Dometic CT 4050 User manual

CT4050, CTLP4110, CTS4110
Cassette toilet
Installation Manual
EN
SANITATION
TOILETS
CT4000-I-AUS.book Seite 1 Donnerstag, 1. Juni 2017 3:05 15

CT4000-I-AUS.book Seite 2 Donnerstag, 1. Juni 2017 3:05 15

EN
CT4000
3
Please read this instruction manual carefully before installation and first
use, and store it in a safe place. If you pass on the product to another
person, hand over this instruction manual along with it.
Table of contents
1 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2.1 General safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2.2 Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3 Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
4 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
4.1 Description of the components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5 Installing the toilet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
5.1 Installing the service door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
5.2 Making wall cutouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
5.3 Setting up the toilet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
5.4 Installing CT model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
5.5 Installing models CTLP, CTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
5.6 Connecting the water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.7 Venting the cartridge tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
6 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.1 Connecting external water pump. . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7Technicaldata. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
CT4000-I-AUS.book Seite 3 Donnerstag, 1. Juni 2017 3:05 15

EN
Explanation of symbols CT4000
4
1 Explanation of symbols
!
A
I
2 Safety instructions
The manufacturer accepts no liability for damage in the following cases:
•Faulty assembly or connection
•Damage to the product resulting from mechanical influences and excess voltage
•Alterations to the product without express permission from the manufacturer
•Use for purposes other than those described in the operating manual
The declaration of conformity can be requested from the manufacturer (contact
information on the back).
2.1 General safety
!CAUTION!
•This device can be used by children aged 8 years or over, as well as by
persons with diminished physical, sensory or mental capacities or a
lack of experience and knowledge, providing they are supervised or
have been taught how to use the device safely and are aware of the
resulting risks.
•Cleaning and user maintenance must not carried out by unsupervised
children.
•Children must be supervised to ensure that they do not play with the
device.
•The toilet may be installed only by trained personnel.
CAUTION!
Safety instruction: Failure to observe this instruction can lead to injury.
NOTICE!
Failure to observe this instruction can cause material damage and impair
the function of the product.
NOTE
Supplementary information for operating the product.
CT4000-I-AUS.book Seite 4 Donnerstag, 1. Juni 2017 3:05 15

EN
CT4000 Intended use
5
ANOTICE!
•All components of the system must be installed in frost-free areas. In
freezing temperatures, there is a risk of damage caused by frost.
•Do not use antifreeze. These agents may damage the cassette toilet.
•The operating pressure (water pressure) of the solenoid valve should
not exceed 6 bar. The solenoid valve is damaged by excessive
pressure.
•The electrical installation must comply with national and local
regulations.
In Europe: EN 1645-1, EN 1646-1, EN 1648-1, EN 1648-2
2.2 Installation instructions
The toilet must be installed so that it is accessible for service work, is easy to de-install
and install, and can be removed from the vehicle without much effort.
3 Intended use
The toilet is designed for installation and use in recreational vehicles such as camper
vans or motor caravans.
4 Technical description
The cassette toilet CTx 4xxx consists of a toilet permanently installed in the vehicle
and a removable, mobile cassette as a holding tank. The cassette is externally acces-
sible through a door. Depending on the model, the toilet is supplied with rinse water
from the vehicle-side freshwater tank or a tank integrated in the housing.
The following model versions of the toilet are available:
•CT4050: detached, without water tank, without console
•CTLP4110: detached, without water tank, low console
•CTS4110: detached, without water tank, with console
The 4050 models can be installed in a wet room.
CT4000-I-AUS.book Seite 5 Donnerstag, 1. Juni 2017 3:05 15

EN
Technical description CT4000
6
4.1 Description of the components
No. in fig. 1Designation
1 Housing for cassette tank
2 Draining slider for toilet bowl
3 Toilet bowl, ceramic
4 Lid and seat, rotatable
5Console
6 Control and operating panel
7 CTLP, CTS only: Wall bracket
8 Cassette tank (capacity 19 l)
9 Service door (accessories)
6
9
8
4
5
3
2
1
7
1
CT4000-I-AUS.book Seite 6 Donnerstag, 1. Juni 2017 3:05 15

EN
CT4000 Installing the toilet
7
5 Installing the toilet
5.1 Installing the service door
Model-dependent installation instructions are included with the service door
(Dometic SK4, SK5).
I
5.2 Making wall cutouts
➤Follow the instructions of the installation manual that comes with the service
door.
➤Make a rectangular opening in the outer wall with the following dimensions
(fig. 2):
Service door wall cutout SK4:
–y=25mm
– b = 305 mm ± 1 mm
– h = 375 mm ± 1 mm
Service door wall cutout SK5:
–y
min = 12.5 mm, ymax = 28 mm
– b = 310 mm ± 1 mm
– h = 360 mm ± 1 mm
The dimension x results from the placement of the toilet.
NOTE
Prepare the feed-through for the vent hose at the desired location
(chapter “Venting the cartridge tank” on page 21).
x
h
y
b
2
CT4000-I-AUS.book Seite 7 Donnerstag, 1. Juni 2017 3:05 15

EN
Installing the toilet CT4000
8
5.3 Setting up the toilet
A
I
➤Install the toilet according to the description for the respective model version.
➤Set up the toilet so that it is flush to a vertical wall only.
➤Leave enough space so that actuation of the draining slider is not restricted.
➤For the installation, use the dimensional drawings:
NOTICE!
All components of the system must be installed in frost-free areas. In
freezing temperatures, there is a risk of damage caused by frost.
NOTE
•When installing the toilet in a wet room, the manufacturer recom-
mends that you connect the toilet to the shower tray.
•The toilet base is equipped with a protruding collar for receiving the
upper edge of the shower tray (fig. 3).
3
CT4000-I-AUS.book Seite 8 Donnerstag, 1. Juni 2017 3:05 15

EN
CT4000 Installing the toilet
9
CT4050: fig. 4
110
875,1
335,2
530
505
381,6
409,2 406,2
376,9 ≥ 115
381,6
90°
(3)
4
CT4000-I-AUS.book Seite 9 Donnerstag, 1. Juni 2017 3:05 15

EN
Installing the toilet CT4000
10
CTLP4110: fig. 5
110
875,1
500
530
505
381,6
529,2 526,2
385 112 (3)
381,6
90°
5
CT4000-I-AUS.book Seite 10 Donnerstag, 1. Juni 2017 3:05 15

EN
CT4000 Installing the toilet
11
CTS4110: fig. 6
110
875,1
671,9
530
505
381,6
529,2 526,2
385 112 (3)
381,6
90°
6
CT4000-I-AUS.book Seite 11 Donnerstag, 1. Juni 2017 3:05 15

EN
Installing the toilet CT4000
12
5.4 Installing CT model
The detached model CT4050 has no integrated water tank and no console. Set up
this model so that the wall behind it can accommodate the control unit of the toilet,
the electrical connections and possibly a water tank. It is best if you put a box in front
of the room wall (fig. 7).
7
CT4000-I-AUS.book Seite 12 Donnerstag, 1. Juni 2017 3:05 15

EN
CT4000 Installing the toilet
13
➤Align the toilet according to the service door.
➤Place the housing base flush with the installation box so that there is a clean
transition and no gap.
50
110
8
CT4000-I-AUS.book Seite 13 Donnerstag, 1. Juni 2017 3:05 15

EN
Installing the toilet CT4000
14
Attaching toilet CT 4050
➤Place the toilet in the desired position.
➤Tightly fasten the base plate with six bolts (fig. 9).
➤Bolt the toilet housing to the wall (using a maximum of 7 bolts, not included)
(fig. 0).
6x
9
38 x
∅4,5
0
CT4000-I-AUS.book Seite 14 Donnerstag, 1. Juni 2017 3:05 15

EN
CT4000 Installing the toilet
15
Installing the control and operating panel of the CT 4050 toilet
Install the control and operating panel in the wall in the immediate vicinity of the toilet
at an easily accessible location.
➤Use a copy of the 1:1 scale template (fig. a) to make the wall cutout.
a
CT4000-I-AUS.book Seite 15 Donnerstag, 1. Juni 2017 3:05 15

EN
Installing the toilet CT4000
16
➤Prepare an opening in the installation box for the control and operating panel
(fig. b).
➤Connect the electrical cables to the connections of the control and operating
panel (chapter “Electrical connection” on page 22).
!
➤Press in the retaining springs of the control and operating panel and push it into
the wall cutout.
➤Follow the instructions in (chapter “Connecting the water supply” on page 20).
CAUTION!
There is a risk of injury due to the springs springing back!
60
R10
74
2.
1.
3.
b
CT4000-I-AUS.book Seite 16 Donnerstag, 1. Juni 2017 3:05 15

EN
CT4000 Installing the toilet
17
➤Slide in the mobile tank cassette (fig. c).
5.5 Installing models CTLP, CTS
These models have a wall connection console. The control and operating panel is
integrated in the wall connection console.
Set up all models with wall connection console directly against the room wall.
A previously attached wall bracket is used to secure the toilet and the wall bracket.
➤Screw on the wall bracket, level, at the following height (fig. d):
–CTLP4110: h = 479.5 mm
–CTS4110: h = 651.5 mm
c
==
90
h
d
CT4000-I-AUS.book Seite 17 Donnerstag, 1. Juni 2017 3:05 15

EN
Installing the toilet CT4000
18
➤Put the entire toilet module into the desired position in front of the wall bracket.
➤Lift the toilet and hook the housing into the wall bracket (fig. e).
➤Tightly fasten the base plate with six bolts (fig. f).
2
1
e
6x
f
CT4000-I-AUS.book Seite 18 Donnerstag, 1. Juni 2017 3:05 15

EN
CT4000 Installing the toilet
19
➤Place the two covers over the fastening screws in the base plate (fig. g).
➤Follow the instructions in (chapter “Connecting the water supply” on page 20).
➤Slide in the mobile tank cassette (fig. h).
2x
g
h
CT4000-I-AUS.book Seite 19 Donnerstag, 1. Juni 2017 3:05 15

EN
Installing the toilet CT4000
20
5.6 Connecting the water supply
A
➤Use a spring band hose clamp to attach the freshwater supply hose to the
connection socket (fig. i2).
➤Perform a leak test.
NOTICE!
•The water supply is connected using a solenoid valve mounted in the
toilet housing (fig. i1).
•The operating pressure (water pressure) of the solenoid valve should
not exceed 6 bar.
•The solenoid valve is damaged by excessive pressure.
2
1
i
CT4000-I-AUS.book Seite 20 Donnerstag, 1. Juni 2017 3:05 15