Dolphin DOLGDO300310 User manual

Thank you for your purchase of the Transmitter Solutions Dolphin
wireless keypad. The DOLGDO300310 will accommodate one 4 digit PIN
to activate a signal transmission.
Package contains:
Keypad
9 volt battery
2 screws + wall anchors
Keypad instructions
Please follow the detailed instructions below in order to set up the Dolphin keypad to
operate with your garage door opener or receiver.
2. OPERATIONAL FEATURES
Keypad Instructions
Dolphin Wireless Garage Door Keypad
Dual Frequency 300/310 MHz
Product # DOLGDO300310
Pressing any key illuminates the keypad for 5 seconds.
A "buzzer" indicates each button depression.
After 20 incorrect key entries, the keypad will “lock up” for 40 seconds.
If the battery is low the single LED flashes rapidly for 5 seconds, indicating it is
time to replace the battery.
After you have entered a valid code, the keypad LED will flash during the 5 second
"time out" period. During the “time out” period you may press any key and the
keypad will send another signal to your receiver each time you press a key.
The key resets your entry. If you make a mistake while entering your PIN,
pressing the key resets your entry so you can start over.
HINT: If you always begin your PIN with the you will reduce the likelihood of
faulty operation

300
310
S2S1
300
310
S2S1
300
310
S2S1
310 MHz
310 MHz
- (8 dip switch)
300 MHz
- (10 dip switch)
- (10 dip switch)
Back of
Keypad
a. Remove the access door on the top back of the keypad by sliding the door
in the direction of the arrow. (see Figure 1)
b. Locate the frequency switches on the top of the electronic board located
inside of the access door. (see Figure 2)
3. SET FREQUENCY JUMPER
a. Determine the operating frequency you will use on your keypad installation.
This keypad can operate at either 300 MHz or 310 MHz. At 300 MHz the keypad is
compatible with the Hive 300/310 receiver and all 300 MHz receivers with 10 dip
switches. At 310 MHz the keypad is compatible with the Hive 300/310 receiver,
and all 310 MHz receivers with 8 dip switches and 310 MHz receivers with 10 dip
switches. (see S1 and S2 on Figure 3)
3
Figure 3
Figure 1
Figure 2
jumper
in place
access
door
300MHZ
310MHZ
S2
S2
S1
310MHz
8 dip
10 dip
dip
switch
selection
jumper
300MHz
4. SET DIP SWITCHES
a. Set the DIP switches of the keypad to match the DIP switch settings of the
receiver, or a functioning transmitter. (see Figure 4)
b. Enter then the 4 digit PIN on the keypad, and then press # to activate the
receiver. If you just purchased the keypad, the factory default 4-digit PIN is 1234.
So please enter 1-2-3-4 #. If the receiver does not operate, reverse the keypad
DIP switches, and re-enter 1-2-3-4 #.

c. To change the 4 digit PIN (example)
TIP: When you enter the correct code followed by #, the keypad LEDs flash slowly
for 5 seconds. If you enter an incorrect code, the keypad LED will glow steady for
5 seconds.
TIP: When you have entered the programming mode of # # the small LED glows
a steady red. When you complete the change of the PIN the small LED flashes
twice quickly.
To reset the keypad to the factory default code, remove the 9 volt battery and
depress and hold any key on the keypad, then reinstall the battery. Continue holding
the key down for 5 seconds and then release the key. The keypad is now reset to
the factory defaults.
Position the keypad on the garage door frame with the provided screws.
Lift up the cover and insert the long screw above the keypad in the slot
provided (a).
Remove the battery cover and insert the second long screw in the
lower slot (b).
Replace the battery cover.
# # 1-2-3-4 _-_-_-_ #
(Old Pin) followed within 5 seconds by (New PIN)
pin must be four digits
300MHZ 310MHZ
S2
S1
Back
Opening
4
5. RETURN TO DEFAULT SETTINGS
3
Figure 4
dip
switches
cover
1. Desconnect the power by removing the battery.
2. Press the , , and keys simultaneously.
3. Re-connect the battery to power up the keypad.
4. Release the , , and keys.
Note: The keypad is returned to the defaul “Master Code” . And all User
Entry Codes are deleted.
1 432
1 4 7
1 4 7
Return to Default Settings

Other Dolphin wireless garage door keypads by Transmitter Solutions:
DOLGDO433RC - 433 MHz 4 channel, long range, rolling code
DOLGDO315390 - 315/390 MHz, 9 dip switch
7
8
The keypad is approved by the FCC and it complies with Part 15 of the FCC Rules. Its
operation is subject to the following 2 conditions:
1. This device may not cause harmful interference.
2. The device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC ID: SU7DOLGDO300310
The warranty period of this product is 24 months, beginning from the manufacturing date.
During this period, if the product does not operate correctly, due to a defective component,
the product will be repaired or replaced at the sole discretion of Transmitter Solutions. This
warranty does not extend to the product casing which can be damaged by conditions
outside of the control of Transmitter Solutions.
DO NOT let children use the keypad without adult supervision. Children can injure
themselves, or others, if left unsupervised. Make sure all the required safety devices are
installed before operating any door.
If this transmitter triggers other doors in your neighborhood, change all your transmitters
and receivers to a new code setting.
6
5. RETURN TO DEFAULT SETTINGS (continued)
ORANGE - Key depress
GREEN - Code was entered correctly and the keypad is transmitting
GREEN - Programming Mode
RED - (Flashing 3 times) Error was made in either programming mode or in
code entry.
Multi-color status LED