Dormakaba Confidant RFID User manual

Confidant RFID
Complete Lock with ASM Mortise /
Tubular Latch
Installation instructions
PK3621-T - 2019 - 02
EN

2 Confidant RFID ASM Mortise / Tubular Latch PK3621_T 02-19
Confidant RFIDTM Installation Instructions
IMPORTANT: Wear Safety glasses before starting the installation process.
Disclaimer ................................................................................ 3
1. Tools .................................................................................. 3
2. Inventory .............................................................................. 4
American Steel Mortise (ASM) .............................................................4
Tubular Latch ............................................................................5
3. Install Spindle .......................................................................... 6
4. Install Outside Lever .................................................................... 7
5A. Adjust Handing (Tubular latch lock with privacy only) .......................................8
5B. Prepare Inside Housing ..................................................................8
5C. Change Position of Stopper if Required (ASM and ADB)..................................... 9
5D. Apply privacy thumb turn sticker
(applicable only for multihousing locks or locks with automatic dead bolt) .................... 9
6. Install Lock on Door.................................................................... 10
American Steel Mortise (ASM / Tubular Latch) ..............................................10
7. Install Inside Trim Cover .................................................................11
8. Plug Battery Holder.....................................................................11
9. Test Lock Functionality..................................................................11
10. Program Lock - With Jack Cable..........................................................12
11. Install Battery Door ....................................................................12
Annex A 13
Installation of Standard ASM Mortise ...................................................... 13
Reversing the Mortise Handing ............................................................ 14
Annex B 17
Install Outside Housing with Gasket ....................................................... 17
Annex C 17
Remove Battery Holder ................................................................... 17
Annex D 18
Install Bluetooth and Messenger module.................................................... 18
Annex E 20
Remove cover of Bluetooth and Messenger module ..........................................20
Drilling Templates are in the center of the Installation Guide
Model: Confidant RFID
IC: 4652A-CRFID
FCCID: Q8SCONFIDANT-RFID
Regulatory Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications of this product, not approved by manufacturer will void the user’s authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Made in Canada ©2018 dormakaba. All trademarks and registered trademarks are the property of their respective owners.

Confidant RFID ASM Mortise / Tubular Latch PK3692_T 02-19 3
Disclaimer
1- Tools
ABC D
EF
A - Screw Driver Small Flat
B - Screw Driver Phillips #1 & #2
C - Screw Driver Torx T-20
D - Hexagonal Key 3 mm
E - 25mm / 24mm / 19mm / 12mm / 10mm Drill Bit
F - Needle Nose Pliers
CAUTION
WARNING
IMPORTANT
Please read and follow all directions carefully. Wear safety glasses when making the holes.
CAUTION
WARNING
IMPORTANT
Carefully inspect windows, doorframe, door, etc. to ensure that the recommended procedures will not
cause damage. Kaba Lodging Systems standard warranty does not cover damages caused by installation.
Respect applicable building codes regarding handle height.
Note: that the centerline of an ESM mortise does NOT pass through the screw holes on the strike.

4 Confidant RFID ASM Mortise / Tubular Latch PK3621_T 02-19
Inside Trim
with Thumbturn
Inside Trim
without Thumbturn
2- Inventory - American Steel Mortise (ASM)
Hardware Bag
ASM Mortise

Confidant RFID ASM Mortise / Tubular Latch PK3692_T 02-19 5
2- Inventory - Tubular latch
Hardware Bag
Tubular Latch
Inside Trim
with Thumbturn
Inside Trim
without Thumbturn

6 Confidant RFID ASM Mortise / Tubular Latch PK3621_T 02-19
3- Install Spindle
1- Check Handing:
Adjust for Right Hand (RH) or Left Hand (LH)
2- Insert Spindle.
3- Attach and Clamp Spindle Clip to Spindle as shown.
RH LH
Ensure legs are firmly clamped
against the spindle

Confidant RFID ASM Mortise / Tubular Latch PK3692_T 02-19 7
4- Install Outside Lever
Left Hand
1
1
2
2
Right Hand
Note: Hold down the outside lever against the outside housing while tightening the lever set screw.

8 Confidant RFID ASM Mortise / Tubular Latch PK3621_T 02-19
Handing RH to LH
5B- Prepare Inside Housing
5A- Adjust Handing (Tubular Latch lock with Privacy Only)
Inside Right Hand Housing
Handing LH to RH
Inside Left Hand Housing
1- Remove
1- Remove
2- Rotate 180˙
2- Rotate 180˙
3- Assemble
3- Assemble

Confidant RFID ASM Mortise / Tubular Latch PK3692_T 02-19 9
2
3
5
4
1
5C- Change The Position of Stopper
if Required (ASM and ADB)
5D- Apply Privacy Thumb Turn Sticker
(applicable only for multihousing locks or locks with automatic dead bolt)
LH
ASM ASM
RH
Automatic Dead Bolt VersionAmerican Steel Mortise Version
Back Plate Rear Back Plate Front
- To change the turn knob stopper from LH to RH, push stopper from FRONT (See 1)
- Assemble it in the REAR. Follow the arrows as shown
- Spring NOT required for Automatic Dead Bolt (ADB) versions
RH/RHR LH/LHR

10 Confidant RFID ASM Mortise / Tubular Latch PK3621_T 02-19
6- Install Lock on Door - ASM / Tubular Latch
Assemble spacers on screws
See Annex B for exterior applications
CAUTION
WARNING
IMPORTANT
After connecting all cables, make sure all excess cables are
pushed inside the hole(s) in the door.

Confidant RFID ASM Mortise / Tubular Latch PK3692_T 02-19 11
8- Plug Battery Holder
✗
✓
9- Test Lock Functionality
Make Sure Room Door is Open
A - Present Test Keycard
B - Check Green & Red Lights Flash
C - Rotate Outside Lever to Check Bolt Retraction
D - Release Outside Lever, Should Move Freely
E - Rotate Inside Lever to Check Bolt Retraction
F - Check Bolt Projection from Thumbturn
7- Install Inside Trim Cover
Thumbturn must
be vertical
(if applicable)
1
23

12 Confidant RFID ASM Mortise / Tubular Latch PK3621_T 02-19
11- Install Battery Door
A
C
B
D
10- Program Lock - With Jack Cable
CAUTION
WARNING
IMPORTANT
For security reasons, lock must be programmed BEFORE installing the battery door. Every time the bat-
tery door is removed pass an emergency card or connect lock to FDU/M-Unit to reset the tamper alarm.
Audit information is not affected.
CAUTION
WARNING
IMPORTANT

Confidant RFID ASM Mortise / Tubular Latch PK3692_T 02-19 13
1.1 Check the Mortise Handing
Compare the mortise with the diagram below.
CAUTION
WARNING
IMPORTANT
Refer to 1.2 to change the handing of a field-reversible mortise.
CAUTION
WARNING
IMPORTANT
When strike is installed on wood frames under one inch
thick, wood screws supplied are not adequate. use screws
of efficient lenght to engage the structural stud behind the
frame. Use only the strike and dust box supplied. Use of non-
approved parts may void the warranty.
CAUTION
WARNING
IMPORTANT
For Auto Deadbolt models
the gap between the mortise
front plate and the strike must
not exceed 1/4 “
Annex A- Installation of Standard ASM Mortise
Door Door Frame
Mortise
Max. 1/4"
For LH (left hand) and
RHR (right hand reverse)
For RH (right hand) and
LHR (left hand reverse)
ASM Door Handing (Top View)
Right Hand (RH)
Left Hand (LH)
Right Hand Reverse (RHR)
Left Hand Reverse (LHR)

14 Confidant RFID ASM Mortise / Tubular Latch PK3621_T 02-19
Annex A • Reversing the Mortise Handing
1.2 Reversible ASM
1. Remove the mortise faceplate. Remove screw (V) and
lock washer (W) if applicable and place the mortise on a
flat surface for the following steps.
W
V
Only apply to mortise no
deadbolt, auto-deadbolt
and armed automatic
deadbolt (if applicable)
2. Partially extend the deadbolt:
For normal ASM, rotate hub (H) using a screwdriver, until
the deadbolt (D) extends approximately 1/4".
D
1/4"
H
Proceed to step 3.
For Autodeadbolt ASM, rotate hub (H) until the deadbolt
(D) is fully retracted. The deadbolt will extend approx.
1/16" from the mortise case.
D
1/16"
H
Hold deadbolt (D) gently. Press and release the auxiliary
latch (X). You should feel the deadbolt trigger and begin
to extend under the force of the spring.
D (hold gently)
X (press and release)
Release the deadbolt (D) gently. It should extend to 5/16"
approx. and stop. If the deadbolt extends past this point,
gently press it in until it locks at 5/16" throw, or start step
2 again.
D
5/16"

Confidant RFID ASM Mortise / Tubular Latch PK3692_T 02-19 15
Annex A • Reversing the Mortise Handing
Reversing Handing ASM
3. Push in the latch bolt (L) to the middle of its stroke, and
hold it there. ( Continue Step 1 and 2)
12
Use a small screwdriver
to lift unlock mechanism.
Unlock Position
Lock Position
Push in the latchbolt to
the end of the stroke,
and hold it there.
LL
Hold the latch (L) inside the mortise, and insert the tail-
piece retaining tool (S, part #027-510382 available sep-
arately) so that the tailpiece (T) will not drop inside the
mortise case. Hold the tool and the latch with one hand,
and slide up the tailpiece using a small screwdriver.
L
T
S
(part #027-510382)
Continue to hold tool (S). Release the latch bolt (L) and
keep the anti-friction latch (F) toward the flat side of the
latch bolt so that the bolt extends fully.
L
F
S
4. Pull out the latch bolt (L), until it just clears the front
plate. (Note: If you remove the bolt completely, you
must turn it 90° to re-insert it.)
L
180°
Rotate the latch bolt (L) 180°. Re-insert it to the end of
its stroke.
L
Holding tool (S) in place, re-engage tailpiece (T) with latch
bolt (L) (slide tailpiece down). There may be some play re-
quired to align the parts. Remove the tool (S).
L
T
S
Release the latch to the middle of the stroke and hold it
there. Use a small screwdriver to push the lock mechanism
back on lock position (see step 1 and 2) .
CAUTION
WARNING
IMPORTANT
The lock mechanism has to be horizontal on lock position

16 Confidant RFID ASM Mortise / Tubular Latch PK3621_T 02-19
Annex A • Reversing the Mortise Handing
5. Release the latch bolt (L). Position the latch bolt so that
the bottom tooth of the anti-friction latch (F) remains
inside the mortise case as shown.
CAUTION
WARNING
IMPORTANT
If the tooth of (F) is outside the mortise, you will not be
able to re-assemble the faceplate on the mortise.
L
FL
F (tooth)
mortise
bottom view
6. If the auxiliary latch (X) is shaped like a triangle, there is
no need to change its handing.
X (triangular = OK)
If the auxiliary latch (X) is a crescent shape, remove it,
turn it 180°, and replace it. The auxiliary latch slides easily
in and out of the mortise.
X (crescent = must be reversed)
180°
(re-insert)
7. Assemble back screw (V) and lock washer (W) if appli-
cable. The screw (V) must be tightened.
CAUTION
WARNING
IMPORTANT
Screw (V) must not touch the back wall of mortise cut-
out on the door
8. The mortise should look like the diagram below. (Check
the orientation of the latch bolt and auxiliary latch.)
Check the bevel of the mortise and change it if required
as described in section 3.3, paragraph 6 page 10.
For LH (left hand)
and RHR (right hand
reverse)
For RH (right hand)
and LHR (left hand
reverse)
W
V
W
V
ASM
Only apply to mortise no deadbolt,
auto-deadbolt and armed automatic deadbolt

Confidant RFID ASM Mortise / Tubular Latch PK3692_T 02-19 17
Annex B- Install Outside Housing with Gasket
(Exterior and Ocean Front Versions)
Annex C • Remove Battery Holder
A
C
B
D
Unscrew
Unclip Battery Holder
Remove Door
Remove Battery Holder

18 Confidant RFID ASM Mortise / Tubular Latch PK3621_T 02-19
13-A 3-B2
5
4
Annex D- Install Bluetooth and Messenger
module
Battery must be disconnected before adding Bluetooth and Messenger module.
See Annex E for instructions of how to remove the cover from the module.

Confidant RFID ASM Mortise / Tubular Latch PK3692_T 02-19 19
Annex D- Install Bluetooth and Messenger
module
MESSENGER-A
MESSENGER-B
12 3
456
How to change orientation of Messenger antenna board. The lock is provided with orien-
tation of board for Messenger hub outside the room.
Orientation when Messenger
hub outside the room
Orientation when Messenger
hub inside the room
Position of Bluetooth
antenna board

20 Confidant RFID ASM Mortise / Tubular Latch PK3621_T 02-19
SEE
DETAIL X
DETAIL X
SCALE 1:1
Annex E • Remove cover of Bluetooth and
Messenger module