Assa Abloy Sargent 11 Line User manual

1-800-727-5477 • www.sargentlock.com A7668B 3/20
Copyright © 2009, 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction
in whole or in part without the express written permission ofSARGENT Manufacturing Company is
prohibited. 1
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information go
to www.P65warnings.ca.gov.
Note
• Factory assembled for either right
or left hand doors. Correct hand to
match door application.
• Improper installation may result
in damage to lock and void factory
warranty.
• Other product brand names
may be trademarks or registered
trademarks of their respective
owners and are mentioned for
reference only.
11 Line
with High Security Lever (SL-) Attachment
Bored Lock
Installation Instructions

1-800-727-5477 • www.sargentlock.com A7668B 3/20
Copyright © 2009, 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction
in whole or in part without the express written permission ofSARGENT Manufacturing Company is
prohibited. 2
11 Line w/ SL- Option
Installation Instructions
Bored Lock
TOC Table of Contents
1 Lock Body Assembly .............................................................2
2 Security Attachment Screw......................................................2
3 Lever Installation ................................................................3
4 Cylinder Removal................................................................3
Lock Body Assembly
1
1. Prep door, and install lock bearing and latch according to T-Zone Installation
Instructions A7469, steps 1through 5.
2. Complete assembly of lock with Security Lever Attachment, according to
the following steps.
Security Attachment Screw
2
1. Using screwdriver provided, unscrew the Security Attachment Screw from lever catch on the outside
sleeve.
IMPORTANT - Keep screw for reinstallation.
2. Install outside and inside sleeves and roses according to Installation Instructions A7469, steps 6 & 7.
3. PLEASE NOTE - THE CAM IN THE OUTSIDE SLEEVE MUST BE ROTATED SO THE LARGE SLOT IS
HORIZONTAL. THIS ALLOWS THE SECURITY SCREW TO THREAD INTO THE CAM.
Insert the Security Attachment Screw into black lever catch assembly and tighten until screw head is
within approximately 1/8” of black lever catch. DO NOT OVER TIGHTEN.

1-800-727-5477 • www.sargentlock.com A7668B 3/20
Copyright © 2009, 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction
in whole or in part without the express written permission ofSARGENT Manufacturing Company is
prohibited. 3
Lever Installation
3
1. IMPORTANT: Before installing levers read, “SPECIFIC INSTRUCTIONS PER FUNCTION -
BEFORE INSTALLING LEVER” on page 4 of T-Zone Installation Instructions A7469.
2. Place cylinder in outside lever. Insert key and rotate 45 degrees clockwise.
3. With key rotated, push lever onto sleeve until hole on inside of lever is over Security Attachment
Screw. If screw interferes with assembly, check that screw is fully threaded into black lever catch.
4. Using screwdriver provided, rotate Security Attachment Screw counter-clockwise until flush with the
surface of the lever.
5. Secure lever with 6 lobe security screws. Screws should be flush when properly tightened.
6. Rotate key to horizontal and remove.
7. Assemble inside lever and secure with 6 lobe TORX® security screws.
Cylinder Removal
4
1. Remove the security screw on the outside of the lever with TORX® wrench.
2. Insert key and rotate key 45º clockwise. Keep key in this position.
3. Using screwdriver, tighten the Security Attachment Screw clockwise until it clears the lever.
4. Remove lever and remove key.
5. Remove cylinder from lever and install new cylinder.
6. Reinstall lever, following step 3 above.
11 Line w/ SL- Option
Installation Instructions
Bored Lock

1-800-727-5477 • www.sargentlock.com A7668B 3/20
Copyright © 2009, 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction
in whole or in part without the express written permission ofSARGENT Manufacturing Company is
prohibited.
4
SARGENT Manufacturing Company
100 Sargent Drive
New Haven, CT 06511 USA
800-727-5477
www.sargentlock.com
The ASSA ABLOY Group is the global leader in
access solutions. Every day, we help billions of
people experience a more open world.
ASSA ABLOY Opening Solutions leads the de-
velopment within door openings and prod-
ucts for access solutions in homes, businesses
and institutions. Our offering includes doors,
frames, door and window hardware, locks,
perimeter fencing, access control and service.