Divio NRP1482 User manual
Content
ii
C
ONTENTS
Chapter 1: Product Introduction
Overview ............................................................................................ 1
Key Features.................................................................................... 1
Hardware Specifications ....................................................................... 2
Knowing Your NRP1482 Series .............................................................. 3
Front Panel ...................................................................................... 3
NRP1482 Rear Panel ......................................................................... 4
Mechanical Dimensions......................................................................... 5
Mechanical Dimensions......................................................................... 6
Mechanical Dimensions......................................................................... 7
Chapter 2: Jumpers and Connectors
Before You Begin ................................................................................. 8
Precautions ......................................................................................... 8
Jumper Settings................................................................................... 9
Locations of the Jumpers and Connectors ..............................................10
Jumpers.............................................................................................11
Clear CMOS.....................................................................................11
Connector Pin Definitions.....................................................................12
54V Power-in Connector (Outside).....................................................12
PoE LAN 8 Ports RJ45 Connector .......................................................12
GPIO Connector ..............................................................................13
System Fan.....................................................................................14
USB2.0 Connector ...........................................................................14
HDD/PWR LED Wire.........................................................................15
SATA Connector ..............................................................................15
SATA Connector........................................................................ 16
SATA Power Connector .............................................................. 16
Audio Connectors...................................................................... 17
Power SW Connector................................................................. 17
COM Port Connector .................................................................. 18
Debug Port Connector ............................................................... 18
LAN1 Connector and USB 3.0 Ports ............................................. 19
LAN2 Connector and USB 3.0 Ports ............................................. 19
SPI BIOS Update Connector ....................................................... 20
HDMI Connector ....................................................................... 20
DVI-I and RS485 Connector ....................................................... 21
POE 8 Ports LAN LED Connector ................................................. 22
M.2 B Key Connector ................................................................. 23
PoE Switch Action Guidance .......................................................... 24
PoE Switch Connecter Define (Rear IO) ....................................... 24
PoE Switch LED Indicator Status (Front Side)................................ 24
PoE Switch Deployment ............................................................. 24
Block Diagram.............................................................................. 26
Chapter 3: System Setup
Removing the Chassis Cover.......................................................... 27
Installing the 3.5” HDD ................................................................. 28
Installing the 2.5” SSD/HDD .......................................................... 34
Tightening Cable Guidance For 2.5” SSD/HDD ................................. 37
Installing M.2 SSD ........................................................................ 39
Installing Memory SO-DIMM (Use DDR4 SO-DIMM).......................... 41
Preface
iii
Chapter 4: BIOS Setup
About BIOS Setup.........................................................................43
When to Configure the BIOS ..........................................................43
Default Configuration ....................................................................44
Entering Setup .............................................................................44
Legends.......................................................................................44
BIOS Setup Utility .........................................................................46
Main ....................................................................................46
Advanced .................................................................................47
Chipset.....................................................................................56
Security....................................................................................61
Secure Boot ..............................................................................62
Boot.........................................................................................62
Chapter 1: Product Introduction
1
CHAPTER 1: PRODUCT INTRODUCTION
Overview
Key Features
▪Intel Celeron J6412, Quad Core 2.0GHz
▪Max. 32GB DDR4 supported
▪
Dual display of HDMI and DVI-I
▪1 x 3.5” SATA HDD
▪
1 x 2.5” SATA HDD or SSD/1 x M.2 2242 Key B SATA III
(select either one)
▪
1 x 10/100/1000 Intel
®
Ethernet
▪
1 x 2.5G Intel Ethernet
▪
8 x 10/100 PoE (120W max PSE)
▪Support TPM 2.0 onboard
▪Support eMMC onboard (option)
Chapter 1: Product Introduction
2
Hardware
Specifications
CPU Support
▪
Intel 8
th
Gen Intel
®
Celeron
®
J6412, Quad Core, 2.0GHz base frequency,
2.6 GHz burst frequency (compatible with other Intel 8
th
Gen Intel Atom
®
(Elkhart Lake) processor X Series and Intel
®
Celeron
®
J Series)
Main Memory
▪Dual channel DDR4 3200 MHz SDRAM, max. 32GB
I/O Interface-Front
▪2 x USB 2.0 ports
▪
Power & HDD status LED
▪
PoE 8 ports status LED
I/O Interface-Rear
▪
2 x RJ45 (1 x 1GbE + 1 x 2.5GbE)
▪4 x USB 3.1 Gen1 ports
▪
1 x HDMI 2.0b (supports max. resolution 4096 x 2160 @ 60Hz)
▪
1 x DVI-I
▪
1 x UART port (RS-232/485 setting from BIOS)
▪1 x Min-in & 1 x Line-Out & 1 x MIC
▪
Power on/off switch
▪
54V DC-IN jack (4-pin)
▪
8 x Ethernet PoE port
-
802.3af/at compliance with total 120W max (PSE)
-
802.3af support 8 ports @ 15W
-
802.3at support 4 ports @30W
▪1 x 4DI/2DO (relay type) terminal block or 4DI/4DO GPIO DB15 port
(option)
Storage
▪1 x 3.5” SATA HDD
▪
1 x 2.5” SATA HDD or SSD/1 x M.2 2242 Key B SATAIII (select either one)
▪1 x eMMC 32GB (option)
Power Input
▪Adapter 54V/3.34A 180W
Dimensions
▪
360mm (W) x 49mm (H) x 224.5mm (D)
Environment
▪
Operating Temperature:
Ambient with air flow: 0°C to 40°C
▪
Storage temperature: -20°C to 70°C
▪
Relative humidity: 10% to 90% (non-condensing)
Certifications
▪
CE approval
▪FCC Class A
▪UL 62368 compliance
Chapter 1: Product Introduction
3
Knowing Your NRP1482 Series
Front Panel
LED Indicators
Indicates the power status of the system.
Indicates the status of the hard drive.
Dual USB Ports
Used to connect USB 2.0 devices.
PoE LAN LED Indicators
Indicates the status of the LAN ports.
2x USB 2.0 Ports
LED Indicators PoE LAN LED Indicators
Chapter 1: Product Introduction
4
NRP1482 Rear Panel
1x COM (RS232/RS485) Port (BIOS Support)
Supports RS232 and RS485 compatible serial devices.
DVI-I
Used to connect a digital LCD panel.
1.0 GbE RJ45
2.5 GbE RJ45
8x PoE LAN Ports RJ45 Connector
HDMI
Used to connect a high-definition display.
1.0 GbE RJ45/2.5 GbE RJ45
1x COM (RS232/RS485) Port
DVI-I
Audio Connectors
1x PWR SW
Used to connect the system to a local area network.
4x USB3.0 Ports
Four USB ports to connect the system with USB 3.0 devices.
Audio Connectors (Line in/Line out/MIC in)
Line in: Receives audio signal input
Line out: Provides audio signal output
HDMI 4x USB3.0 Ports
54V DC Input
MIC-in: Used to connect an external microphone
8x PoE LAN Ports RJ45 Connectors
Enables communication among network clients and delivers power using
the same RJ45 to PoE-enabled edge devices.
Power Switch
Press to power on the device.
54V DC Input
Used to plug a DC power cord.
Chapter 1: Product Introduction
5
224.50
Mechanical Dimensions
Rackmount Model
1
366.00
360.00
192.80
3.00
28.70
44.00
465.00
482.80
16.00
6.00
6.00
Chapter 1: Product Introduction
6
224.50
360.00
126.00
67.50
Mechanical Dimensions
Desktop Model
360.00
44.00
49.00
287.80
36.10
Chapter 1: Product Introduction
7
Mechanical Dimensions
Wallmount Model
360.00
0
60.00
160.00
8.20
60.00
50.50
68.50
373.80
387.80
44.
00
50.0
Chapter 2: Jumpers and Connectors
8
CHAPTER 2: JUMPERS AND CONNECTORS
This chapter describes how to set the jumpers and connectors on the
NRP1482 series motherboard.
Before You Begin
▪
Ensure you have a stable, clean working environment. Dust and dirt can
get into components and cause a malfunction. Use containers to keep
small components separated.
▪Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
–
A Philips screwdriver
–
A flat-tipped screwdriver
–
A set of jewelers screwdrivers
–
A grounding strap
–
An anti-static pad
▪Using your fingers can disconnect most of the connections. It is
recommended that you do not use needle-nosed pliers to disconnect
connections as these can damage the soft metal or plastic parts of the
connectors.
▪
Before working on internal components, make sure that the power is off.
Ground yourself before touching any internal components, by touching
a metal object. Static electricity can damage many of the electronic
components. Humid environments tend to have less static electricity than
dry environments. A grounding strap is warranted whenever danger of
static electricity exists.
Precautions
Computer components and electronic circuit boards can be damaged by
discharges of static electricity. Working on computers that are still connected
to a power supply can be extremely dangerous.
Follow the guidelines below to avoid damage to your computer or yourself:
▪Always disconnect the unit from the power outlet whenever you are
working inside the case.
▪
If possible, wear a grounded wrist strap when you are working inside the
computer case. Alternatively, discharge any static electricity by touching
the bare metal chassis of the unit case, or the bare metal body of any
other grounded appliance.
▪Hold electronic circuit boards by the edges only. Do not touch the
components on the board unless it is necessary to do so. Don’t flex or
stress the circuit board.
▪
Leave all components inside the static-proof packaging that they shipped
with until they are ready for installation.
▪
Use correct screws and do not over tighten screws.
Chapter 2: Jumpers and Connectors
9
Jumper Settings
A jumper is the simplest kind of electric switch. It consists of two metal
pins and a cap. When setting the jumpers, ensure that the jumper caps are
placed on the correct pins. When the jumper cap is placed on both pins, the
jumper is short. If you remove the jumper cap, or place the jumper cap on
just one pin, the jumper is open.
Refer to the illustrations below for examples of what the 2-pin and 3-pin
jumpers look like when they are short (on) and open (off).
Two-Pin Jumpers: Open (Left) and Short (Right)
Three-Pin Jumpers: Pins 1 and 2 are Short
Chapter 2: Jumpers and Connectors
10
Locations of the Jumpers and Connectors
The figure below shows the location of the jumpers and connectors.
CN7
C5B 24
17
4
3
2 3 1 4 5
1
C4
C2
C3
16
C1
9
4
1
4
F2 E2
D2 C2
B2
A2
2 1
22
25
C5A 8
33
1
H2
G2
30
14
18
14
18
32
35
19
20
27
28
19
1
20
27
28
29
25
H10
G10
F10 E10
D10 C10
B10
A10
32 31
30 29
32 31
30 29
CN5
4
FAN2
CN4 CN1
1
7
1
1
4 4
CN3 CN2
A
AA
BA
CA
CT
JP1
1
3
145 143
259
1
DIMM1
1
PWR_SW1
1
CN11
4
260
2
146 144
145 143
259
1
CN8
CN6
CN9
1 10
9
10
1 9
2 10
1
2
DIMM2
260
2
146 144
19
20
1
2
1
10
40
80
113
74
2
1
Chapter 2: Jumpers and Connectors
11
Jumpers
Clear CMOS
Connector type: 1x3 3-pin header
Connector location: JP1
1 3
Pin
Settings
1-2
Normal
2-3
Clear CMOS
1-2 On: default
Chapter 2: Jumpers and Connectors
12
Connector Pin Definitions
54V Power-in Connector (Outside)
Connector type: 2x2 4-pin header
Connector location: CON6
PoE LAN 8 Ports RJ45 Connector
Connector type: Phone Jack RJ45 2x4 Port PoE
Connector location: CON5
1 2
3 4
Pin
Definition
Pin
Definition
1
54V-in
2
54V-in
3
GND
4
GND
2
4
6
8
8
1
1
8
8 1
1 8
8
1
1
8
8
1
1
8
1
3
5
7
Chapter 2: Jumpers and Connectors
13
Pin
Definition
Pin
Definition
1
5.0V
2
GND
3
GPIO80
4
GPIO84
5
GPIO81
6
GPIO85
7
GPIO82
8
GPIO86
9
GPIO83
10
GPIO87
Pin
Definition
Pin
Definition
1
5.0V
2
GPIO84
3
GPIO85
4
GPIO86
5
GPIO87
6
GND
7
GPIO80
8
GPIO81
9
GPIO82
10
GPIO83
11
--
12
--
13
--
14
--
15
--
GPIO Connector
Connector type: 2x5 10-pin header
Connector location: CN8
10 9
15 11
10 6
5 1
2 1
Chapter 2: Jumpers and Connectors
14
Pin
Definition
Pin
Definition
1
GND
2
+12V
3
SYS2_FAN_TACO
4
SYS2_FAN_PWM
Pin
Definition
Pin
Definition
1
V5P0_USB2_HDR
2
V5P0_USB2_HDR
3
USB2_4_DN_CM
4
USB2_5_DN_CM
5
USB2_4_DP_CM
6
USB2_5_DP_CM
7
GND
8
GND
9
X
10
N/C
System Fan
Connector type: 1x4 4-pin header
Connector location: FAN2
USB2.0 Connector
Connector type: 2x5 10-pin header
Connector location: CN6
10 9
1
4
2 1
Chapter 2: Jumpers and Connectors
15
Pin
Definition
Pin
Definition
1
LED_PWR_PU
2
LED_PWR_LOGIC_N
3
LED_HDD_LOGIC_N
4
LED_HDD_PU
Pin
Definition
Pin
Definition
1
GND
2
SATA_CON1_TXP
3
SATA_CON1_TXN
4
GND
5
SATA_CON1_RXN
6
SATA_CON1_RXP
7
GND
HDD/PWR LED Wire
Connector type: 1x4 4-pin header
Connector location: CN11
SATA Connector
Connector type: 1x4 4-pin header
Connector location: CN1
4 1
7 1
Chapter 2: Jumpers and Connectors
16
Pin
Definition
Pin
Definition
1
GND
2
SATA_CON2_TXP
3
SATA_CON2_TXN
4
GND
5
SATA_CON2_RXN
6
SATA_CON2_RXP
7
GND
Pin
Definition
Pin
Definition
1
V12P0_SATA
2
GND
3
GND
4
V5P0_SATA
SATA Connector
Connector type: 1x4 4-pin header
Connector location: CN4
SATA Power Connector
Connector type: 1x4 4-pin header
Connector location: CN2, CN3
7 1 4 1
Chapter 2: Jumpers and Connectors
17
Audio Connectors
Connector location: AUDIO1
Power SW Connector
Connector type: 1x2 2-pin header
Connector location: PWR_SW1
Line-in
Line-out
1 2
Mic-in
Pin
Definition
Pin
Definition
1
GND
2
PWRBTN_N
Table of contents
