Dormakaba STV 50 Series User manual

WN 059725 45532 – 2018-11
EN
STV50x
Mounting instructions
Contents
1 About this document 1
2 Safety 1
3 Product description 2
4 Mounting 2
5 Disassembly, recycling and disposal 7
1 About this document
1.1 Contents and purpose
This document describes the mounting of the
electromechanical locking device STV 50x and the
connection to a SafeRoute® system.
1.2 Target group
This document is intended for assembling technicians
and specialists authorized for mounting by
dormakaba.
1.3 Other applicable documents
The following documents belong to the unit’s
complete documentation and must be observed:
• The SafeRoute® system manual
• The respective door unit’s inspection log
1.4 Documents storage
This document must be handed over to the facility
operator after mounting and commissioning.
1.5 Symbols used
1. 2. Sequence of action steps
6Reference to a chapter
Door opening direction DIN left =
opening outwards to the right
Door opening direction DIN right =
opening outwards to the left
Components may be damaged by
electrostatic discharge. Ground
your own body before touching a
component!
2 Safety
2.1 Intended use
The STV50x is an electromechanical locking device
based on the quiescent current principle.
2.2 Requirements for fire and smoke
protection doors
When mounting the STV 50x in preventive fire
protection, the fire and smoke protection doors’
properties must not be impaired. Mounting is only
permitted if the proof of usability for the fire and
smoke protection door allows for installation and the
proof of usability’s stipulations are observed. Further
information can be found in the report “Permissible
changes and additions to fire protection closures”
from the Deutsches Institut für Bautechnik (DIBt
1/1996), Berlin.
2.3 Personnel qualification
Mounting may only be carried out by persons
authorized by dormakaba.

2STV50x 2018-11
WN 059725 45532
dormakaba Mounting instructions Product description
3 Product description
The STV50x is an electromechanical locking device for
swing doors, which is concealed in the door frame. A
TV-Z510 mortise latch lock is required in the door leaf
as a counterpart. The STV50x is a DCW® component
in a SafeRoute® system.
3.1 Variants
STV 501 with angled strike plate for DIN-L folding
doors
STV 502 with angled strike plate for DIN-R folding
doors
STV 505 with flat striking plate for DIN-L rebated
doors
STV 506 with flat striking plate for rebated doors
DIN-R
STV 507 with flat striking plate and latch guide for
rebated doors DIN-L
STV 508 with flat striking plate and latch guide for
rebated doors DIN-R
Fig. 1
STV
502
STV
506
STV
508
Variants for doors (DIN right)
3.2 Parts included
• STV50x in one of the above mentioned variants
• Bag with fixing materials
3.3 Technical information
Locking force:
Supply voltage:
2000N at UB +/-10 %
24VDC +/-15 %
Power consumption: 75 mA
Temperature range: -10°C to +55°C
Rel. humidity: up to 93 % (non
condensing)
Protection class: IP 30 in installed condition
with door closed
4 Mounting
The mounting is shown on a door which opens
outwards to the left (DIN right).
When mounting on a door which opens outwards to
the right (DIN left), proceed mirror-inverted!
4.1 Mounting position
Fig. 2
STV-50x
TV-Z 510
STV
505
Example for STV50x mounting position
4.2 Please note during mounting
Fig. 3
STV-50x
TV-Z 510
STV
505
STV-50x
TV-Z 510
STV
505
Notes on mounting the STV50x

3STV50x 2018-11WN 059725 45532
dormakaba Mounting instructions Mounting
4.3 Mounting the variants
4.3.1 Mount STV501 or STV502
1
STV 501
STV 502
approx. 100mm
Ø 3mm
2A
4.
3.
5. 6.
2
approx. 180mm
4.
3.
5. 6.

4STV50x 2018-11
WN 059725 45532
dormakaba Mounting instructions Mounting
4.3.2 Mount STV505 or STV506
STV 505
STV 506
1
4.4
approx. 100mm
Ø 3mm
1.
2.
STV 505
STV 506
2
Exchange only as a complete unit.
Do not separate the striking plate from the
locking unit!
4.
3.
approx. 180 mm

5STV50x 2018-11WN 059725 45532
dormakaba Mounting instructions Mounting
4.3.3 Mount STV507 or STV508
1
STV 507
STV 508
4.4
approx. 100mm
Ø 3mm
3.
2
1.
STV 507
STV 508
approx. 180mm
4.
2.
Exchange only as a complete unit.
Do not separate the striking plate from the
locking unit!

6STV50x 2018-11
WN 059725 45532
dormakaba Mounting instructions Mounting
4.4 Assignment of terminals and switch/button
A
1
3
B
19
18
+24VDC
GND
DCW® bus
external door contact or bridge
A
1
3
B
+24VDC
GND
DCW® bus
DCW®
address
Switch
1
ON
1
0
2
1
2
3
4
0
1
0
1
0
0
1
1
DCW® DIP switch
If multiple electrical door locks (STV xxx) are connected via the DCW® bus, assign
different DCW® bus addresses to the electrical door locks.
Service button (press service button for 8 seconds = factory setting)
LED displays
LED On LED Off LED flashes
DCW® LED (red)
Bus connection OK
Bus connection interrupted
DCW® error
Config LED (yellow)
Configuration successful
Device not configured
Both LEDs
Configuration mode active
4.5 Complete mounting
1. Document the mounting and commissioning in
the inspection log.
2. Hand over this document to the facility operator.

7STV50x 2018-11WN 059725 45532
dormakaba Mounting instructions Disassembly, recycling and disposal
5 Disassembly, recycling and
disposal
Disassembly is carried out in the reverse order of
mounting and must be carried out by qualified
personnel.
The product must be disposed of in an
environmentally friendly manner. Electro-
technical parts and batteries must not be
disposed of as domestic waste. Dispose of
electrotechnical parts and batteries in the designated
acceptance and collection points. Refer to the
statutory regulations for your country.

dormakaba Deutschland GmbH
DORMA Platz 1 58256 Ennepetal Germany T: [phone] F: [phone] www.dormakaba.com Translation of the original document, subject to change without notice