Dometic Enerdrive EN220080-12 User manual

User Manual
EN220080-12 / EN230100-12
Rev. 1.0

Enerdrive Inverter-Charger Owners Manual (Rev. 1.0)Page 2
For safe and optimum performance, the Enerdrive Inverter must be used properly. Carefully read and follow all instructions and
guidelines in this manual and give special attention to the CAUTION and WARNING statements.
Please Keep This Manual For Future Reference
Disclaimer
While every precaution has been taken to ensure the accuracy of the contents of this guide, Enerdrive assumes no responsibility for
errors or omissions. Note as well that specications and product functionality may change without notice.
Important
Product Numbers
Please be sure to read and save the entire manual before using your Enerdrive Inverter-Charger. Misuse may result in damage to the
unit and/or cause harm or serious injury. Read manual in its entirety before using the unit and save manual for future reference.
Enerdrive Inverter-Charger Owners Manual (Rev. 1.0)
Service Contact Information
Dometic Power & Control (Enerdrive) Pty Ltd
P.O. Box 9159, Wynnum Plaza, Queensland, Australia 4178
Ph: 1300 851 535 / Fax: [phone]
Email: [email protected] | Web: www.enerdrive.com.au
EN220080-12
EN230100-12
12V-2000W-80A Inverter-Charger
12V-3000W-100A Inverter-Charger
Notice of Copyright
Enerdrive Inverter-Chargers owner’s manual © 2023 Dometic Power & Control (Enerdrive) Pty Ltd. All rights reserved. No part of this
document may be reproduced in any
form or disclosed to third parties without the express written permission of Enerdrive Pty Ltd,
P.O. Box 9159, Wynnum Plaza, Queensland,
Australia 4178.
Enerdrive reserves the right to revise this document and to periodically make changes to the content hereof without obligation or
organisation of such revisions or changes, unless required to do so by prior arrangement.
Exclusions For Documentation And Product Usage
Assumes no responsibility or liability for losses, damages, costs or expenses, whether special, direct, indirect, consequential or
incidental, which might arise out of the use of such information. The use of any such information will be entirely at the user’s risk.
Reminds you that if this manual is in any language other than English although steps have been taken to maintain the accuracy of the
translation, the accuracy cannot be guaranteed.
Shall in no event be liable to anyone for special, collateral, incidental, or consequential damages in connection with or arising out of
purchase or use of these Enerdrive products. The sole and exclusive liability to Enerdrive, regardless of the form of action, shall not
exceed the purchase price of the Enerdrive products described here in.
Unless specically agreed to in writing,
Dometic Power & Control (Enerdrive) Pty Ltd : makes no warranty as to the accuracy,
suciency or suitability of any technical or other information provided in its manuals or other documentation.
Makes no warranty, either expressed or implied, including but not limited to any implied warranties of merchantability or tness
for a particular purpose, regarding these Enerdrive products and makes such Enerdrive products available solely on an “as is” basis.

TABLE OF CONTENTS
Product Description
Introduction
Understanding the Unit
Installing the Unit
Unit Operation
Troubleshooting
Specications
Warranty
1 PRODUCT DESCRIPTION
The Enerdrive Sinewave Inverter-Charger includes the items listed below.
• Inverter-Charger base unit
• Multi-Function Display
• 25’ RJ12 Display Cable
• Owner’s manual
Page 3
Page 3
Page 4
Page 6
Page 10
Page 12
Page 29
Page 30
Page 31
Series
12V
230VAC
EN220080-12 2000W 12V-80A 16A IEC
16A
12V-100A
3000W
EN230100-12
Inverter Charger By-Pass
Model No. AC Output Types
Rating

2 INTRODUCTION
IMPORTANT SAFETY INFORMATION
Page 4
Thank you for purchasing the Enerdrive Sinewave Inverter-Charger. With our state of the art, easy to use design, this product will
oer you True Sinewave AC power for your RV, Marine, 4WD and remote power needs also recharging your battery automatically
when 240V AC is available. The Sinewave Inverter-Charger can run multiple 240V AC-powered appliances when you need AC
power Ogrid. The multi-stage battery charger oers charging proles for multiple dierent types of batteries. The built-in
transfer switch will automatically switch between 240V mains supply when available and battery power when 240V mains is
not available.This manual will explain how to use this unit safely and eectively. Please read and follow these instructions and
precautions carefully.
This section contains important safety information for the Enerdrive Inverter. Each time, before using the Enerdrive
Inverter-Charger, please READ ALL instructions and cautionary markings on or provided with the inverter, and all appropriate
sections of this guide. The Enerdrive Inverter-Charger contains no user serviceable parts. See Warranty section for how to handle
product issues.
Enerdrive Inverter-Charger Owners Manual (Rev. 1.0)
DANGER! Fire & or Chemical Burn Hazard
Do not cover or obstruct any air vent openings and/or install in a zero-clearance compartment.
DANGER! Failure to follow these instructions
can result in death or serious injury
• When working with electrical equipment or lead-acid batteries, have someone nearby in case of an emergency.
• Study and follow all the battery manufacturer’s specic precautions when installing, using and servicing the battery connected to
the inverter.
• Wear eye protection and gloves.
• Avoid touching your eyes while using this unit.
• Keep fresh water and soap on hand in the event battery acid comes in contact with eyes. If this occurs, cleanse right away with
soap and water for a minimum of 15 minutes and seek medical attention.
• Batteries produce explosive gases. DO NOT smoke or have an open spark or re near the system.
• Keep unit away from moist or damp areas.
• Avoid dropping any metal tool or object on the battery. Doing so could create a spark or short circuit which goes through the
battery or another electrical tool that may create an explosion.

WARNING! Explosion Hazard
LIMITATIONS OF USE
• Do not use in connection with life support systems or other medical equipment or devices.
CE EMC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules (for 120V models) and comply with the CE EMC Standard on 230V models. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Page 5
• DO NOT install the unit near ammable fumes or gases (such as propane tanks or large engines).
• AVOID covering the ventilation openings. Always operate unit in an open area.
• Prolonged exposure to high heat or freezing temperatures will decrease the working life of the unit.
• DO NOT connect AC power sources like utility power or generator to the AC outputs of the unit. It will damage the
unit and may cause re. Feeding AC to the AC output of the unit is not covered by warranty.
• The 12V DC unit is designed for use on 12V House Battery System only. Use on a higher house battery system will
damage the unit and lead to unit explosion.
• The 24V DC unit is designed for use on 24V House Battery System only. Use on a lower house battery system will
damage the unit and lead to battery explosion.
WARNING!
Shock Hazard, Keep Away From Children
• Avoid moisture. Never expose unit to snow, water, etc.
• Unit provides high voltage AC; treat the AC output socket the same as regular wall AC sockets at home.

3 UNDERSTANDING THE UNIT
WARNING!
CAUTION
Before beginning unit installation, please consider the following:
• The unit should be used or stored in an indoor area away from direct sunlight, heat, moisture or conductive contaminants.
• When placing the unit, allow a minimum of three inches of space around it for optimal ventilation.
UNDERSTANDING THE UNIT FEATURES
3000W 120V GFCI Series
Enerdrive Inverter-Charger Owners Manual (Rev. 1.0)Page 6
• It is recommended that all wiring be done by a certied technician or electrician to ensure adherence to the applicable electrical
safety wiring regulations and installation codes. Failure to follow these instructions can damage the unit and could also result in
personal injury or loss of life.
MAIN UNIT REAR
A
B
C
D
E
F
G
H
i
J
K
L
M
N
O
P
Item Description
AC Input IEC Power Button DC Negative Stud
DC Positive Stud
Chassis Ground Connector
CAN BUS Port
Display Port
Battery Temperature Sensor Port
Ignition Start Port
Program Port
AC Input Breaker
AC Output IEC
Output RCD
AC Output Indicator
Status Indicator
Power Indicator
Description DescriptionItem Item
QFans and Fan Guards
DescriptionItem
D
L
C
A
B
G
H I
M
N
O
J
E F
P
K
Q

Page 7
TYPICAL WIRING BLOCK DIAGRAM OF INVERTER-CHARGER
Battery Bank
AC Load
12V/240Ah
50W
100W
200W
500W
1000W
1500W
2000W
2500W
3000W
Estimated run time on 12V Battery Bank
on 12V Input Models
2 hrs
1 hr
49 mins
37 mins
27 mins
11 hrs
4 hrs
44 hrs
23 hrs
A
Fuse/Circuit
Breaker Rating 250Adc
12V 2000W System 12V 3000W System
300Adc
• The use of deep cycle battery is highly recommended for power inverter application
• For battery size, you need to identify how much and for how long the inverter has to provide AC power to the loads (based on Amps
x hour energy consumption). It is recommended to purchase as much battery capacity as possible.
DC Fuse or Circuit Breaker
B
• DC-rated fuse or DC-rated circuit breaker connected along the DC positive line is required.
• Based on the size of the Battery Bank, determine the overall short circuit current rating of the battery bank from the battery
manufacturer. The fuse or circuit breaker has to be able to withstand the short circuit current that can be supplied by the battery
bank.
• For battery banks with total capacity under 500Ah the most aordable ANL fuse type can be used. Otherwise use Class-T type.
REMOTE SCREEN
INVERTER/CHARGER

Page 8 Enerdrive Inverter-Charger Owners Manual (Rev. 1.0)
12V 2000W series
12V 3000W series
AWG # 2/0
The typically recommended wire length is limited to <1.5m or less for each of the positive and the negative. For longer wires, a
proportionally thicker gauge is required to compensate for additional voltage drop
AWG # 3/0 AWG # 4/0
AWG # 4/0 AWG # 4/0 AWG # 4/0
DC Disconnect Switch
C
• A DC Disconnect Switch connected along the DC positive line is recommended. The rating of the switch is with the same or higher
rating of the selected fuse or circuit breaker. Use ignition protected switches when required by local codes.
• This switch is used to disconnect the positive of the battery bank to the unit’s positive terminal during maintenance/repair
service,when not in use, or when troubleshooting.
DC Input Cable
D
• All DC Input Wires should be insulated multi-strand low resistance wires.
• The DC wires must be copper and with minimum 105°rating.
Chassis Ground
E
Model
1.5 metres (Recommended) 2 metres 3 metres
Thinnest DC Input Wires Gauge Used
12V 2000W series
12V 3000W series
These guidelines assume you are using the DC supplied cable and fuse sizes recommended in this manual. If you are using dierent
sizes, refer to the applicable installation code for the DC grounding detail.
In marine applications, the main AC-DC ground bonding may require galvanic isolators to avoid galvanic corrosion. Check your local
electrical codes.
AWG # 1/0
AWG # 3/0
AWG # 8
Model
Recreation Vehicle Marine
Thinnest DC Input Wires Gauge Used
CAUTION
These guidelines assume you are using the DC supplied cable and fuse sizes recommended in this manual. The use of a thinner
gauge in the DC wires may cause the inverter to trigger the under-voltage shut down under heavy load conditions. It may also melt
the wire insulation and catch re, resulting in death or serious injury. The choice of the wire gauge should also match or exceed the
ampacity rating of the DC fuse and holder being used.
DANGER!
The unit chassis has to be grounded properly before use. Never operate the unit without proper grounding. Failure to do so will
result in death or serious injury.

Page 9
AC Input Source
F
AC Hardwire Output
G
AC Output Socket and AC Output Thermal Breaker:
H
Display Port
J
BTS Port
L
Multi-Function Display
K
I
An AC source is usually grid power or an AC Generator. The acceptable AC Input voltage range and frequency are as shown:
An automatic or manual AC source selector switch can be used to switch between the multiple sources of shore power to the unit.
Usually, the AC Main Panel includes a main circuit breaker that serves as over-current protection and as a disconnect for the AC shore
power supply line. Additional AC circuit breakers serve individual circuits and one of the AC circuit breakers will serve the unit. During
By-Pass mode, the AC Input source will serve the AC Output Load and also the AC Input current for the charger when it is used to
charge the battery.
The unit is designed to accept non-Sinewave AC Input Source supplied by a generator.
An AC Sub-Panel is recommended to incorporate an AC output circuit breaker and breakers for individual load circuits. Use the same
wire size as used for the AC Input Wire.
The port is used to connect to the Multi-Function Display of the unit.
The display is used to provide unit information and for unit setting.
The port is used for connecting to the optional Battery Temperature Sensor. The thermistor installed inside the ring terminal is used to
measure the battery terminal temperature and the unit will make compensation on battery charging voltage for battery charging.
A single AC Output socket is provided for direct AC output from the unit. An overcurrent protective device (thermal breaker) is
connected in series with the AC Output Socket to avoid excessive current being drawn from it.
230VAC Series 180 - 260 VAC 47 - 53 Hz
Follow the electrical and/or building code when you choose AC Branch Breaker and AC Input wire Size. Connect the unit to any AC
Input Source.
Smaller size AC Input wire can be used when a lower amperage rated AC Input Circuit Breaker is used from upstream to feed the unit.
Model Acceptable AC Input Voltage Range Acceptable AC Input Frequency Range
230VAC Series 16A (maximum) #14 AWG (minimum)
Model Acceptable AC Input Voltage Range Acceptable AC Input Frequency Range
Model
Total AC Output AC Output Hardwire Total AC Output AC Output Hardwire
2000W/230VAC
3000W/230VAC
By-Pass Mode Current (Maximum) Inverter Mode Current (Maximum)
16A
* Limited by AC Output Thermal Breaker connected in series with the AC Output Socket.
** Limited by Inverter maximum AC Output Current during inverter mode.
16A
16A
16A 13A 13A
8.7A 8.7A

Page 10 Enerdrive Inverter-Charger Owners Manual (Rev. 1.0)
Choosing the location:
Mounting the Unit:
Ignition Start Port, Program Port, Can-BUS Port
M
The Ignition Start Port is used for connecting to the ignition start signal from vehicles to control the operation of the inverter.
The Program Port This USB port is for system rmware upgrade use only. This CANNOT be used for charging Smartphones or
USB powered devices. Mis-used of this port can potentially damage the unit and is not covered by the warranty. This port is
located on the side of the Multi-Function Display and an extra port that shares the same function is also located below the
Ignition Start Port on the 2000W models.
The CAN-BUS Port (not shown in the wiring block diagram)
This is for unit communication through the CAN interface. Mis-used on this port can potentially damage the unit and is not
covered by the warranty. This port is located at the back of the Multi-Function Display and an extra port that shares the same
function is also located near the Ignition Start Port on the 2000W models.
4 INSTALLING THE UNIT
WARNING! Explosion Hazard!
• DO NOT install the unit near ammable fumes or gases (such as propane tanks or large engines).
• AVOID covering the ventilation openings. Always operate unit in an open area.
The unit should only be installed in locations that meet the following requirements:
• Do not allow water or other uids to drip or splash on the unit.
• Environment temperature should be between -20 °C and 40 °C
• Allow at least 75mm of clearance around the unit. The more clearance for ventilation around the unit, the better the performance.
• Choose an appropriate mounting location.
• The unit can be mounted in any direction.
• Use the mounting template below to mark the positions of the mounting screws.
• Drill the 4 mounting holes and place the unit in position and fasten the unit to the mounting surface.
4-Ø3.5
145
120 120
All Dimensions in mm
4.0
6.0
98 75
75
31
24
Recommended
opening size for the
Multi-Function Display
(108 x 83 mm)
288
200 140.4
412.9
440.7
307
288 307
270
495.9
532.9
77.5

Page 11
DC Input Connection:
Chassis DC Ground Connection:
Multi-Function Display Connection:
The unit should only be installed in locations that meet the following requirements:
• Connect the grounding wire to the unit’s Chassis DC Ground Lug located near the DC Input terminal and the other side of the cable
to the common grounding point.
• For a Recreation Vehicle, the common ground point is usually the vehicle chassis or a dedicated DC ground bus / main shunt.
• For Marine, the common ground point is usually the DC ground bus or engine negative bus.
Note: Do not use the Chassis DC Ground Lug for your AC Grounding, For AC Grounding, see AC Wiring instructions for more details.
WARNING! Electrical Shock Hazard
The unit ‘On/O’ switch does not disconnect the DC power from the battery. Use the DC Disconnect Switch or disconnect the DC
input cables to disconnect the DC power from the battery before working on any circuits connected to the unit.
Failure to follow these instructions can result in death or serious injury.
CAUTION
Reversing the DC Input terminals will damage the unit. Damage caused by reverse polarity connection is not covered by the
warranty.
IMPORTANT
DC terminals tightening torque 12-13 Nm
• Connect a negative DC input cable between the unit DC negative terminal and battery negative terminal. (or the system side of
the shunt if installed)
• Make sure the Disconnect Switch is in the OFF position. Connect a positive DC input cable between the unit DC positive terminal
and one terminal of the Disconnect Switch.
• Connect another DC input cable between the other terminals of the Disconnect Switch to one side of the terminal of the fuse
holder or DC rated circuit breaker (OFF position).
• Connect another DC input cable between the other terminal of the fuse holder or DC rated circuit breaker to the battery positive
terminal.
Note: For Marine application, either the DC fuse or DC rated circuit breaker needs to be installed within 18cm from the battery
positive terminals.
• Install the selected fuse to the fuse holder.
• Route the RJ12 cable from the unit to your desired location for the Multi-Function Display and connect one end of the cable to the
main unit Display Port and the other end of the cable to the Display Panel socket located at the rear panel of the Multi-Function
Display.

Enerdrive Inverter-Charger Owners Manual (Rev. 1.0)Page 12
BTS (Battery Temperature Sensor) Connection (optional):
Ignition Start Port Connection (optional):
Quick Test on Unit after Installation:
To provide more accuracy and precision on battery voltage charging against battery temperature, a BTS (sold separately) can be used.
The BTS can also be used to terminate the charging cycle when it senses the temperature of the battery rise to above 60 °C or fall
below 0 °C. See ‘Understanding the Error Code’ E19-E21 for more details. Use the following procedure to install the BTS.
• Connect the RJ12 end of the BTS cable to the BTS Port on the main unit.
• Install the ring terminal end of the BTS cable to the negative terminal of the battery bank.
• Connect a small AC load like a 40W light bulb to the AC Output of the unit.
• Switch DC disconnect switch to ON to provide battery power to the unit, then press and hold On/O button on Main unit or ‘Power’
button on Display panel for 1 second to turn unit or Inverter ON
• The ‘Status’ LED on display will turn Amber indicating inverter is ON. AC Output indicator turns green indicating the AC is available
at the AC Output terminal of the unit.
• Verify the 40W light bulb is ON.
• Switch ON the Main Circuit Breaker on the AC Input Panel.
• Switch ON the AC Input Circuit Breaker that provides AC Input power to the unit.
• If AC input source is available, the ‘Status’ LED amber will ash for about 10 seconds indicating the AC Input source is available. It
will then turn to solid green or ashing green indicating the unit is running from the AC input source.
• Verify the 40W light bulb remains ON.
• The unit is successfully installed and functioning properly.
The ignition start connection provides an inverter ON/OFF function through the Ignition Start Port. See more details on Understanding
of Ignition Start On/O function.
Understanding the Indicator/Push Button/Unit Functions
1.
4. 5. 6. 7. 8.
2.
3.
9.
RemoteCANBUS
GND H L VCC

 
FRONT BACK
10.
The unit is preset with factory default settings and will fulll the basic needs for inverter-charger operation. The display is used to
provide information about the unit status and the unit function can be customized through the Display.
Once the unit function is customized, the display can be removed if desired, as the unit can run without it.
5UNIT OPERATION

Page 13
• The and the button can be used to scroll through each unit setting. If a particular setting needs to be modied, press and
hold the ‘Menu/Set’ button for 5 seconds and the set parameter will ash on the display. Use the or button to scroll
through the available settings. Once the desired setting is chosen, press and hold the ‘Menu/Set’ button until a beeping sound
occur and the new setting is saved.
• Press ‘Escape’ button once to return back to Normal Operation. (If none of the button is triggered for about 5 seconds, display will
also return back to Normal Operation.
• To turn the inverter ON: press and hold until hearing the beep (in about 1 sec.). Display turns on and shows ‘-- -- --‘, all icons turn
ON, followed by the revision levels of the main unit ‘Rx.x’ and then the Display revision levels ‘rx.x’ (where x = any number).
• To turn the inverter OFF: press and hold until hearing the beep (in about 1 sec.). Display turns o and the unit cannot be turned on
again but after about 3 sec (when hearing the deactivation of the internal relays).
Note: When AC Input is available, this ‘Power’ button cannot be used to turn OFF the unit.
• Press once to view unit setting on display. See more details on Viewing and Change Unit Setting section.
When unit is in normal operation mode, Press ‘Menu/Set’ button once to view unit setting as listed on the Unit Setting Function Chart.
• Press and hold for 5 seconds to turn OFF or ON the AC Output Switch (use this button as an AC Output ON/OFF function for the
Output Socket).
• The and the button can be used to scroll through DC Current ‘A’, AC Output Power ‘KW’ and Battery Voltage ‘V’.
1.
2.
3.
4.
5.
Power Indicator
AC Output Indicator
Status Indicator
Power Button
Menu/Set Button
DescriptionItem
6.
7.
8.
9.
10.
Up Button
Down Button
Escape Button
Display Panel Socket
Program Port
DescriptionItem
Power ON
ON
OFF
GREEN
Green (Flash)
Amber
Red
Amber
(Flash)
Status
AC Output
Unit is power ON
AC Output Switch is turned ON and AC is available at the Output Socket
AC Output Switch is turned OFF and AC is not available at the Output Socket
AC Output is running from Utility
AC Output is running from utility and battery charger is charging the battery
Utility is detected and is under verication. AC Output is still running from
Inverter and will switch to Utility in about 10 seconds
AC Output is running from Inverter
Error/Warning occurs. Display will show Error orWarning code
Indicator Status Function
Normal Operation
When unit is On, the Multi-Function display shows Battery Voltage ‘V’.
Pressing any button will illuminate the backlighting of the display for about 10 seconds.
‘Power’ button (Same function as the green ‘On/O’ push button on the main unit):
‘Menu/Set’ button:
‘Escape’ button:
Viewing and Change Unit Setting
and button:

Enerdrive Inverter-Charger Owners Manual (Rev. 1.0)Page 14
Unit Setting Function Chart
Inverter
ON : Use as Inverter only. No By-Pass functions.
ON : (Default): Buzzer is enabled. Unit buzzes whenWarning or Error occurs.
OFF : Buzzer is disabled. Unit does not buzz whenWarning and Error occur.
ON : (Default): AC Charger is enabled. Charge battery when AC Input is available.
Li : (Default): Lithium Battery, default Bulk Charge/FloatVoltage is 14.4V/13.5V*
12V/3000W Models: Selectable Ranges 25A, 40A, 60A, 80A, 100A (Default 100A).
12V/3000W Models: Selectable Range: 20A, 15A, 10A, 5A, 2A (Default 10A).
12V/2000W Models: Selectable Ranges 10A, 20A, 40A, 60A, 80A (Default 80A).
12V/2000W Models: Selectable Range: 15A, 10A, 8A, 4A, 2A (Default 8A).
24V/3000W Models: Selectable Ranges 10A, 20A, 30A, 40A, 50A (Default 50A).
24V/3000W Models: Selectable Range: 8A, 6A, 5A, 3A, 2A (Default 5A).
24V/2000W Models: Selectable Ranges 5A, 10A, 20A, 30A, 40A (Default 40A).
24V/2000W Models: Selectable Range: 6A, 5A, 4A, 3A, 2A (Default 4A).
AGM : AGM Battery, default Bulk Charge/Float Voltage is 14.3V/13.4V*
FLd : Flooded Battery, default Bulk Charge/FloatVoltage is 14.4V/13.5V*
HI : High <35°C
(Default): Normal 15 -
35°C : Low < 15°C
Bulk/Absorption voltage is based on the battery type chosen. All battery types have selectable ranges
of 13.8 – 14.8V*. (Default on Li Battery is 14.4V*)
Float voltage is based on the battery type chosen. All battery types have selectable
ranges of 13.0 – 14.0V*. (Default on Li Battery is 13.5V*)
230 Vac Models: Range: 3, 5, 7, 10, 15
(Default 15A).
Select to reset all settings to default
Battery Recharge Voltage Selectable Range: 12.8 to 14.0V (0.1V step)* (Default on
GEL, AGM, Flooded, PGM battery setting is 12.8V* and Li setting is 13.3V).
PGM : Program, default Bulk Charge/FloatVoltage is 13.8V/13.2V*
PSY : : Power Supply Mode, Default Power Supply Voltage 13.8V*
OFF : AC Charger is disabled. No battery charging when AC Input is available.
Battery Low Disconnect Voltage selectable ranges is 10.5 - 12.0V (0.1V steps)
*(Default voltage is set to 12.0V*)
Battery LowWarning Voltage selectable ranges is 11.0 - 12.5V (0.1V step)*
(Default voltage is set to 12.5V*)
Battery Low RecoveryVoltage selectable ranges is 11.5 - 13.0V (0.1V step)
*(Default voltage is set to 13.0V*)
OFF : (Default): Continuous AC Output when inverter is ON
10 : Continuous AC Output when inverter is ON and AC load is > 10W
15 : Continuous AC Output when inverter is ON and AC load is > 15W
20 : Continuous AC Output when inverter is ON and AC load is > 20W
25 : Continuous AC Output when inverter is ON and AC load is > 25W
Inverter can be turned ON & OFF with a press of the power button. (AC OUT)
Charger &Transfer Auto Connect when Mains is Connected (Within Range)
Whole Unit can be turned OFF by HOLDING the Power Button for 5-seconds
F01
ATO
Load Sense
Battery Low Disconnect
Battery LowWarning
Battery Low Recovery
Audible Buzzer
AC Charger
Battery Type
Bulk Current
Bulk/Absorption/Voltage
Absorption to Float Current
FloatVoltage
RechargeVoltage
Battery Temperature
AC Input
Source Circuit Breaker
Factory Default
F02
F03
12.0*
F04
12.5*
F05
13.0*
F06
F07
F08
F09
100
F10
14.4*
F11
10
F15
15
F16
F12
13.5*
F13
13.3*
F14
Unit Setting Display Description and Available Setting
*for 24V models all of the voltage values are doubled.

Page 15
Solid: Unit is running in Battery Charger mode and is charging the battery.
Solid: AC Input is available and is in the operating range.
Battery bar(s) in solid indicating the unit is running in Battery Mode. The bars show estimated remaining
battery power.
Battery bar(s) with the last bar ashing indicates the unit is running in By-Pass mode and the battery
charging process is in progress. The charging stages are indicated by the number of bars.
4 bars in solid: indicates the battery is fully charged and it is in Float stage
Top bars ashing: indicates the battery is in Absorption charging stage
Bottom bar ashing: indicates the battery is in Bulk charging stage and the battery is > 11.5V
No bar: indicates the battery is in Bulk charging stage and the battery is > 10.5V
Battery icon ashing: indicates the battery is in Bulk charging stage and the battery is below
10.5V
Second top bar ashing: indicates the battery is in Bulk charging stage and the battery is > 13.5V
Second bottom bar ashing: indicates the battery is in Bulk charging stage and the battery is
> 12.5V
4 solid bars: Battery is Full
3 solid bars: Battery capacity with 75% remaining
2 solid bars: Battery capacity with 50% remaining
1 solid bar: Battery capacity with 25% remaining
No bar: Battery is empty. Inverter will shut down when it reaches under-voltage shutdown point.
Note: This indicator is for reference use only. It varies depending on battery health or type used.
Solid: Unit is running in By-Pass mode. (The transfer switch is switched to AC Input Source).
• AC Output power is running from AC Input Source.
• AC Output is available at both the AC Output socket and the AC Output Hardwire terminal if AC Output
switch is turned On (indicated by AC Output indicator located on the left side of the Display
and also the Main unit being On).
Note: Press and hold the ‘Escape’ button on the Display panel for 5 seconds to toggle AC Output switch On/O.
Solid: Unit is running in Battery Mode (The transfer switch is switched to Inverter)
• AC Output power is running from the inverter
• AC Output is available at both the AC Output socket and the AC Output Hardwire terminal if AC Output
switch is turned On (indicated by AC Output indicator located on the left side of the Display and also the
Main unit being On).
Note: Press and hold the ‘Escape’ button on the Display panel for 5 seconds to toggle AC Output switch On/O.
Understanding the Display Icons during Unit Operation
Icons Meaning
POWER
AC OUTPUT
STATUS
AC
AC
IN AC
OUT
AC OUT
AC
IN AC
OUT
AC
INPUT
Battery
Inverter
Mode
Charger
Mode
AC OUT
AC OUT

Enerdrive Inverter-Charger Owners Manual (Rev. 1.0)Page 16
‘A’ icon On indicates the display shows battery discharge current (28A as shown)
‘kW’ icon on, it indicates the display shows AC Output power in kW (0.80kW = 800W as shown)
‘V’ icon on, it indicates the display shows battery voltage in V (12.8V as shown)
Warning icon on, it indicates the display shows Error/Warning Code (E01 as shown, Battery Low
Disconnected error)
Equalization on Flooded battery is in process. This function is available for use with Flooded battery type
only. The display will also show the equalization voltage during the process. Follow the instruction
provided by the battery manufacturer when performing the equalization process.
Indicating the Main unit rmware revision (R:1.0 shown)
Indicating the Display Panel rmware revision (r:1.0 shown)
- Display shows battery voltage (14.2V), use
When there is a blackout (AC Input Source or Shore Power is not available), unit is running in Inverter/Battery Mode. Unit will
automatically switch to getting AC Power from the inverter. Charger is disabled.
Note: In By-Pass Mode, the ‘Power’ button function is disabled. It cannot be used to turn O the unit.
- ‘Power’ indicator on indicates unit is On.
- If ‘AC Output’ indicator is On, it indicates the AC Output Switch is turned On (AC is available at the
output socket and the output hardwire terminal).
- If ‘AC Output’ indicator is O, it indicates the AC Output Switch is turned O (AC is not available at the
output socket and the output hardwire terminal).
- Press and hold ‘Escape’ button for 5 seconds to toggle AC Output Switch On and O.
- If ‘Status’ indicator is solid green, it indicates battery is fully charged.
- If ‘Status’ indicator is ashing green, it indicates battery charging is in progress.
- is On indicates AC Input Source is in use.
- is On indicates AC Output is getting the power from AC Input source.
- is On indicates the charger is enabled and is charging the battery.
- icon indicates the charging stage of the battery
AC Input Power.
or button to see DC Current charging the battery,
AC
Display Character Meaning
INT ABU
CHG ON Automatic Backup with Battery Charger Function Enabled (Unit Default setting)
When AC Input Source or Shore Power is available, unit is running in By-Pass Mode. AC Output is getting the power from the
AC Input Source or Shore Power. Charger is enabled and Inverter is in standby condition.
Exploring the Unit Settings
a) Inverter and Charger Functions
(i) Automatic Backup with Battery Charger Function Enabled – Unit Default
Setting (‘INT’ = ‘ABU’, ‘CHG’ = ‘ON’)
This is the most commonly used setting on the unit. The charger function is enabled and the Inverter is in standby condition
when AC Input Source or Shore Power is available. The Inverter will automatically turn on when AC Input source or shore
power is interrupted. This provides smooth, uninterrupted AC power to the load.
AC
AC
INPUT
AC
IN AC
OUT
AC
IN AC
OUT
AC
INPUT
POWER
AC OUTPUT
STATUS

Page 17
Display shows battery voltage (12.8V), use
Note: In Inverter/Battery Mode, the ‘Power’ button can be used to temporarily turn the unit O to save battery
power if AC Output power is not required. When AC Input Source or Shore Power returns, unit will automatically turn On
and run in By-Pass Mode again.
- ‘Power’ indicator on indicates unit is On.
- If ‘AC Output’ indicator is On, indicator is On, it indicates AC Output Switch is turned On (AC is available
at the output socket and the output hardwire terminal).
- If ‘AC Output’ indicator is O, it indicates the AC Output AC Output Switch is turned O (AC is not
available at the output socket and the output hardwire terminal).
- Press and hold ‘Escape’ button for 5 seconds to toggle AC Output Switch On and O.
- If ‘Status’ indicator is solid amber, it indicates inverter is running.
- If ‘Status’ indicator changes to ashing amber, it indicates AC Input Source is detected and will switch
back to By-Pass Mode shortly.
- is On indicates inverter is providing AC Power.
- icon indicates estimated battery capacity.
AC Output Power.
or button to see DC Current discharge from battery,
AC
OUT
AC
OUT
POWER
AC OUTPUT
STATUS
(ii) Automatic Backup with Battery Charger Function Disabled –
(‘INT’ = ‘ABU’, ‘CHG’ = ‘OFF’)
This is a setting when a second Battery Charging source is use and the unit’s built-in AC Charger function is disabled at all times.
Please note that a second battery charging source is required to charge the battery. The Inverter will automatically turn on when AC
Input source or shore power is interrupted. This provides smooth, uninterrupted AC power to the load. The inverter is in standby
condition.
- Display shows battery voltage (12.5V), use
Note: When this setting is used, AC Charger is disabled. A separate Battery Charger or other battery charging source is
required to charge the battery.
- ‘Power’ indicator on indicates unit is On.
- If ‘AC Output’ indicator is On, it indicates the AC Output Switch is turned On (AC is available at the
output socket and the output hardwire terminal).
- If ‘AC Output’ indicator is O, it indicates the AC Output Switch is turned O (AC is not available at the
output socket and the output hardwire terminal).
- Press and hold ‘Escape’ button for 5 seconds to toggle AC Output Switch On and O.
- If ‘Status’ indicator is solid green, it indicates the unit is running in By-Pass Mode.
- is On indicates AC Input Source is in use.
- is On indicates AC Output is getting the power from AC Input source.
- icon indicates estimated battery capacity.
charger is disabled), AC Input Power.
or button to see DC Current (always 0A because
INT ABU
CHG OFF Automatic Backup with Battery Charger Function Disabled
When AC Input Source or Shore Power is available, unit is running in By-Pass Mode. AC Output is getting the power from the AC
Input Source or Shore Power. Charger is disabled. Inverter is in standby condition.
AC
INPUT
AC
IN AC
OUT
AC
IN AC
OUT
AC
INPUT
POWER
AC OUTPUT
STATUS
Note: In By-Pass Mode, the ‘Power’ button function is disabled. It cannot be used to turn O the unit.

Enerdrive Inverter-Charger Owners Manual (Rev. 1.0)Page 18
(iii) Manual Backup with Battery Charger Function Enabled –
(‘INT’ = ‘MBU’, ‘CHG’ = ‘ON’)
This is another commonly used setting on the unit. The charger function is enabled when AC Input Source or Shore Power is available.
When there is a blackout, the inverter will not turn On automatically. It requires the user to manually turn on the inverter function
when needed.
When there is a blackout (AC Input Source or Shore Power is not available), unit is running in Inverter/Battery Mode. Unit has
automatically switched to getting AC Power from the inverter.
INT MBU
CHG ON Manual Backup with Battery Charger Function Enabled
When AC Input Source or Shore Power is available, unit is running in By-Pass Mode. AC Output is getting the power from the AC
Input Source or Shore Power. Charger is enabled. Inverter is disabled.
Display shows battery voltage (12.8V), use
Note: In Inverter/Battery Mode, the ‘Power’ button can be used to temporarily turn the unit O to save battery
power if AC Output power is not required. When AC Input Source or Shore Power returns, unit will automatically turn On
and run in By-Pass Mode again.
- ‘Power’ indicator on indicates unit is On.
- If ‘AC Output’ indicator is On, indicator is On, it indicates AC Output Switch is turned On (AC is available
at the output socket and the output hardwire terminal).
- If ‘AC Output’ indicator is O, it indicates the AC Output AC Output Switch is turned O (AC is not
available at the output socket and the output hardwire terminal).
- Press and hold ‘Escape’ button for 5 seconds to toggle AC Output Switch On and O.
- If ‘Status’ indicator is solid amber, it indicates inverter is running.
- If ‘Status’ indicator changes to ashing amber, it indicates AC Input Source is detected and will switch
back to By-Pass Mode shortly.
- is On indicates AC Input Source is in use.
- is On indicates inverter is providing AC Power.
- icon indicates estimated battery capacity.
AC Output Power.
or button to see DC Current discharge from battery,
AC
OUT
AC
OUT
AC
INPUT
POWER
AC OUTPUT
STATUS
- Display shows battery voltage (14.2V), use
- is On indicates AC Input Source is in use.
- is On indicates AC Output is getting the power from AC Input source.
- is On indicates the charger is enabled and is charging the battery.
- icon indicates the charging stage of the battery
AC Input Power.
or button to see DC Current charging the battery,
AC
AC
AC
INPUT
AC
IN AC
OUT
AC
IN AC
OUT
AC
INPUT
Note: In By-Pass Mode, the ‘Power’ button function is disabled. It cannot be used to turn O the unit.
- ‘Power’ indicator on indicates unit is On.
- If ‘AC Output’ indicator is On, it indicates the AC Output Switch is turned On (AC is available at the
output socket and the output hardwire terminal).
- If ‘AC Output’ indicator is O, it indicates the AC Output Switch is turned O (AC is not available at the
output socket and the output hardwire terminal).
- Press and hold ‘Escape’ button for 5 seconds to toggle AC Output Switch On and O.
- If ‘Status’ indicator is solid green, it indicates battery is fully charged.
- If ‘Status’ indicator is ashing green, it indicates battery charging is in progress.
POWER
AC OUTPUT
STATUS

Page 19
- Display shows battery voltage (12.6V), use or button to see DC Current (always 0A because
charger is O), AC Input Power (always 0W because Inverter is disabled).
- icon indicates estimated battery capacity.
Note: Under this condition, Display and unit will turn O after 10 seconds.
At any time, if an AC Input Source is detected, unit will switch back to By-Pass Mode automatically in about 10 seconds.
During the 10 second period, ‘Power’ indicator turns On and ‘Status’ indicator remains O.
- ‘Power’ indicator on indicates unit is On.
- ‘AC Output’ indicator is O (AC Output is not available due to the inverter being set to Manual Backup
Mode – MBU).
- ‘Status’ indicator is O.
When there is a blackout (AC Input Source or Shore Power is not available), unit will not provide AC Backup as Inverter is disabled.
Display remains On for 10 seconds with the following appearance:
If AC Output is required during a blackout, press and hold the ‘Power’ button for one second to manually turn On the inverter.
- Display shows battery voltage (12.8V), use or button to see DC Current discharged from battery,
AC Output Power.
- is on indicates inverter is providing AC Power.
- icon indicates estimated battery capacity.
POWER
AC OUTPUT
STATUS
- ‘Power’ indicator on indicates unit is On.
- If ‘AC Output’ indicator is On, it indicates AC Output Switch is turned On (AC is available at the output
socket and the output hardwire terminal).
- If ‘AC Output’ indicator is O, it indicates AC Output Switch is turned O (AC is not available at the
output socket and the output hardwire terminal).
- Press and hold ‘Escape’ button for 5 seconds to toggle AC Output Switch On and O.
- If ‘Status’ indicator is solid amber, it indicates inverter is running.
- If ‘Status’ indicator changes to ashing amber, it indicates AC Input Source is detected and will switch
back to By-Pass Mode shortly.
POWER
AC OUTPUT
STATUS
AC
OUT
AC
OUT
Note: The ‘Power’ button can be used to turn the unit O if AC Output power is not required. When AC Input Source or
Shore Power returns, unit will automatically turn On and run in By-Pass Mode again.
(iv) Manual Backup with Battery Charger Function Disabled –
(‘INT’ = ‘MBU’, ‘CHG’ = ‘OFF’)
When there is a blackout, the inverter will not turn On automatically. It requires the user to manually turn on the inverter function
when needed. The unit’s built-in AC Charger function is disabled at all times. Please note that a second battery charging source is
required to charge the battery.
INT MBU
CHG OFF
Manual Backup with Battery Charger Function Disabled
- Display shows battery voltage (12.5V), use or button to see DC Current (always 0A because
charger is disabled), AC Input Power.
charger is O), AC Input Power (always 0W because Inverter is disabled).
-is on indicates AC Input Source is in use.
-is on indicates AC Output is getting the power from AC Input source.
-icon indicates estimated battery capacity.
AC
OUT
Note: When this setting is used, AC Charger is disabled. A separate Battery Charger or other battery charging source is
required to charge the battery.
AC
INPUT
AC
OUT
AC
INPUT

Enerdrive Inverter-Charger Owners Manual (Rev. 1.0)Page 20
When there is a blackout (AC Input Source or Shore Power is not available), unit will not provide AC Backup as Inverter is
disabled. Display remains On for 10 seconds with the following appearance:
If AC Output is required during a blackout, press and hold the ‘Power’ button for one second to manually turn On the inverter.
- ‘Power’ indicator on indicates unit is On.
- If ‘AC Output’ indicator is On, it indicates AC Output Switch is turned On (AC is available at the output
socket and the output hardwire terminal).
- If ‘AC Output’ indicator is O, it indicates AC Output Switch is turned O (AC is not available at the
output socket and the output hardwire terminal).
- Press and hold ‘Escape’ button for 5 seconds to toggle AC Output Switch On and O.
- ‘Status’ indicator is solid green indicates unit is running in By-Pass Mode.
POWER
AC OUTPUT
STATUS
Note: In By-Pass Mode, the ‘Power’ button function is disabled in this stage. It cannot be used to turn O the unit.
- ‘Power’ indicator on indicates unit is On.
- ‘AC Output’ indicator is O (AC Output is not available due to the inverter being set to Manual Backup
Mode – MBU).
- ‘Status’ indicator is O
POWER
AC OUTPUT
STATUS
Note: Under this condition, Display and unit will turn O after 10 seconds.
At any time, if an AC Input Source is detected, unit will switch back to By-Pass Mode automatically in about 10 seconds.
During the 10 second period, ‘Power’ indicator turns On and ‘Status’ indicator remains O.
Note: The ‘Power’ button can be used to turn the unit O if AC Output power is not required. When AC Input Source or
Shore Power returns, unit will automatically turn On and run in By-Pass Mode again.
- Display shows battery voltage (12.6V), use or button to see DC Current (always 0A because
charger is O), AC Input Power (always 0W because Inverter is disabled).
- icon indicates estimated battery capacity.
- ‘Power’ indicator on indicates unit is On.
- If ‘AC Output’ indicator is On, it indicates AC Output Switch is turned On (AC is available at the output
socket and the output hardwire terminal).
- If ‘AC Output’ indicator is O, it indicates AC Output Switch is turned O (AC is not available at the
output socket and the output hardwire terminal).
- Press and hold ‘Escape’ button for 5 seconds to toggle AC Output Switch On and O.
- If ‘Status’ indicator is solid amber, it indicates inverter is running.
- If ‘Status’ indicator changes to ashing amber, it indicates AC Input Source is detected and will switch
back to By-Pass Mode shortly.
POWER
AC OUTPUT
STATUS
- Display shows battery voltage (12.8V), use or button to see DC Current discharged from
battery, AC Output Power.
- is on indicates inverter is providing AC Power.
- icon indicates estimated battery capacity.
AC
OUT
AC
OUT
(v) No Backup with Battery Charger Function Enabled –
(‘INT’ = ‘OFF’, ‘CHG’ = ‘ON’)
The unit is used as a Battery Charger with AC Transfer Switch only. AC Output Power is available when AC Input Source or Shore Power
is available. The Charger function is enabled when AC Input Source or Shore Power is available. Inverter function is disabled.