Rimage Catalyst 6000 User manual

Rimage Catalyst™User Guide
6000 and 6000N

For more information visit www.rimage.com/support
2003484_A
Rimage Corporation reserves the right to make improvements to the equipment and software described in this document at any time
without any prior notice. Rimage Corporation reserves the right to revise this publication and to make changes from time to time in the
content hereof without obligation of Rimage Corporation to notify any person or organization of such revisions or changes.
This document may contain links to web sites that were current at the time of publication, but may have moved or become inactive
since. This document may contain links to sites on the Internet that are owned and operated by third parties. Rimage Corporation is not
responsible for the content of any such third-party site.
© 2016, Rimage Corporation
Rimage®and Everest® are registered trademarks of the Rimage Corporation. Rimage Catalyst™ and Prism™ are trademarks of the
Rimage Corporation. Windows®is a registered trademark of Microsoft Corporation.
All other trademarks and registered trademarks are the property of their respective owners.
The most recent version of this document can be found at www.rimage.com/support.
Rimage Corporation
7725 Washington Avenue South
Minneapolis, Minnesota 55439 USA
Toll Free +1.800.445.8288
Fax: [phone]
Service:
US: +1.800.553.8312, Option 2
International: +1.952.946.0004, Option 2
Rimage Europe GmbH
Albert-Einstein-Strasse 26
63128 Dietzenbach, GERMANY
Tel [phone]
Rimage Japan Co., Ltd.
2F., WIND Bldg.
7-4-8 Roppongi Minato-ku
Tokyo 106-0032 JAPAN
Tel [phone]
Rimage Taiwan
10F., No. 252, Sec.1,
Neihu Rd. Neihu Dist.,
Taipei City, 11493, TAIWAN
Tel [phone]
Rimage Information Technology
(Shanghai) Co., Ltd.
10B & 10C, World Plaza,
855 South Pudong Road
Shanghai, 200120 CHINA
Tel [phone]

Contents
2003484_A For more information visit www.rimage.com/support
Introduction .......................................................................................1
About this User Guide.................................................................................................... 1
About the Catalyst System........................................................................................... 1
Unpacking and Setup Instructions ............................................................................. 1
Important Information .................................................................... 2
Support Contact Information.......................................................................................2
Learn More Online......................................................................................................... 2
Technical Support ..........................................................................................................2
Optical Disc Recording Software Disclaimer.......................................................... 3
Safety and Compliance Information......................................................................... 3
Safety Precauons.............................................................................................................. 3
Identify the Parts of the Catalyst System ................................... 5
Front View ........................................................................................................................5
Identify the Parts of the Catalyst System ................................... 6
Back View with Everest Printer................................................................................... 6
Identify the Parts of the Catalyst System ................................... 7
Back View with Prism Printer ...................................................................................... 7
Identify the Parts of the Catalyst System ................................... 8
Parts Information ............................................................................................................ 8
DiscWatch™ Status Light .................................................................................................... 8
Display Panel ...................................................................................................................... 8
System Buon .................................................................................................................... 8
Disc Dispenser .................................................................................................................... 8
Beeper ................................................................................................................................ 8
Operate the Catalyst System........................................................ 9
Power On the Catalyst System ..................................................................................9
Power Off the Catalyst System .................................................................................. 9
Pause the Catalyst System ......................................................................................... 9
Operate the Catalyst System...................................................... 10
Load the Discs............................................................................................................... 10
Unload the Discs .......................................................................................................... 10
Set Your Printing Preferences ................................................................................... 10
Maintain the Catalyst System...................................................... 11
Overview...........................................................................................................................11
Cautionary Information.................................................................................................11
Preventative Maintenance Schedule........................................................................11
Diagnostic Tests..............................................................................................................11
Operate Gemini Utilities............................................................... 12
Start Gemini Utilities.....................................................................................................12
Change the Autoloader Display Name...................................................................12
Enable the Beeper........................................................................................................12

1
2003484_A For more information visit www.rimage.com/support
Introduction
This manual provides the information needed to congure, operate,
and maintain the Rimage Catalyst™ 6000 and 6000N. The terms
‘system’ and ‘autoloader’ may be used throughout this manual to refer
to the Catalyst products. The term printer refers to either the Everest
600 or Prism III printer.
For information specic to the Catalyst systems refer to the Rimage
Catalyst User Guide found at www.rimage.com/support.
Important! Your Catalyst system may not look exactly like the model
featured in this user guide.
About this User Guide
• While we try to maintain all versions of our manuals and
documentations, please note that the English version found on our
web site always contains the most up-to-date information.
• Unless otherwise indicated, all Windows navigation statements
are Windows 7 paths. Other Windows operating system navigation
may differ slightly.
• These notes and symbols are used throughout the manual to help
clarify information:
Note: A Note provides supplemental information or information
that may apply only in special cases. For example, memory
limitations, equipment congurations, or details that apply to
specic versions of a program would be included in a Note.
Tip: A Tip suggests alternative methods that may not be obvious
and helps you understand the benets and capabilities of the
product.
Important!
• An Important note provides information essential to the
completion of a task.
• Important supplemental information.
• You can disregard information in a Tip and still complete a
task, but do not disregard an Important note.
ȸCaution: A Caution indicates that failure to observe this guideline
could result in loss or damage to the equipment, product, software,
or data.
ȸWarning! A Warning indicates that failure to follow this guideline
could result in bodily injury to personnel operating or maintaining
the equipment.
About the Catalyst System
The Rimage Catalyst™ system is available with either the Everest® 600
printer or the Prism III™ printer. For information about your printer, refer
to the setup and installation guide or user guide that shipped with
your printer.
The Catalyst 6000N has an embedded computer (PC). The embedded
PC is a network-ready computer which enables operation via other
networked computers. The Catalyst 6000N can also be used without
a network by directly attaching a monitor, keyboard, and mouse.
The Catalyst 6000 requires an external computer to be used. The
Catalyst 6000 autoloader is not shipped with an external PC; You
must provide a PC. Refer to the Catalyst specications for minimum
and optimum PC requirements for the 6000. Technical Specications
for this product can be found at www.rimage.com/support.
Unpacking and Setup Instructions
To unpack your Catalyst system, refer to the unpacking label on
the autoloader box. For setup instructions, refer to the Setup and
Installation Guide that shipped with your product.

2
2003484_A For more information visit www.rimage.com/support
Important Information
This section provides support contact information, and cautions and
warnings, for the Catalyst system.
Technical Specications for this product can be found at www.rimage.
com/support.
Support Contact Information
US, Canada, Latin America
Rimage Corporation
7725 Washington Avenue South
Minneapolis, MN 55439
USA
Attn: Rimage Services
Email: [email protected]
Telephone:
North America: 800-553-8312
Mexico/Latin America: 952-946-0004 option 2
Fax: [phone]
Europe
Rimage Europe GmbH
Albert-Einstein-Str. 26
63128 Dietzenbach
Germany
Email: [email protected]
Telephone: [phone]
Fax: [phone]
Asia/Pacic
Rimage Japan Co., Ltd.
2F., WIND Bldg.
7-4-8 Roppongi Minato-ku,
Tokyo 106-0032 JAPAN
Email: [email protected].jp
Telephone: [phone]
Fax: [phone]
Rimage China
10B & 10C, World Plaza,
855 South Pudong Road
Shanghai, 200120 CHINA
Email: [email protected]
[email protected]
Telephone: [phone]
Contact Rimage Services
Website: www.rimage.com/support
When you contact Rimage
Services, please provide:
• System serial number and
software version
• Functional and technical
description of the problem
• Exact error message received
Copy and record the following information
from your Rimage product for future
reference.
Note: Make sure you update the Serial
Number anytime you receive a
replacement system.
Serial Number:
Product Name:
Date of Purchase:
Learn More Online
At www.rimage.com/support, you can experience Rimage’s world-
class Support and Services. From this online site you can access:
• Informaon about the latest soware and rmware updates
• Product specicaons
• The latest documents
• Current rmware and driver downloads
Technical Support
Rimage offers a variety of service and support options for the
Catalyst system including Next Business Day On-site Agreements,
Exchange Services, and Software Subscription and Support. Please
contact your Rimage Value Added Reseller or Rimage for additional
information and pricing.

3
Important Information
2003484_A For more information visit www.rimage.com/support
Optical Disc Recording Software
Disclaimer
This Product, Software, or Documentation may be designed to assist
you in reproducing material in which you own the copyright or have
obtained permission to copy from the copyright owner. Unless you
own the copyright or have permission to copy from the copyright
owner, you may be violating copyright law and be subject to payment
of damages and other remedies. If you are uncertain about your
rights, you should contact your legal advisor. If you are neither in
possession of the copyright nor have authorization from the owner of
the copyright, unauthorized copying of copyrighted material on an
optical disc or any other media violates national and international
legislation and can result in severe penalties.
Safety and Compliance Information
This manual and the indications on the product allow proper and safe
operation. The indication marks below help protect you and other
persons from injury, and equipment from damage.
Safety Precautions
To ensure safety, read these precautions and familiarize yourself with
their meaning before using the equipment.
ȸWarnings!
• The laser beam used by the CD/DVD Recorder is a Class 1 laser. Do not
attempt to open the recorder. An authorized technician should perform all
service procedures.
• Use of controls or adjustments or performance of procedures other than
those specied herein may result in hazardous radiant exposure.
• Never use any optical instrument in conjunction with this unit. To do so will
greatly increase the hazard to your eyes.
ȸCautions:
• For continued protection against risk of re, replace the fuse only with the
same type and rating. An authorized technician should perform all service
procedures.
• Use only the supplied AC power cord, or use a safety agency approved
power cord. For applications outside North America, refer to the nearest
Rimage ofce for assistance in selecting a locally approved power cord.
• This product is designed for an ofce environment.
• The Catalyst 6000N contains a lithium battery. There is a risk of explosion
if the battery is replaced by an incorrect battery. Dispose of the old battery
according to the manufacturer’s instructions included with the battery
packaging.

4
Important Information
2003484_A For more information visit www.rimage.com/support
Product Catalyst Product Model
Catalyst 6000N RAS32E
Catalyst 6000 RAS32
Notice for USA NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when this equipment is operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his own expense.
This product complies with UL 60950-1+A1+A2.
Notice for Canada This Class A digital apparatus complies with Canadian ICES-003 Issue 5:2012. Cet appareil numerigue de la classe
A est conforme a la norme NMB-003 du Canade.
This product complies with CAN/CSA-C22.2 No. 60950-1-07+A1+A2.
Notice for Europe This product is in conformity with the EMC Directive (89/336/EEC) and the Low-Voltage Directive (73/23/EEC) through
compliance with the following European standards: EN 55032: 2012 Class A Limit; EN 55024: 2010; EN61000-3-
2:2014; EN61000-3-3:2013; EN60950-1:2006+A1:2010+A11:2009+A12:2011+A2:2013. The CE mark has been afxed in
accordance with the CE Marking Directive 93/68/EEC.
Notice for Japan This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information
Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio interference may occur, in
which case, the user may be required to take corrective action.
Translation:
Notice for Australia This product complies with AS/NZS CISPR32:2013.
Notice for Taiwan This is class A digital device. It may cause radio-frequency interference when used in a residential area. In this case,
the users are advised to take appropriate precautions.
Translation:
這是甲類的資訊產品,在居住的環境中使用時,可能會造成射頻干擾,在這種情況下,使用者會被要求採取某些適當的對策.

5
2003484_A For more information visit www.rimage.com/support
Identify the Parts of the Catalyst System
Front View
Disc Dispenser
Display Panel
USB 3.0
(Catalyst
6000N Only)
Status Light
System Button
External Output Bin
Carousel
Embedded PC
Power Button
Lift Arm
Recorders
Front
Door

6
2003484_A For more information visit www.rimage.com/support
Identify the Parts of the Catalyst System
Back View with Everest®Printer
Catalyst 6000N
Power Cord Power Cord
Network Cable
Power Switch Power Switch
Catalyst 6000
Video
Connectors
USB Ports
USB Port

7
2003484_A For more information visit www.rimage.com/support
Identify the Parts of the Catalyst System
Back View with Prism™Printer
Catalyst 6000N
Power Cord Power Cord
Network Cable
Power Switch Power Switch
Catalyst 6000
Video
Connectors
USB Ports
USB Port

2003484_A For more information visit www.rimage.com/support 8
Identify the Parts of the Catalyst System
Parts Information
DiscWatch™Status Light
The Catalyst system is equipped with a status light that indicates
various conditions. The table below illustrates status light states and
explains the conditions indicated by each state.
Light State System Condition
Green
light on
The system is operating properly. No jobs are
currently processing.
Green
light
blinking
The system is operating properly. Jobs are
currently processing.
Yellow
light on
The system is waiting for the software to start.
Yellow
light
blinking
The front door may be open. Close the front
door to allow jobs to process.
Red light
on
The carousel may be out of blank discs. Fill
the supply bins with the appropriate media
type.
A system error requires operator intervention.
Check the client workstation or control center
for a message.
An equipment error occurred at initial start up,
such as missing print ribbon. Check the client
workstation or control center for a message.
Display Panel
The display Panel has a two-line display that informs you of operations or
conditions that require operator intervention, including the consumable status.
The two-line display includes:
Door Closed:
• Line 1: Ribbon and Bin Numbers
• Line 2: Ribbon Count and Bin Count
Door Open (Scrolling display):
• Line 1: Displays System Name / Disc Counter
• Line 2: IP Address / Discs Produced
After initialization, the Catalyst system displays the name of the embedded PC.
Refer to the Operate Gemini Utilities section on page 12 for more information.
Tip: The caret symbol ‘^’ in the upper right corner of the operator panel
indicates that the Rimage software is currently communicating with the
autoloader.
System Button
The system button is below the display panel. Press the system button to rotate
the carousel and position a bin so that discs can be loaded or unloaded. Each
time you press the system button, the carousel rotates to the next bin.
Tip: The carousel will rotate to a bin only after the software has completed
initializing the autoloader.
Disc Dispenser
The disc dispenser moves discs into the external output bin.
Beeper
The Catalyst system has a beeper that can be enabled to sound when user
intervention is required. Read the error message that displays on the display
panel or on your PC monitor and take appropriate action to correct the problem.
Refer to the Enable the Beeper section on page 12 for beeper setting options.

2003484_A For more information visit www.rimage.com/support 9
Operate the Catalyst System
This section provides you with the information needed to ready the
Catalyst system to produce discs.
Power On the Catalyst System
1. Press the power switch on the
rear of the autoloader.
• If you have a Catalyst 6000,
the system is powered on.
• If you have a Catalyst
6000N, continue with
step 2.
2. On the front of the autoloader,
press the PC power button to
power on the embedded PC. The
autoloader and embedded PC
power on.
Power Off the Catalyst System
• If you have a Catalyst 6000
• Close all open applications
• Press the main power switch on the rear of the autoloader to
power off the Catalyst system
• If you have a Catalyst 6000N
• Close all open applications
• Shutdown from Windows Start Menu
-or-
• Briey press and release the PC power button on the front of
the Catalyst system. This shuts down the software, Windows,
and the embedded PC.
ȸCaution: Do not press and hold the PC power button. If you
press and hold the PC power button, the embedded PC will not
shut down properly. This may cause data loss or corruption.
Note: It takes approximately 30 seconds for the system to
power off.
Pause the Catalyst System
1. Open the front door to pause operation.
2. Close the front door to resume operation.
Power Switch
PC Power Button

2003484_A For more information visit www.rimage.com/support 10
Operate the Catalyst System
Load the Discs
You can load up to 50 discs in each bin. You can use the procedure
below to place discs in a bin.
1. Open the front door.
2. Press the system button to rotate the carousel and place a bin in
position to load discs.
3. Place up to 50 discs to be recorded and/or printed in the bin.
• The default bin conguration for CD/DVD-based systems is:
Bin 1: CD-R
Bin 2: DVD-R
Bin 3: Output/Reject
External Output Bin: Unused
• The default bin conguration for systems with Blu-ray
recorders is:
Bin 1 = CD
Bin 2 = DVD
Bin 3 = BD
External Output Bin = Output/Reject
Important! Place the discs with the recording side facing down.
Tip: You may designate bins 1 through 3 as input, output, reject, or
output/reject and specify media type through your software.
4. Repeat steps 2 - 3 until the required bins are lled.
5. Close the front door.
Unload the Discs
1. Open the front door.
2. Press the system button to rotate the carousel and place a bin in
position to remove discs.
3. Remove all discs from the bin.
4. Repeat steps 2 - 3 until the required bins are empty.
5. Close the front door.
Set Your Printing Preferences
Printing preferences allow you to set up and run your Catalyst system
to produce the best possible label on your discs. Refer to your printer
user guide for specic printing preferences instructions.

11
2003484_A For more information visit www.rimage.com/support
Maintain the Catalyst System
Use the information in this section to keep your Catalyst system in
optimal operating condition.
Overview
Regular preventative maintenance of your Catalyst system can help
to ensure error-free recordings and clean printed labels. Maintenance
involves cleaning the system.
Note: The printer has its own maintenance requirements. Refer to your
printer user guide for maintenance information.
Cautionary Information
ȸCaution: To avoid damaging the Catalyst system during
maintenance:
• Never use oils, silicone, or other lubricants on any part of the
Catalyst system.
• Use only non-abrasive cleaners to wipe down the surfaces of
your Catalyst system.
• Never use cleaners to clean the embedded PC.
• Avoid pouring cleaners directly onto the Catalyst system.
Instead, apply the cleaner to the cloth rst.
• Observe precautions for electrostatic-sensitive devices
whenever you access the embedded PC.
Preventative Maintenance Schedule
Note: Your system may require more frequent maintenance if used in
a dusty area, such as a store or warehouse.
Before you begin:
ȸWarning! Always power off the autoloader and unplug the power
cord before you access the embedded PC.
1. Power off the Catalyst system.
2. Disconnect the power cord.
Important! Failure to follow the maintenance schedule outlined below
may void your warranty.
Task Tool Frequency
Wipe down the lift arm shaft. Pay
close attention to:
• The area around the base of the shaft
• The area just above the lift arm
Lint-free
cloth
Weekly
Wipe down all surfaces of the
autoloader including:
• Sides and top
• Door
• Output bin
• Carousel
• Base
• Top surface on the lift arm
Lint-free
cloth
Non-
abrasive,
all-purpose
cleaner
Weekly
Inspect air lter on the side of the
system and replace if necessary.
N/A Monthly
Inspect the openings at the back of
the autoloader. Remove dust and
debris if necessary.
Vacuum Monthly
Diagnostic Tests
Catalyst diagnostic tests are available to troubleshoot problems with
your system and ensure proper operation. For more information on
accessing, selecting, and performing diagnostic tests, refer to the
Catalyst Diagnostics document that is available at www.rimage.com/
support.

2003484_A For more information visit www.rimage.com/support 12
Operate Gemini Utilities
Operate Gemini Utilities
The Rimage Software Suite includes an application called Gemini
Utilities, which is used to change the display name of the Catalyst
system and to congure the beeper settings.
Tip: To access Gemini Utilities for the Catalyst 6000N, use the remote
desktop connection from a networked PC, or connect a monitor,
keyboard, and mouse to the Catalyst 6000N.
Note: Unless otherwise indicated, all Windows navigation statements
are Windows 7 paths. Other Windows operating system navigation
may differ slightly.
Start Gemini Utilities
1. Close all open software applications and stop all Rimage Services.
Note: Refer to your Rimage Software online help for additional
information.
2. From the Windows Start menu select: All Programs > Rimage >
Utilities > Gemini Utilities. Gemini Utilities opens.
Note: When the desired tasks are complete in Gemini Utilities,
remember to restart the Rimage Services.
Change the Autoloader Display Name
Use Gemini Utilities to enter the name displayed on the operator
panel.
1. Select the Override Name checkbox.
2. Clear the Use Computer Name checkbox.
3. In the Display Name eld, enter the new name.
4. Select Set Params to set the name.
5. Select Exit to close Gemini Utilities.
Enable the Beeper
You can change the number of beeps that occur when the system
requires user intervention, such as when out of media or in an error
state.
1. In the # of Beeps on Fault eld, select the number of beeps you
wish to hear when there is an error.
Tip: To disable the beeper, set the number to zero.
2. Select Set Params to set the number of beeps.
3. Select Exit to close Gemini Utilities.