Dish Network Hopper Manual

HOPPER DUO
SETUP
SETUP
INSTRUCTIONS

• If you are not seeing the screens listed in this guide, try changing your TV’s
input by pressing the “Source/Input” button on your TV.
• When you reach the activation stage of this guide, you will need either your
account number or your previous receiver’s ID number.
• Account number: Located along the upper-right corner of your DISH bill
or in the My Account Summary section of your mydish.com account.
• Receiver ID: Located on a label on the back of your previous receiver. It
begins with “R.”
• To find your closest UPS dropo location or to schedule a pickup at your cost,
call 1-800-742-5877 or visit ups.com/dropo.
Do you have questions?
Take a look at the back cover of this guide to contact DISH!
2

Disconnect Your Cables
Locate the power cable for the
Hopper Duo that you are replacing
and unplug it from the wall.
Locate the cable connected
to the “To Hub” port, and then
unscrew it from the receiver. Do
not unscrew it from the wall.
3

Locate the cable connected to the “Ethernet” port,
and then unplug it from the receiver. Do not unplug it
from the wall. (You may not have this cable.)
Disconnect Your Cables
HDMI 1
Determine the cable you are
using to receive audio/visual
signal. Then, unplug it from the
receiver but not from your TV.
L
R
AUDIO
VIDEO
OR
HDMI CABLE RCA CABLES
Ethernet
Ethernet
4

Connect the Home Video Network
cable to the “To Hub” port on your
replacement receiver.
Connect Your Cables
5

Ethernet
Ethernet
Connect the Ethernet cable to the
“Ethernet” port on your replacement
receiver. (You may not have this cable.)
Connect either the RCA cables
or the HDMI cable to the
corresponding port(s) on your
replacement receiver.
Connect Your Cables
OR
HDMI CABLE RCA CABLES
HDMI 1
L
R
AUDIO
VIDEO
6

03
Power Your Equipment
Plug the power cord from your
Hopper Duo into a power outlet,
and ensure that your TV is still
plugged in. Turn on your TV. It
could take up to 30 seconds for
you to see any images.
Make sure that the SmartCard is
secured firmly in the slot on the
side of your Hopper Duo.
7

Power Your Equipment
You will see a loading screen,
which could last for several
minutes.
When the Install Wizard screen
appears, go to step 4.
03
8

Pair Your Remote to Your Hopper
Press the SAT button on your
remote control to pair it to your
Hopper Duo. All of your previous
receiver’s recording timers and
other settings will be restored
automatically.
Once your remote is paired, the
Install Wizard will proceed to the
next step automatically.
9

Set Up Text to Speech
If you would like to have a digital
voice read the text onscreen, use
your remote control to highlight
the “Continue with Text to Speech”
button. Then, press SELECT.
If you do not want a digital voice to
read the text onscreen, use your
remote control to highlight the
“Next” button. Then, press SELECT.
10

Set Your TV Resolution
If the image onscreen looks clear
and correct, use your remote
control to highlight the “Keep”
button. Then, press SELECT.
If the image onscreen looks
incorrect, use your remote to
highlight the “Revert” button. Then,
press SELECT.
Depending on your TV, you may not see this screen.
If this screen does not appear, skip to step 7.
11

Acquire Satellite Signal
Wait while your Hopper Duo
acquires satellite signal. This could
take up to 10 minutes. Once signal
is acquired, the Install Wizard
will proceed to the next step
automatically.
If red “X’s” appear in the installation
summary, ensure that the “Home Video
Network” cable is firmly connected to
your Hopper Duo and the wall. Then,
use your remote control to highlight
“Retest Installation” and press SELECT.
12

Activate Your Hopper
(Internet Connection)
Use your remote to highlight the
“Zip Code” field and press SELECT.
Then use the number pad on your
remote control to enter your ZIP
Code.
Use your remote control to highlight
either the “DISH Account Number”
field or the “Previous Receiver
ID” field. Then, press SELECT and
use the number pad to enter the
selected number.
If your Hopper is not connected to the Internet, skip to step 8E.
13

Use your remote control to
highlight the “Activate” button, and
then press SELECT.
Once activated, you will see a
screen confirming that you activated
your Hopper Duo successfully. The
Install Wizard will then advance to
the next screen automatically. Go to
step 9.
Activate Your Hopper
(Internet Connection)
14

Activate Your Hopper
(No Internet Connection)
If your Hopper Duo is not
connected to the Internet, call
1-800-333-DISH (3474) to activate
it with a DISH agent. You will need
the Receiver ID and Smart Card ID
located on the Activation screen.
Once activated, you will see a
screen confirming that you activated
your Hopper Duo successfully. The
Install Wizard will then advance to
the next screen automatically.
15

Download Hopper Software
Your Hopper Duo will start
downloading software
automatically. This process will take
approximately 20 minutes.
Once your Hopper Duo completes
the software download, the Install
Wizard will advance to the next
screen automatically.
16

Review the Summary Screen
Review the Summary screen. Any fields
with green checkmarks are complete,
and yellow fields are steps that need your
attention. To change the information in a
yellow field, highlight the dropdown tile
and press SELECT. Then select an option
from the dropdown menu.
When you have completed all of
the steps on the Summary screen,
select the “Watch TV” tile to start
watching your favorite programming
with DISH.
17

Return Your Original Receiver
Package your old receiver in the box
that your new receiver came in. Using
the above photo as reference, place
the endcaps along each side of the
receiver, and then place the receiver
into the box.
Close the box by folding the
flaps toward the center. Seal the
box using clear packaging tape.
18

TORETURN EQUIPMENTTO DISH NETWORK
1. Remove Shipping Label Here
2. TurnLabel Over3.Peel and Apply Return Label to Box
R
E
T
U
R
N
S
L
I
F
T
H
E
R
E
SHIP
TO:
DISH NETWORK
[phone]
525 DUNNETT COURT
SPARTANBURG SC 29303
BILLING: P/P
CUE 9.5 SCL412 96.5A 10/2009
20126944
[phone]
13 MELO DR
NORTH BANGOR NY 12966
1 LBS1 OF 1
UPS 2ND DAY AIR
TRACKING #:
*** *** ** **** *** *
1Z
A1Z *8463124
*44*
NY 136 1-01
2
TORE TURN EQUIPMENT TO DISH NETWORK
1. Remove Shipping Label Here
2. TurnLabel Over3.Peel and Apply Return Label to Box
SHIP
TO:
DISH NETWORK
[phone]
525 DUNNETT COURT
SPARTANBURG SC 29303
BILLING: P/P
CUE 9.5 SCL412 96.5A 10/2009
20126944
[phone]
13 MELO DR
NORTH BANGOR NY 12966
1 LBS
UPS 2ND DAY AIR
TRACKING #:
*** *** ** **** *** *
1Z
A1Z *8463124
*44*
NY 136 1-01
2
R
E
T
U
R
N
S
L
I
F
T
H
E
R
E
PEELHERE AND
Locate the original shipping label on the side
of the box, turn the label over, and peel o
the yellow return shipping label to expose the
adhesive.
SHIP
TO:
SERVICE SPARTANBURGSERVICE CENTER
[phone]
525 DUNNET COURT
SPARTANBURG SC 29303
SERVICE SPARTANBURG SERVICE CENTER
[phone]
NULL
525 DUNNET COURT
SPARTANBURG SC 29303
1 LBS 1 OF 1
UPS 2ND DAY AIR
TRACKING #:
*** *** ** **** *** *
1Z
A1Z *8463124
*44*
SC 293 9-05
RS
2
DESC: RETURN
BILLING: P/P
RETURN SERVICE
REF1: XXXXXXXX
REF2: XXXXXX
DOC: XXXXXXX
ORD: XXXXXXXX
SN:RREJXXXXXXXXX
PN: XXXXXX
RA: XXXXXXXX
DEL: XXXXXXXX
REQTYPE:AE
QTY:1
UPS tracking
number
RA number
UPS DROPOFF LOCATION
Copy the RA and UPS tracking
numbers for your records, and
apply the yellow return label to
the top of the box.
Return the original receiver
at the nearest UPS dropo
location.
Return Your Original Receiver
19

We want to hear from you
so that we can keep delivering what
you need to enjoy your TV service.
Share your thoughts at mydish.com/tunedintoyou.
Get product support information at mydish.com/support.
Have questions?
Let us help!
Find helpful instructional videos at youtube.com/user/dish.
Chat with a human being by visiting us at mydish.com/chat.
- OR -
Call us at 1-800-333-DISH (3474).
DN010635