DoorHan Sectional-750 User manual
InstallatIon and
operatIng manual
seCtIonal-750/1200/Fast-750
2
1
TableofconTenTs
3 3
1
InTenDeDUse
This manual is for operators DOORHAN SECTIONAL
GENERAL SAFETY INSTRUCTIONS ON ITEM INSTALLATION
For safe operation of automatic gates do follow installation instructions contained in this manual.
During installation:
After installation is completed:
IMPORTANT! RISK OF DAMAGE.
KIT COMPOSITION
4
1
Tools
Tools required for installation of operator SECTIONAL:
Materials for installation of operator SECTIONAL and accessories (if available):
This operator complies with the requirements of European Directives 98/73/EC, 89/336/EC, 1999/5/EC
SAFETY AT INSTALLATION
5 5
1
sPecIfIcaTIons
Model Sectional-750 Sectional-1200
Supply voltage range, V
Current frequency, Hz
Motor voltage (V dc)
Maximum consumed power (W)
Force (Н) max.
Duty type
Light lamp (V ~/W)
Cartridge type
Lamp interrupting time (sec)
Basic speed of slide (m/min)
Corresponding safety device
Maximal gate width (mm)
Maximal gate height (mm)
Guide working travel (mm)
Protection rate
Working temperature range (°C)
Fuse type
Transmitter frequency/range
Operator type
SPECIFICATIONS
DIMENSIONS
Operator Recommended gate area (m2)
Guide
Model G - Length L – Working travel Max. gate height
6
1
DescrIPTIon
DESCRIPTION
ASSEMBLY
Pre-check
7 7
1
connecTIonofoPeraTorTogUIDe
INSTALLATION
CONNECTION OF OPERATOR TO GUIDE
8
1
ManUalreleasIngaUToMaTIcsysTeM
In case of power outage:
After restoration of supply:
In the case of power failure
If power recovers
MANUAL RELEASING AUTOMATIC SYSTEM
External release (optional)
CONTROL UNIT
Specifications
9 9
1
WIrIng
WIRING
INSTALLATION OF PHOTOCELLS (IF SUPPLIED):
Installation
Maintenance
Recommendation by operation:
Com
No
Nc
Motor
GND
5V
IR
230 V (L/N)
Door
GND
+24
GND
+24
COM
Out
NO
+12V
PE
Reciever 433 MHz
Main panel
Button control
Photocell
10
1
PrograMMIng
PROGRAMMING
Preparation
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
Upper Limit Setting
Press key“p”
(about 5 seconds)
The unit beeps once
and shows “1”
Press “p”, “1” flashes Press “+”
Or press “�”
Door goes up When the door risesto
an ideal position, press
key“P” to save
the Information
Press “�”to show “2” Press “p”,”2” flashes Press “�”
Or press “+” Door goes down When the door descends
toan ideal position,
after 2 seconds press key
“P”to savethe information
Down Limit Setting
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
Operating Force Learning
Press “�”, shows “3” Press“p”, “3” flashes Door rises automatically Press “p” after stops,
press “p” again Door descends Press “P”to save the
information, refer to
After the above basic settings,the user can now carry out the finalizing stepto finalizethe programming
RRR
+++
PPP
���
11
S
P
+
�
S
P
+
�
The unit has been preset on the factoryat level 4,resetting by end users is not required.
Force Level Setting
Press “�” to show “4”
Transmitter Control Button Settings Setinthe factory
Low
Force level High
Press “�” to show “5”
Press “p”, “2” flashes,it
meansnow thedoor
control channel is set
at thesecond buttonofthe transmitter
Press “+”or “�”,to choose
a desired button from 1to4 The motor has been set at channel 2at the factory
to control the door,“0” meansno channelis chosen
P
+
�
P
+
�
R
R
3 sec
3 sec
Press
Manual adjustment (max force level 60 kg)
press “+” or “�” for changing force level
Automatic adjustment (max force level 20 kg)
Set in the factory
press “+” or “�” for changing force level
Press to “p”to save the settings
If the force level is set too low, the door moving
will be affected whenthe mechanical
structure of the door is not well�balanced
Press “p”
11 11
1
PrograMMIng
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
Upper Limit Setting
Press key“p”
(about 5 seconds)
The unit beeps once
and shows “1”
Press “p”, “1” flashes Press “+”
Or press “�”
Door goes up When the door risesto
an ideal position, press
key“P” to save
the Information
Press “�”to show “2” Press “p”,”2” flashes Press “�”
Or press “+” Door goes down When the door descends
toan ideal position,
after 2 seconds press key
“P”to savethe information
Down Limit Setting
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
Operating Force Learning
Press “�”, shows “3” Press“p”, “3” flashes Door rises automatically Press “p” after stops,
press “p” again Door descends Press “P”to save the
information, refer to
After the above basic settings,the user can now carry out the finalizing stepto finalizethe programming
RRR
+++
PPP
���
11
S
P
+
�
S
P
+
�
The unit has been preset on the factoryat level 4,resetting by end users is not required.
Force Level Setting
Press “�” to show “4”
Transmitter Control Button Settings Setinthe factory
Low
Force level High
Press “�” to show “5”
Press “p”, “2” flashes,it
meansnow thedoor
control channel is set
at thesecond buttonofthe transmitter
Press “+”or “�”,to choose
a desired button from 1to4 The motor has been set at channel 2at the factory
to control the door,“0” meansno channelis chosen
P
+
�
P
+
�
R
R
3 sec
3 sec
Press
Manual adjustment (max force level 60 kg)
press “+” or “�” for changing force level
Automatic adjustment (max force level 20 kg)
Set in the factory
press “+” or “�” for changing force level
Press to “p”to save the settings
If the force level is set too low, the door moving
will be affected whenthe mechanical
structure of the door is not well�balanced
Press “p”
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
R
P
+
�
Alarm Settings
Automatic Closing Time Settings
Press “�”, shows “6” Press“p”,it shows0,
it means the alarm
settings are off
Press “+”, it shows1,it means
the alarm setting are on
Press “�”, shows “7” Press“P” to show “0”,
it means the
functionis off
Press “+” to show “1” to turn
the functionon, it also means the
auto closing time is 30 seconds
2000 Cycles Alarm Setting
Press “�”, shows “8” Press“p”,it shows 0,
it means the
function is off
Press “+” ,it shows1,it means this function is on
If the not closed in 10 minutes, system turnsonalarm sound.
The inclusion of high speed opening/closing (only for FAST 750)
12
1
ManUfacTUrer’sWarranTy
START
REPAIRS
MAINTENANCE
DISPOSAL
MANUFACTURER’S WARRANTY
R
P
+
�
RR
PP
++
��
R
P
+
�
R
P
+
�
Final Programming
(NB: This finalizing step must be carriedout, otherwise the saved information
will be lost)
Programming of Transmitters
Press“S” “0” willbe shownon the
left side of the display,
and disappears immediately
Press any key twice,
coding is completed.
At this time, the code isuccessfullyset if opener works.
Other transmitters canbeset as above.
Decode
Press & hold “R”
for8seconds
0” willbe shown on the
left side of the display.
Keep pressing the key
until “0” disappeares
For security purpose if a transmitter has been lost theopener must be decoded
and the new transmitter encoded as above,so that the lost one
can not operate thedoor anymore.
By now,no transmitterscan operate the opener unless re�coded.
R
P
+
�
R
P
+
�
R
P
+
�
13 13
1
PossIbleMalfUncTIonsanDTrooblesHooTIng
Malfunction Possible reason Solution
POSSIBLE MALFUNCTIONS AND TROOBLE SHOOTING
14
1
noTes
15 15
1
noTes
120 Novaya street, Akulovo village, Odintsovo district,
Moskow region, 143002 Russia
Tel: +7(495)933–2400, 981–1133
E–mail: [email protected]
www.doorhan.com
This manual suits for next models
2
Table of contents
Other DoorHan Gate Opener manuals
DoorHan
DoorHan SHAFT-120 User manual
DoorHan
DoorHan SWING-3000 User manual
DoorHan
DoorHan SWING-3000PRO User manual
DoorHan
DoorHan PCB-SH Installation manual
DoorHan
DoorHan SHAFT-30 User manual
DoorHan
DoorHan SHAFT-30 User manual
DoorHan
DoorHan SLIDING-1300 User manual
DoorHan
DoorHan SECTIONAL-500PRO User manual
DoorHan
DoorHan SLIDING-3000 User manual
DoorHan
DoorHan Sectional-1000 User manual
Popular Gate Opener manuals by other brands
Beninca
Beninca RI.15T Operating instructions and spare parts catalogue
LOCKEY USA
LOCKEY USA TB-950 Magnum installation instructions
DITEC
DITEC OBBI Technical manual
Centsys
Centsys D5-Evo Synchronisation Diagram
RAMSET
RAMSET RAM 300 instruction manual
Erreka
Erreka VIVO-D102 Quick installation and programming guide