required for parking lights.
+ white/violet Mandatory
H3/12 Red (+) 12 Volt Input above driver kick, green 43 pin plug, pin 4 + red (40A) Mandatory
Relay harness, 10-pin white connector (H4)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H4/1 N/A No Connection No Connection
H4/2 Red/Black (+) 12 Volt Input No Connection
H4/3 Pink/Black Flex Relay (pin 87A) No Connection
H4/4 Pink/White (+) Flex Relay Output No Connection
H4/5 Red (+) 12 Volt Input No Connection
H4/6 Green Starter Input (conn. side) No Connection
H4/7 Violet (+) Starter Output (vehicle side) No Connection
H4/8 Orange (+) Accessory Output No Connection
H4/9 Red/White (+) 12 Volt Input No Connection