Dolphin DOLKWP300318 User manual

DOLKWP300318
Dual Frequency 300/318 MHz Keypad
v.2.22.17

S1 S1 Frequency Selection
GND
GND OP VIN
CON1
ON
S2
10
1 2 3 4
300Mhz 318Mhz
DIP
10
DIP
1
2
3
4
4 Sec
2 Sec
1 Sec
ON
S2 Function Config
3 State/9 PORT 2 State/10 PORT
OFF
STEP 1: Set Jumper S1
S1
S1
318 MHz
300 MHz
Figure 1
jumper
in place
Determine the operating frequency you
will use on your keypad installation. This
keypad can operate at either 300 MHz
or 318 MHz. At 300 MHz the keypad is
compatible with all 300 MHz receivers
with 10 dip switches. At 318 MHz the
keypad is compatible all 318 MHz
receivers with 9 dip switches.
(see Figure 1)
STEP 2: Set Jumper 4 on S2
• 300 MHz (10 dip switches) - Jumper set to OFF (in the DOWN position)
• 318 MHz (9 trinary dip switches) - Jumper set to ON (in the UP position)
STEP 3: Set the DIP switches to match the Receiver
Set the DIP switches of the keypad to “+” for ON or CLOSE, and “-” for OFF or
OPEN. Note: Do not use the center position.
ON
S2
1 2 3 4
ON
S2
1 2 3 4
318 MHz
(9 dip switch)
10
DIP
300 MHz
(10 dip switch)
not used

1. Press
2. Enter the “Master Code” (default is )
3. Press the button
4. Enter for change code
5. Enter for the number of user code (eg. “03” for the third user code, etc).
6. Enter the new “User Enter Code” (Must be 4 digits)
7. Press the button. The multi-color status LED flashes Green 3 times meaning
the code is accepted. If the multi-color status LED flashes 3 times Red, the
steps need to be repeated.
STEP 5: Programming the User Entry Code
1
1
*
*
432
0 1
1. Press
2. Enter the “Master Code” (default is )
3. Press the button
4. Enter for delete code
5. Enter for the number of user code (eg. “03” for the third user code, etc).
6. Press the button. The multi-color status LED flashes Green 3 times meaning
the code is accepted. If the multi-color status LED flashes 3 times Red, the
steps need to be repeated.
STEP 6: Deleting the programmed User Entry Code
1
2
*
*
432
0 1
1. Press
2. Enter your programmed usercode.
STEP 7: Activating the Keypad
1. Press
2. Enter the “Master Code” (default is )
3. Press the button
4. Enter for change code
5. Enter for “Master Code”
6. Enter the new “Master Code” (Must be 4 digits)
7. Press the button. The multi-color status LED flashes Green 3 times meaning
the code is accepted. If the multi-color status LED flashes 3 times Red, the
steps need to be repeated.
STEP 4: Programming the Master Code
1
1
*
*
*
432
0 0
NOTE: 3 beeps indicates a wrong code.
5-6 beeps indicates low battery.

DIRECT HARD WIRE:
RF Transmit Time Setting on S2
RF transmit 0 seconds
NOTE: Remove 9V battery
Use 9-24 VDC (see following page)
RF transmit 1 seconds
RF transmit 2 seconds
RF transmit 3 seconds
RF transmit 4 seconds
RF transmit 5 seconds
RF transmit 6 seconds
RF transmit 7 seconds
1
2
3
4
4 Sec
2 Sec
1 Sec
ON
S2 Function Config
3 State/9 PORT 2 State/10 PORT
OFF
ON
S2
1 2 3 4
S1 S1 Frequency Selection
GND
GND OP VIN
CON1
ON
S2
10
1 2 3 4
300Mhz 318Mhz
DIP
1
2
3
4
4 Sec
2 Sec
1 Sec
ON
S2 Function Config
3 State/9 PORT 2 State/10 PORT
OFF
GROUND
RELAY
POSITIVE
DOWN (300 MHz)
UP (318 MHz)
1. Disconnect the power by removing the battery.
2. Press the , , and keys simultaneously.
3. Re-connect the battery to power up the keypad.
4. Release the , , and keys.
Note: The keypad is returned to the default “Master Code” . And all User
Entry Codes are deleted.
1 432
1 4 7
1 4 7
Return to Default Settings
DOLKWP300318 OPERATION
ORANGE - Key depress
GREEN - Code was entered correctly and the keypad is transmitting
GREEN - Programming Mode
RED - (Flashing 3 times) Error was made in either programming mode or in
code entry.
Multi-color status LED

S1 S1 Frequency Selection
GND
GND OP VIN
CON1
ON
S2
10
1 2 3 4
300Mhz 318Mhz
DIP
1
2
3
4
4 Sec
2 Sec
1 Sec
ON
S2 Function Config
3 State/9 PORT 2 State/10 PORT
OFF
+12V
NC NO
CON1
CON2
KEYPAD
RELAY MODULE
9-24 VDC
POWER SUPPLY
*Relay and power supply NOT INCLUDED.
TO ADD RELAY OPTIONS:

The warranty period of Transmitter Solutions keypads is twenty-four (24) months.
This warranty shall begin on the date the keypad is manufactured. During the
warranty period, the product will be repaired or replaced (at the sole discretion of
Transmitter Solutions) if the product does not operate correctly due to a defective
component. This warranty does not extend to (a) the keypad case, which can be
damaged by conditions outside the control of Transmitter Solutions, or (b) battery
life of the keypad. This warranty is further limited by the following disclaimer of
warranty and liability:
EXCEPT AS SET FORTH ABOVE, TRANSMITTER SOLUTIONS MAKES NO
WARRANTIES REGARDING THE GOODS, EXPRESS OR IMPLIED, INCLUDING
WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE. BUYER MAKES NO RELIANCE ON ANY
REPRESENTATION OF TRANSMITTER SOLUTIONS, EXPRESS OR IMPLIED,
WITH REGARD TO THE GOODS AND ACCEPTS THEM “AS-IS/WHERE-IS”.
TRANSMITTER SOLUTIONS SELLS THE GOODS TO BUYER ON CONDITION
THAT TRANSMITTER SOLUTIONS WILL HAVE NO LIABILITY OF ANY KIND AS A
RESULT OF THE SALE. BUYER AGREES THAT TRANSMITTER SOLUTIONS
SHALL HAVE NO LIABILITY FOR DAMAGES OF ANY KIND, WHETHER DIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING INJURIES TO
PERSONS OR PROPERTY, TO BUYER, ITS EMPLOYEES OR AGENTS, AS A
RESULT OF THE SALE. BUYER ALSO AGREES TO HOLD TRANSMITTER
SOLUTIONS HARMLESS FROM ANY CLAIMS BUYER, OR ANY THIRD PARTY,
MAY HAVE AS A RESULT OF BUYER’S USE OR DISPOSAL OF THE GOODS.
BUYER HAS READ THIS DISCLAIMER AND AGREES WITH ITS TERMS IN
CONSIDERATION OF RECEIVING THE GOODS.
WARRANTY:

2480 South 3850 West, Suite B
Salt Lake City, UT 84120
[phone] • [phone] fax
www.transmittersolutions.com