Directed Xpresskit DBALL2 User manual

Installation Guide
Update Alert: Firmware updates are posted the web on a regular basis. We recommendon
that you check for firmware and/or install guide updates prior to installing this product.
Vehicle Application Guide ....... .................. ..................................... ............................... ......................................................
Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )
Type 1.............. ..... .................................................................................................................... ..........................................
Type .............. ..... ..........................................2 .......................................................................... ..........................................
Type .............. ..... ..........................................3 .......................................................................... ..........................................
Type 4.................................................................................................................................................................................
Type 5.............. ..... .................................................................................................................... ..........................................
Type 6................................................................................................................................................................................
Programming
Module Programming ...................... .............................................................................. .......... ...........................................
Module Reset.. ...................................................................................................................................................................
Hard ... ....Reset.. ................................................................................................................................................................
Feature & Option List..........................................................................................................................................................
Feature Programming.........................................................................................................................................................
LED Diagnostics & Troubleshooting...................................................................................................................................
Limited One-Year Consumer ........Warranty.......................................................................................................................
Quick Reference Guide......................................................................................................................................................
02
03
05
07
09
11
13
15
16
16
17
17
18
20
21
Index
®Hyundai and Kia their respective companiesare registered trademarks and property of .
The HYUNDAI1 firmware for 2 is an all-in-one door lock and override module compatible withDBALL
specific Hyundai and Kia vehicles.
This module can only be flashed and configured using Xpress at www.directechs.com orVIP
using the Directechs Mobile application for smartphones. Refer to the Module Programming
section 15on page for more information.
Takeover feature is on the Kia Optima. The engine will stop when a door is opened.not available
Rev.: 20170818
Platform: DBALL2
Firmware: HYUNDAI1
© 2017 Directed. All rights reserved.

Vehicle Application Guide Page 2
The following table lists the vehicles and features which are compatible with this product. The number assigned to each
year allows you to determine which installation type should be used for your vehicle.
Vehicles
2015
2014
2013
2012
2011
2010
2009
PK-Immobilizer Bypass-Data No Key Req'd
AV-Panic Mode Activation
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
DL-Trunk / Hatch Release
FOB-Control of aftermarket alarm with OEM remote
RS-RAP Shut Down (Retained ACC Power)
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Hood Pin
SS-Entry Monitoring Trunk/Hatch Pin
ST-Brake Status (foot brake)
ST-E-Brake Status
ST-Ignition Status
Hyundai
Genesis (Smart Key) 11111••••••••D•••••••D
Genesis Coupe (Smart Key) 66622 2 ••••••••D•••••••D
Sonata (Smart Key) 3333 ••••••••D•••••••D
Sonata Hybrid 3333 ••••••••D•••••••D
Kia 1514131211 10 09
Magentis (Smart Key) 4 ••••••••D•••••••D
Optima (Smart Key) 4 ••••••••D•••••••D
Sorento (Smart Key) 555 ••••••••D•••••••D
Legend: PK: Transponder & Immobilizer Override
D: Data-to-Data (D2D) only AV: Horn & Lights Controls
•: D2D and W2W CC: Comfort & Convenience Controls
DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w / FOB Remote
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
Rev.: 20170818
Platform: DBALL2
Firmware: HYUNDAI1
© 2017 Directed. All rights reserved.

Page 3
Installation Type 1
PDM
(Power Distribution Module)
[1] ( ) Tach InputAC
(-) Trunk Status Input
(-) Door Status Input
Remote
Starter
(-) (Status)GWR
(-) OutputLock
(-) OutputUnlock
(-) OutputAUX
(+) Starter Output
(-) OutputTrunk
( ) Parking ights+L
Output
(+) R. Park. Light:
pin 1White,
(+) L. Park. Light: pin 2Brown,
EF21 - Black connector
Passenger kick panel
(+) Ignition Input
(+) 12V Input
(-) Ground
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
4: (-) Panic InputWhite/Violet:
9: (+) Ignition InputPink:
8 Starter: (+) InputViolet:
10: (-) (Status) InputBlue/White: GWR
[1] ( ) Tach Output: 5AC Violet/White:
(-) Keysense Output: Yellow/Black: 10
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
HS CAN High: , pin 6Orange
HS CAN Low:
Green, pin 14
HS CAN High: 3Tan/Black:
FT CAN High: 5Orange/Green:
HS CAN Low: 4Tan:
FT CAN Low: 6Orange/Brown:
18
169
FT CAN High: , pin 11Brown
(-) Keysense: , pin 12Orange
(+) Ignition Status: pin 9Yellow/Black,
FT CAN Low: , pin 10White
(+) 12V:
,White
pin 1
Located at the center
consol on driver sidee
21
20
17 18 191615
14
13
3456789
10 11 12
21
I/P Junction Box
(Driver Side Dash - )Rear View
1
Brake
pedal
2
4
1
3
(+) Brake: , pin 1Gray
Not required in D2D mode.
1A Diode Output ison Starter ONLY
required in W2W mode.
123
4678
13
9
17 20
12 16 19
11 15 18
10 14
5
(+) 12 : 13V Input Red:
(+) 12V
(-) Ground: 14Black:
(-) Ground
Diagnostic onnectorC OBDII
(connector side view)
These vehicles do support virtual tach.NOT A tach
source (from the vehicle or module) must be usedinterface .
() :+ Brake Status Output 6Gr :ay
(+) Brake Status Input
Refer to
www.directechs.com
for alternative
brake connections.
6 Amp Diodes
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
With the exception of the Diag connector, all adapters are displayed from the wire side (unless specified otherwise).OB IID nostic
10
DBALL2
RF
Prog utton. B
LED
4
14 12 2
TX
(-) Ground
RX
(+)12V
XKD2D65
1A Diode
(+)12V Input 7: Brown:
(+) PTS Output 8: Yellow:
1A Diodes
PTS Connector
(black conn. at
Start/Stop Switch)
(+) PTS 2: , pin 7White
(+) PTS 1: , pin 1Orange/Black
5
610 987
1432
Rev.: 20170818
Platform: DBALL2
Firmware: HYUNDAI1
© 2017 Directed. All rights reserved.

Rev.: 20170818
Platform: DBALL2
Firmware: HYUNDAI1
© 2017 Directed. All rights reserved.
Page 4
Type 1 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Hyundai Genesis (Smart Key) 2009-2013
HS CAN High Orange 6 Data OBDll. Black 16
HS CAN Low Green 14 Data OBDll. Black 16
FT CAN High Brown 11 Data Power distribution module in center console on driver side. White 20
FT CAN Low White 10 Data Power distribution module in center console on driver side. White 20
Keysense Orange 12 (-) Power distribution module in center console on driver side. White 20
Ignition Yellow/Black 9 (+) Power distribution module in center console on driver side. White 20
Brake Gray 1 (+) Brake switch. White 4
Parking Lights (Left) Brown 2 (+) Passenger kick. Black 21
Parking Lights (Right) White 1 (+) Passenger kick. Black 21
12 Volts White 1 (+) Drivers dash fuse box. White 1
PTS 1 Orange/Black 1 (+) Start/stop switch. Black 10
PTS 2 White 7 (+) Start/stop switch. Black 10
Wire Information Connector Information

Rev.: 20170818
Platform: DBALL2
Firmware: HYUNDAI1
© 2017 Directed. All rights reserved.
Brake
pedal
153 7
26489
10 14
12
16
11 1513 17 18
8
7
6
5
4
3
2
1
2019181716
131211109 15
14
765
4
321
18
1716
11
1413121110
9
8
15
654
321
16
14 15
131211109
78
Not required in D2D mode.
87
86 85
30
87A
[2] (-) Clutch:
, pin 1Green
21
Clutch Pedal
(-) KeySense : pin 12Red,
[1] ( ) Tach InputAC
(-) Trunk Status Input
(-) Door Status Input
Remote
Starter
(-) Parking Lights Output
(+) 12V Input
(-) rake StatusE-B Input
(+) 12V
(-) Ground
(-) Ground
(-) Hood Status Input
[1] ( ) Tach Output: 5AC Violet/White:
(-) Keysense Output: Yellow/Black: 10
[2]( ) Clutch Relay Output+:7Gray/Black:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
High: pin 6HS CAN Red,
HS CAN Low:
Blue, pin 14
(+) 12 : 13V Input Red:
(-) Ground: 14Black:
HS CAN High: 3Tan/Black:
FT CAN High: 5Orange/Green:
HS CAN Low: 4Tan:
FT CAN Low: 6Orange/Brown:
18
169
(-) Parking Lights: pin 8Brown/Black,
(+) Ignition
Status: Blue,
pin 15
(+) 12V:
Red,
pin 14
(-) E-Brake Status:
Brown/Orange 4, pin
FT CAN Low:
pin 10Blue,
FT CAN High:
pin 11Red,
(-) Hood Status: pin 31Yellow,
111
15 25
29 39
212
16 26
30 40
31314
48610597
18 2220 2419 2321
32 3634 3833 3735
17 27 28
31 41 42
Driver Side
Kick Panel
Blue Connector
I/ - Driver Side Fuse BoxP
(see back of I/P)
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
4: (-) Panic InputWhite/Violet:
9: (+) Ignition InputPink:
8 Starter: (+) InputViolet:
10: (-) (Status) InputBlue/White: GWR
(-) (Status)GWR
(-) OutputLock
(-) OutputUnlock
(-) OutputAUX
(+) Starter Output
(-) OutputTrunk
(+) Ignition Input
( ) E-B wire is- rake
inconnected only
vehicles equipped
with manuala
transmission.
(+) Starter wire is
connected to the
Brake Pedal connector
for vehicles equipped
with an automatic
transmission .only
AB
CC
D
D
G
A
1A Diode ison Starter wire ONLY
required in W2W mode.
1234
These vehicles do support virtual tach.NOT A tach
source (from the vehicle or module) must be usedinterface .
Diagnostic onnectorC OBDII
(connector side view)
Ground
() :+ Brake Status Output 6Gr :ay
(+) Brake Status Input
1234 678
13
9
17 20
12 16 19
11 15 18
10 14
5
PDM
(Power Distribution Module)
Located at the center
consol on driver sidee
(+) Brake:
pin 1Green,
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Installation Type 2
With the exception of the Diag connector, all adapters are displayed from the wire side (unless specified otherwise).OB IID nostic
[2] ( ) wire is connected to connector s equipped a+ Clutch Relay Clutch Pedal for vehicle with manual transmission .only
10
DBALL2
RF
LED
4
14 12 2
XKD2D65
TX
(-) Ground
RX
(+)12V
Prog utton. B
G
(+)12V Input 7: Brown:
(+) PTS Output 8: Yellow:
1A Diode
1A Diodes
PTS Connector
()black conn. at Start/Stop Switch
(+) PTS 2:
Pink, pin 7
(+) PTS 1:
Blue, pin 1
5
610 987
1432
Page 5

Rev.: 20170818
Platform: DBALL2
Firmware: HYUNDAI1
© 2017 Directed. All rights reserved.
Type 2 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Hyundai Genesis Coupe (Smart Key) 2010-2012
HS CAN High Red 6 Data OBDll. Black 16
HS CAN Low Blue 14 Data OBDll. Black 16
FT CAN High Red 11 Data Power distribution module in center console on driver side. White 20
FT CAN Low Blue 10 Data Power distribution module in center console on driver side. White 20
Keysense Red 12 (-) Power distribution module in center console on driver side. White 20
Ignition Blue 15 (+) Drivers dash fuse box. White 18
Brake Green 1 (+) Brake switch. White 4
Parking Lights Brown/Black 8 (-) Drivers dash fuse box. White 16
12 Volts Red 14 (+) Drivers dash fuse box. White 20
E-Brake Brown/Orange 4 (-) Drivers dash fuse box. Blue 14
Hood pin Yellow 31 (-) Drivers kick. Blue 42
Clutch Green 1 (-) Clutch pedal. White 2
PTS 1 Blue 1 (+) Start/stop switch. Black 10
PTS 2 Pink 7 (+) Start/stop switch. Black 10
Wire Information Connector Information
Page 6

Rev.: 20170818
Platform: DBALL2
Firmware: HYUNDAI1
© 2017 Directed. All rights reserved.
39
50 23
54 26
51 24
55 27
52 25
53 17
56 28
41 14
45 18
42 15
46 19
43 16
44 6
47 20
31 3
34 7
32 4
35 8
33 5
36 9
48
12
21
40
49
13
22
29
37
1
10
30
38
2
11
[1] ( ) Tach InputAC
(-) Trunk Status Input
(-) Door Status Input
Remote
Starter
( ) Park ghts- .Li Ouput
(-) Ground
(+) 12V Input
HS CAN High: , pin 6White
(-) Keysense:
Yellow or
Orange/Black,
pin 41
OR
(-) Keysense
Yellow
(Hybrid),
pin 47
FT CAN High:
White/Orange or
Blue (Hybrid), pin 12
FT CAN Low:
Yellow/Orange or
Orange (Hybrid), pin 11
HS CAN Low:
Yellow or
Brown (Hybrid),
pin 14
(+) 12V
(+) 12 13V Red:
(-) Ground (-) Ground: 14Black:
HS CAN High: 3Tan/Black:
FT CAN High: 5Orange/Green:
HS CAN Low: 4Tan:
FT CAN Low: 6Orange/Brown:
18
169
I/ - Driver SideP Junction Box Dash
()front view
White/Gray Connector
(Passenger Kick Panel or in
Driver Kick Panel for the Hybrid)
27
28 15 2
32 19 6
30 17 4
34 21 8
37 24 11
29 16 3
33 20 7
36 23 10
31 18 5
35 22 9
38 25 12
39
14
26
1
13
(+)12V: pin 13Red,
21
22 12 2
26 16 6
34 14 4
28 18 8
23 13 3
27 17 7
25 15 5
29 19 9
30
11
20
1
13
I/P Junction Box -
Driver Side Dash
(/P )see back of I Junction Box
(-) (Status)GWR
(-) OutputLock
(-) OutputUnlock
(-) OutputAUX
(+) Starter Output
(-) OutputTrunk
(+) Ignition Input
13
17
21
15
19
23
14
18
22
16
20
24
1
5
9
3
7
11
2
6
10
4
8
12
Brake
pedal
2
4
1
3
1A Diode on Starter
iswire ONLY
required in
W2W mode.
Not required in D2D mode.
These vehicles do support virtualNOT
A tach source (from the vehicletach.
or module) must be usedinterface .
(+) Ignition Status:
, pin 11Pink
(-) Parking Lights:
pin 22Pink,
BCM Above Gas Pedal-
1218 1319 1420 1521 1622 172324
123456
7891011
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
4: (-) Panic InputWhite/Violet:
9: (+) Ignition InputPink:
8 Starter: (+) InputViolet:
10: (-) (Status) InputBlue/White: GWR
Diagnostic onnectorC OBDII
(connector side view)
(+) Brake:
Green or
Green/Orange
(Hybrid),
pin 1
(+) Brake Status Input
Installation Type 3
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
With the exception of the Diag connector, all adapters are displayed from the wire side (unless specified otherwise).OB IID nostic
10
DBALL2
RF
LED
4
14 12 2
TX
(-) Ground
RX
(+)12V
XKD2D65
Prog utton. B
[1] ( ) Tach Output: 5AC Violet/White:
(-) Keysense Output: Yellow/Black: 10
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
() :+ Brake Status Output 6Gr :ay
(+)12V Input 7: Brown:
(+) PTS Output 8: Yellow:
1A Diodes
PTS Connector
(black conn. at
Start/Stop Switch)
(+) PTS 2:
Yellow/Orange,
pin 7
(+) PTS 1:
Yellow/Black,
pin 1
5
610 987
1432
1A Diode
Page 7

Rev.: 20170818
Platform: DBALL2
Firmware: HYUNDAI1
© 2017 Directed. All rights reserved.
Type 3 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Hyundai Sonata (Smart Key) 2011-2014
HS CAN High White 6 Data OBDll. Black 16
HS CAN Low Yellow 14 Data OBDll. Black 16
FT CAN High White/Orange 11 Data I/P junction box - driver side dash. White 24
FT CAN Low Yellow/Orange 10 Data I/P junction box - driver side dash. White 24
Ignition Pink 11 (+) I/P junction box - driver side dash. Black 30
12 Volts Red 13 (+) I/P junction box - driver side dash. Black 39
Keysense Yellow or Orange/Black 41 (-) Passenger kick. White 56
Brake Green 1 (+) Brake switch. White 4
Parking Lights Pink 22 (-) BCM above gas pedal. Gray 24
PTS 1 Yellow/Black 1 (+) Start/stop switch. Black 10
PTS 2 Yellow/Orange 7 (+) Start/stop switch. Black 10
Hyundai Sonata Hybrid 2011-2014
HS CAN High White 6 Data OBDll. Black 16
HS CAN Low Brown 14 Data OBDll. Black 16
FT CAN High Blue 11 Data I/P junction box - driver side dash. White 24
FT CAN Low Orange 10 Data I/P junction box - driver side dash. White 24
Ignition Pink 11 (+) I/P junction box - driver side dash. Black 30
12 Volts Red 13 (+) I/P junction box - driver side dash. Black 39
Keysense Yellow 47 (-) Drivers kick. White 20
Brake Green/Orange 1 (+) Brake switch. White 4
Parking Lights Pink 22 (-) BCM above gas pedal. Gray 24
PTS 1 Yellow/Black 1 (+) Start/stop switch. Black 10
PTS 2 Yellow/Orange 7 (+) Start/stop switch. Black 10
Wire Information Connector Information
Page 8

Rev.: 20170818
Platform: DBALL2
Firmware: HYUNDAI1
© 2017 Directed. All rights reserved.
Brake
pedal
(+) Brake: ,Brown
pin 1
[1] ( ) Tach InputAC
(-) Trunk Status Input
(-) Door Status Input
Remote
Starter
( ) Parking ights- L Output
(+) 12V
(-) Ground
(-) Ground
(-) Hood Status Input
[1] ( ) Tach Output: 5AC Violet/White:
(-) Output: 12Autolight Off Blue/Red:
(-) Output:Keysense 10Yellow/Black:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
(+) 12V Input
HS CAN High:
White, pin 6
HS CAN Low:
pin 14Black,
(+) 12 : 13V Red:
(-) Ground: 14Black:
HS CAN High: 3Tan/Black:
FT CAN High: 5Orange/Green:
HS CAN Low: 4Tan:
FT CAN Low: 6Orange/Brown:
18
169
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
4: (-) Panic InputWhite/Violet:
9: (+) Ignition InputPink:
8 Starter: (+) InputViolet:
10: (-) (Status) InputBlue/White: GWR
(-) (Status)GWR
(-) OutputLock
(-) OutputUnlock
(-) OutputAUX
(+) Starter Output
(-) OutputTrunk
(+) Ignition Input
FT CAN High:
White, pin 5
FT CAN Low:
Black, pin 15
7
1715
910 11 12
12 34 5
13
68
16 1814
C
(-) Driver Door Trigger:
Blue/Black,
pin 20
(+) Ignition Status: ,Yellow/Black pin 2
11
24
10
23
9
22
8
21
7
201812 13 14 15
12345
16
6
1917
A
(+) 12V:
Red, pin 1
I/P Box
(Above Driver
Kick Panel)
Connector G
4321
G
(-) Keysense:
9Orange, pin
Key Port - Under
Center Arm Rest
(-) Hood Status:
Yellow/Black,
pin 13 (-) Parking Lights
,Yellow/Black
pin 4
79
18 201610 11 12 13
12345
14
68
17 1915
B
1A Diode is required inon Starter wire ONLY
W2W mode.
2
4
1
3
BCM
(Above Brake Pedal)
A
B
C
1
687910
5
Not required in D2D mode.
These vehicles do support virtualNOT
A tach source (from the vehicletach.
or module) must be usedinterface .
Diagnostic onnectorC OBDII
(connector side view)
() :+ Brake Status Output 6Gr :ay
(+) Brake Status Input
324
(+)12V Input 7: Brown:
(+) PTS Output 8: Yellow:
Installation Type 4
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
With the exception of the Diag connector, all adapters are displayed from the wire side (unless specified otherwise).OB IID nostic
10
2DBALL
RF
LED
4
14 12 2
TX
(-) Ground
RX
(+)12V
XKD2D65
Prog utton. B
1A Diode
1A Diodes
(+) PTS 2:
Whit/Orange,
pin 7
(+) PTS 1:
Orange/Black,
pin 1 5
610 987
1432
PTS Connector
(black conn. at
Start/Stop Switch)
Page 9

Rev.: 20170818
Platform: DBALL2
Firmware: HYUNDAI1
© 2017 Directed. All rights reserved.
Type 4 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Kia Magentis (Smart Key) 2010
HS CAN High White 6 Data OBDll. Black 16
HS CAN Low Black 14 Data OBDll. Black 16
FT CAN High White 5 Data BCM above Brake pedal. Gray 18
FT CAN Low Black 15 Data BCM above Brake pedal. Gray 18
Ignition Yellow/Black 2 (+) BCM above Brake pedal. White 24
Driver Door Trigger Blue/Black 20 (-) BCM above Brake pedal. White 24
Parking Lights Yellow/Black 4 (-) BCM above Brake pedal. White 20
Hood Pin Yellow/Black 13 (-) BCM above Brake pedal. White 20
12 Volts Red 1 (+) I/P Junction box above driver kick. White 4
Keysense Orange 9 (-) Key port in center console. White 10
Brake Brown 1 (+) Brake switch. White 4
PTS 1 Orange/Black 1 (+) Start/stop switch. Black 10
PTS 2 White/Orange 7 (+) Start/stop switch. Black 10
Kia Optima (Smart Key) 2010
HS CAN High White 6 Data OBDll. Black 16
HS CAN Low Black 14 Data OBDll. Black 16
FT CAN High White 5 Data BCM above Brake pedal. Gray 18
FT CAN Low Black 15 Data BCM above Brake pedal. Gray 18
Ignition Yellow/Black 2 (+) BCM above Brake pedal. White 24
Driver Door Trigger Blue/Black 20 (-) BMC above Brake pedal. White 24
Parking Lights Yellow/Black 4 (-) BCM above Brake pedal. White 20
Hood Pin Yellow/Black 13 (-) BCM above Brake pedal. White 20
12 Volts Red 1 (+) I/P Junction box above driver kick. White 4
Keysense Orange 9 (-) Key Port - IN Center Console White 10
Brake Brown 1 (+) Brake switch. White 4
PTS 1 Orange/Black 1 (+) Start/stop switch. Black 10
PTS 2 White/Orange 7 (+) Start/stop switch. Black 10
Wire Information Connector Information
Page 10