Dormakaba ED50 User manual

ED50/ED100/ED250
Swing Door Operators
Installation in Overhead Concealed Header
Owner's Manual
DL4616-011 – 09-2021
| EN |

2ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Table of Contents
Table of contents 
 General information 
 To our customers 
 What you should know 
. Distributor information 
. ED low energy operator 
. ED/ED operator power
configuration 
. Low energy power operated swinging doors
ANSI/BHMA A. 
. Power operated swinging doors
ANSI/BHMA A. 
. Mode switch panel 
 AAADM safety information labels 
. Safety information label, full energy swing
doors (ANSI/BHMA A.) 
. Safety information label, low energy swing
doors (ANSI/BHMA A.) 
 Daily safety check procedure 
. Full energy power operated swing door
(ANSI/BHMA .) 
. Low energy power operated swing door
(ANSI/BHMA .) 
 General safety related items 
. Full energy power operated swing door
(ANSI/BHMA .) 
. Low energy power operated swing door
(ANSI/BHMA .) 
Table of contents
 ED/ED/ED door signage 
. ED/ED operator configured for full
energy 
. ED operator and ED/ED
operator configured for low energy 
. Door signage, full energy power operated
single swing doors (ANSI/BHMA .) 
. Door signage, low energy power operated
single swing doors (ANSI /BHMA .):
initiation of door operation 
. Door signage, full energy power operated
double swing doors (ANSI/BHMA .) 
. Door signage, low energy power operated
double swing doors, initiation of door
operation (ANSI/BHMA .) 
. Door signage, full energy power operated
double egress swing doors
(ANSI/BHMA .) 
 ED//ED header
maintenance 
. ED/ED/ED environment and
cleaning 
. Operator status LEDs 

3
ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 1
. ED/ED/ED OHC header Installation.
NOTICE
Exterior door use.
To insure proper suitability for exterior door
use, the following topics must be addressed in
the context of the door application setting.
• Site-specific use factors such as high wind
conditions and/or building pressure.
• Door width, height, weight, and usage
patterns.
• Observable prevailing conditions at the
opening under which the operator is
expected to perform. In some instances, this
may require increased force settings to
counteract these conditions.
• Door mounted presence sensors.
When attempting to overcome these forces,
it is strongly suggested that door mounted
presence sensors be employed to enhance
pedestrian safety through the opening.
 General information
Fig.1.1 Single door OHC header with overhead arm
. Manual storage.
This document must be kept in a secure place, and
accessible for reference as required.
If the door system should be transferred to another
facility, insure that this document is transferred as well.
. dormakaba.us website.
Manuals are available for review, download, and printing
on dormakaba.us website.
. Dimensions
Unless otherwise specified, all dimensions are given in
inches (“).
. Symbols used in this manual.
WARNING
This symbol warns of hazards which could result
in personal injury or threat to health.
NOTICE
Draws attention to important information
presented in this document.
. Owner's manual.
This Owner's manual applies to dormakaba
ED/ED/ED swing door operators packaged
in an overhead concealed header (OHC).
Fig. 1.2 ED50 low energy OHC operator
Fig.1.3 ED100/ED250 OHC operator

4ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 2
 To our customers
We are pleased that a dormakaba
ED/ED/ED overhead concealed header (OHC)
assembly has been selected for this swing door
installation. dormakaba USA Inc. designed, tested and
built this assembly to provide many years of service.
The purpose of this manual is to familiarize you with
your ED/ED/ED overhead concealed header
installed on a swing door.
It is essential that you "know your system" and that you
recognize the importance of maintaining your door
system in compliance with industry standards for safety.
It is your responsibility as owner and caretaker of the
equipment, to inspect the operation of your door system
on a daily basis as outlined in Chapter , Daily Safety
Check Procedure to insure that it is safe for use by your
customers and employees.
WARNING
Should the door fail to operate as prescribed
in the Safety Information Checklist or at any
other time for any reason, do not attempt to
repair or adjust the ED/ED/ED
overhead concealed swing door system!
Call your local authorized dormakaba USA Inc.
distributor for repair.
The distributor's AAADM certified technicians are
trained to install and service the ED/ED/ED
overhead concealed swing door system using the
dormakaba USA, Inc. Installation and Setup Manuals
and in accordance with ANSI/BHMA safety standards.
. Service availability.
dormakaba USA Inc. has a nationwide network of
authorized distributors for sales, installation and service
of its products.
. Compliance with industry standards for safety.
Your ED/ED/ED overhead concealed swing
door system was designed to the latest ANSI/BHMA
operating and safety standards. In order to insure the
continued safe operation of the door, it is important
that:
• Proper decals and labels be applied and maintained
on your doors (Chapter ).
• If decals and labels have been removed, or cannot be
read, contact your local authorized dormakaba USA
Inc. distributor for replacement decals or labels.

5
ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 3
 What you should know
.. dormakaba USA Inc. distributor information.
Be sure that the dormakaba USA Inc. distributor has
provided the following information for each door
installation:
. dormakaba USA Inc. ED/ED/ED Overhead
Concealed Owner's Manual DL-.
. Review of:
• Daily Safety Check Procedure (Chapter ).
• General Safety Related Items (Chapter ).
. Instructions on how to conduct the daily safety check
procedure by walk through example.
. Annual compliance inspection label completion
(Chapter ).
. Circuit breaker or disconnect location for  Vac
power to the ED/ED/ED overhead
concealed header.
. ED/ED/ED Mode switch panel location
and instructions in its use (Para. .).
. Discussion of problems that could result from
ED operator being allowed to operate after a
malfunction observed.
. Number to call for service or questions about your
system if you are uncertain of any condition or situation.
WARNING
If there are any problems, discontinue door
operation immediately and secure the door in
a safe manner.
Call your local dormakaba USA Inc. distributor
for repair.
. Distributor information
.. Knowing act definition (ANSI/BHMA A.).
Any conscious action with the expected result of opening
a door. This includes but is not limited to:
• Wall or jamb mounted contact or non contact
switches such as pushplates.
• The action of of manually opening (pushing or
pulling) a door.
• Controlled access devices such as keypads, card
readers, wireless transmitters and key switches.
. Low energy power operated
swinging doors
ANSI/BHMA A.
.. Low energy power operator door definition
(ANSI/BHMAA.).
A door with a power mechanism that opens the door
upon receipt of a knowing act signal, does not generate
more kinetic energy than specified in the ANSI/BHMA
A. standard, and is closed by a power mechanism
or other means.
. Power operated swinging doors
ANSI/BHMA A.
.. Power operated door definition
(ANSI/BHMA A.).
The combination of door, operator, controls and sensors
constituting the system. (also called automatic door.).
. ED/ED operators can be configured for:
• Low energy (Para. .).
• Power operated (full energy) (Para. .).
. ED/ED operator power
configuration
. ED low energy operator
ED operator is available only as a low energy operator
(Para. .).

6ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 3
. Mode switch and Exit Only switch panel
.. Mode switch position descriptions.
Auto
. Door opens automatically when one of the activators
is actuated or triggered.
Door closes on expiration of adjustable hold open
time with no activators or actuators triggered.
. With knowing act device actuation (Para. ..).
Door will remain at full open position for not less
than  seconds.
. With push/pull actuation of door (Para. .).
Door will remain at full open position for not less than
 seconds.
Close
. Door will remain closed, or if door is open door will
close.
Open
. Door opens automatically and remains open.
.. Exit Only switch position descriptions.
On
. Exterior activation sensor or knowing act device
disabled when door fully closed.
• Only interior activation sensor or knowing act device
will enable door opening.
Off
. Both interior and exterior activation sensors or
knowing act devices will enable door opening.
.. Exit Only switch
positions.
1Mode switch panel
2Mode switch,
three position
1
2
4
3
Auto
Fig. 3.6.2 Auto
.. Mode switch
positions.
Close
Fig. 3.6.3 Close
Fig. 3.6.4 Open
Fig. 3.6.5 On
On
Off
Fig. 3.6.6 Off
Open
Fig. 3.6.1 Mode switch and Exit Only switch panel
3Exit only switch,
two position
4RJ45 Comm port for
service
Fig. 3.6.7 Optional key switch panels

7
ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 4
.. Full energy automatic swing door safety
information label.
This AAADM label (Fig. ..) outlines safety checks that
should be performed daily on a swing door controlled by
an ED/ED OHC operator configured for full
energy operation (ANSI/BHMA .).
.. Safety information label location.
Place label in a protected, visible location on door frame,
near program switch panel if possible.
.. Annual compliance section of label.
This section of label is only completed on automatic
swing doors that comply with ANSI/BHMA A.
standard and pass inspection by an AAADM certified
dormakaba USA Inc. technician.
.. Additional annual compliance inspection labels.
Place additional labels (Fig. ..) over annual
compliance inspection section of safety information
label.
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.10 ON:
DATE: _____________
by AAADM Certified
Inspector
Number: ____________
Fig. 4.1.2 Annual
compliance
label, full
energy
SAFETY INFORMATION
Automatic Swinging Doors
1
. Walk toward the door at a
normal pace. The door
should open when you ar
e
about 4 feet from the door.
2
. Stand motionless on
threshold for at least 10
seconds. The door shoul
d
not close.
3
. Move clear of the area. Th
e
door should remain open for
at least 1.5 seconds and
should close slowly and
smoothly.
4
. Repeat steps1 through 3
from other direction if door
is used for two way traffic.
5
. Inspect the floor area. It
should be clean with no
loose parts that might caus
e
user to trip or fall. Keep
traffic path clear.
6
. Inspect door's overall
condition. The appropriat
e
signage should be present.
7
. Have door inspected by a
n
AAADM certified inspecto
r
at least annually.
AAADM
American Association of Automatic
Door Manufacturers
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.10 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-2496
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power
.
Fig. 4.1.1 Full energy safety
information label
. Safety information label, full energy swing doors (ANSI/BHMA A.)
 AAADM safety information labels

8ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 4
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
should open at a slow
smooth pace (4 or more
seconds), and stop withou
t
impact.
2
. Door must remain fully open
for a minimum of 5 seconds
before beginning to close.
3
. Door should close at a slow,
smooth pace (4 or more
seconds), and stop without
impact.
4
. Inspect the floor area. It
should be clean with no
loose parts that might cause
user to trip or fall. Keep
traffic path clear.
5
. Inspect door‘s overall
condition. The appropriate
signage should be present
and the hardware should
be in good condition.
6
. Have door inspected by an
AAADM certified inspector
at least annually.
AAADM
American Association of Automatic
Door Manufacturers
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
Fig. 4.2.1 Low energy safety
information label
. Safety information label, low energy swing doors (ANSI/BHMA A.)
.. Low energy swing door safety information label.
This AAADM label (Fig. ..) outlines safety checks that
should be performed daily on a swing door controlled by
an:
• ED OHC operator.
• ED/ED OHC operator configured for low
energy operation (ANSI/BHMA A.).
.. Safety information label location.
Place label in a protected, visible location on door frame,
near operator power switch if possible.
.. Annual compliance section of label.
This section of label is only completed on low energy
swing doors that comply with ANSI/BHMA A.
standard and pass inspection by a AAADM certified
dormakaba USA Inc. technician.
.. Additional annual compliance inspection labels.
Place additional labels (Fig. ..) over annual
compliance inspection section of safety information
label.
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE: ______________
by AAADM Certified
Inspector
Number: ___________
Fig. 4.2.2 Annual
compliance
inspection
label

9
ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 5
 Daily safety check procedure
NOTICE
All figures and diagrams are for purposes of
illustration only and are from AAADM power
operated pedestrian door manual, reprinted
with permission.
.. Performing daily safety checks.
Perform safety checks daily on your automatic swinging
door to insure your customer and employee safety.
The daily safety checks are listed in Chapter , AAADM
safety information labels.
TIPS AND RECOMMENDATIONS
Perform these checks while traffic is restricted
from all detection and sensing zones.
.. Sensor activation, safety sensor detection.
. Check activation sensor by walking toward door
opening at moderate speed, door should:
• Start opening when you are about four feet from
door.
• Open smoothly.
• Stop at fully open without impact.
. Move slowly through door opening (approximately six
inches/second) stop in door swing path, and pause
for ten seconds.
• Door should remain open.
. If two way traffic, repeat from other side of door.
. Step out of sensor zone activating area.
• After a brief delay (minimum . seconds) door
should close smoothly and without impact.
. For one way traffic, approach safety side of door and
have someone else approach activating side.
• Door equipped with overhead mounted safety sensor
(Fig ..), as long as you are in safety area of door it
should not open.
• Door equipped with door mounted safety sensors
(Fig .., Fig. ..), door may start to open but
should reverse, stop or slow down.
. Stand motionless in door for at least  seconds.
• Door equipped with overhead mounted presence
sensor (Fig ..), door should not close.
• Door equipped with door mounted safety sensors
(Fig .., Fig. ..), door may start to close but
should reverse, stop or slow down.
Fig. 5.1.1 One way traffic, overhead mounted safety
sensor
Fig. 5.1.2 One way traffic, door mounted safety sensors
. Full energy power operated swing door (ANSI/BHMA .)
Minimum
activating
detection
zone
Guide rail Guide rail
Safety
detection zone
43”
[1092 mm]
Clear door
opening
Minimum
activating
detection
zone
Guide rail Guide rail
Safety beam
Safety zone
Safety zone

10 ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 5
Fig. 5.1.3 Two way traffic, activating and safety
detection zones with door mounted safety
sensors
Safety zone
Safety zone
Minimum
activating
detection
zone
43”
[1092 mm]
Edge of open door
plus 55” [1397 mm]
minimum guide rail
and activation
Minimum
activating
detection
zone
.. Swing door double egress; knowing act switch
activation.
. Double egress doors are commonly activated by
knowing act switch(es).
. Operate knowing act device, doors should:
• Open smoothly and stop at fully open without
impact.
• Remain open for a minimum of five seconds before
closing.
. As door closes, approach door from approach side:
• Door should reopen.
. Continue across threshold and stand motionless for
 seconds:
• Door should not contact you.
Safety zone
Safety zone
Safety zone
Safety zone
Pivot
Pivot
Push plate
Push plate
Fig. 5.1.5 Door mounted safety sensors
Fig. 5.1.4 Overhead safety sensors
Secondary
activation
zone
Secondary
activation
zone
Safety
zone
Safety
zone
Push plate
Push plate
. Continue through door, the door should:
• Start closing after a minimum of five seconds.
• Close smoothly and without impact.
. Approach safety zone side of door:
• If door equipped with overhead safety sensor
(Fig. ..) door should not open as long as you are in
safety zone when door closed.
• If door equipped with door mounted safety sensor
(Fig. ..) door may start to open but should
reverse, stop or slow down.

11
ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 5
. Low energy power operated swing door (ANSI/BHMA .)
.. Performing daily safety checks.
Perform safety checks daily on your low energy swing
door to insure your customer and employee safety.
These daily safety checks are also listed in Chapter ,
Safety Information labels, low energy swinging doors.
. Activate the door by a knowing act (Para..).
• Door should open at a slow smooth pace
( seconds or more) and stop without impact.
. Door must remain fully open for a minimum of
 seconds before beginning to close.
• Door should close at a slow smooth pace
( seconds or more) and stop without impact.
. Inspect the floor area, it should be kept clean with no
loose parts that might cause user to trip or fall. Keep
traffic path clear.
. Inspect door's overall condition. The appropriate
signage (Chapter ) should be present and all
hardware should be in good condition.
. Have door inspected by a dormakaba USA Inc.
AAADM certified technician at least annually.
WARNING
If there are any problems, discontinue door
operation immediately and secure the door in
a safe manner.
Call your local dormakaba USA Inc. distributor
for repair.

12 ED50/ED100/ED250 09-2021DL4615-013
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 6
 General safety related items
.. Review safety related items and perform checks
periodically as noted.
TIPS AND RECOMMENDATIONS
Perform these checks while traffic is restricted
from all detection and sensing zones.
. Housekeeping:
• Check door area for tripping or slipping hazards.
• Check all doors for damage.
• Make sure all hardware and overhead covers are
properly secured.
• There should be no bulletin boards, literature racks,
merchandise displays, or other attractions in the
door area that would interfere with the use of the
door or encourage people to stop and stand in the
door area.
. Door closing force:
• Force to prevent the door from closing should not
exceed  pounds measured with a force gauge.
. Door safety signage:
• Refer to Chapter  for door safety signage
requirements.
• Refer to Chapter  for Safety Information labels.
. Activating switch, knowing act (Para. .):
• Doors equipped with a manual activating switch
shall hold door fully open for a minimum of five
seconds before closing.
. Guide rails (Fig. .., Fig. ..), if used:
• Check that guide rails or other barriers or separators
are present (two per swing door side) and firmly
anchored.
• Rail lengths should be the width of the open door or
greater.
Fig. 6.1.1 Guide rails, jamb and floor mounted Fig. 6.1.2 Guide rails, free standing, floor mounted
. Full energy power operated swing door (ANSI/BHMA .)
Width of door
minimum
Door jamb
30” [762 mm]
minimum
“6” [152 mm]
maximum
Divider
Door jamb
Width of door
minimum
Panel
30” [762 mm]
minimum
. Lock stile:
• With door open, grasp lock stile of door and attempt
to move horizontally and vertically.
• There should be no looseness in the door pivots or in
connections between door and operator.
. Breakout stop:
• Center pivoted in swinging doors may be supplied
with an emergency breakout stop or switch that will
allow the door to open in the direction of emergency
egress.
• When the door is pushed into the breakout mode,
check that the door will not activate.
. Traffic patterns:
• Observe traffic patterns. Plan routing so people
enter and exit in a straight approach, directly toward
the door opening.
. Finger guard:
• If installed, inspect finger guard to see that it is
secure and in good repair.
. AAADM safety information label (Chapter ):
• An AAADM safety information label should be
affixed on the door or door frame in a protected,
visible location.
• If you need additional decals or labels, contact your
local authorized dormakaba USA Inc. distributor.
WARNING
If there are any problems, discontinue door
operation immediately and secure the door in
a safe manner.
Call your local dormakaba USA Inc. distributor
for repair.

13
ED50/ED100/ED250 09-2021DL4615-013
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 6
. Low energy power operated swing door (ANSI/BHMA .)
.. Review safety related items and perform checks
periodically as noted.
TIPS AND RECOMMENDATIONS
Perform these checks while traffic is restricted.
. Housekeeping:
• Check door area for tripping or slipping hazards.
• Make sure all hardware and overhead covers are
properly secured.
• There should be no bulletin boards, literature racks,
merchandise displays, or other attractions in the
door area that would interfere with the use of the
door or encourage people to stop and stand in the
door area.
. Check all doors for damage.
. Door closing force:
• Force to prevent the door from closing should not
exceed  pounds measured with a force gauge.
. Door safety signage:
• Refer to Chapter  for door safety signage
requirements. Chapter  documents safety
information (daily safety check) and annual
compliance inspection labels requirements.
. Lock stile:
• With door open, grasp lock stile of door and attempt
to move horizontally and vertically.
• There should be no looseness in the door pivots or in
connections between door and operator.
. Breakout stop:
• Center pivoted in swinging doors may be supplied
with an emergency breakout stop or switch that will
allow the door to open in the direction of emergency
egress.
• When the door is pushed into the breakout mode,
check that the door will not activate.
WARNING
If there are any problems, discontinue door
operation immediately and secure the door in
a safe manner.
Call your local dormakaba USA Inc. distributor
for repair.

14 ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 7
 ED/ED/ED door signage
Signage and warnings are specified in
ANSI /BHMA A., American National Standard for
Power Operated Pedestrian Doors, paragraph .
.. Door, one way traffic, Fig. ...
. Arrow and AUTOMATIC DOOR, one side of decal.
• Shall be visible from approach side of a swinging door,
mounted on door at a height of " ± " from floor to
centerline of sign.
. DO NOT ENTER and AUTOMATIC DOOR, one side of
decal (or separate decal for solid doors - DD-).
• Shall be visible from non-approach side of door that
swings towards pedestrians attempting to travel in
wrong direction.
.. Door, two way traffic, Fig. ...
. Arrow and AUTOMATIC DOOR, one side of decal.
• Shall be visible from approach side of a swinging door,
mounted on door at a height of " ± " from floor to
centerline of sign.
. CAUTION AUTOMATIC DOOR, one side of decal.
• Swinging doors serving both egress and ingress shall
have a "CAUTION AUTOMATIC DOOR" sign visible
from swing side of door.
• Sign shall be mounted on door at a height of  ± "
from floor to centerline of sign.
.. Overview Fig. 7.1.1 One decal, approach side, non-approach side
. ED/ED operator configured for full energy
Fig. 7.1.2 One decal, two way traffic
Fig. 7.1.3 ACTIVATE SWITCH TO OPERATE decal
DD-
DD-
DD-
AUTOMATIC
DOOR
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
AUTOMATIC
DOOR
DD0739-010
AUTOMATIC
DOOR
DO NOT
ENTER
CAUTION
DOOR
AUTOMATIC
DD0756-010
dormakaba
. ED operator and ED/ED operator configured for low energy
.. Overview
Signage and warnings are specified in
ANSI /BHMA A., American National Standard for
Power Assist and Low Energy Power Operated Doors.
.. All low energy doors.
. AUTOMATIC CAUTION DOOR decal.
• All low energy doors shall be marked with signage
visible from both side of door with the words
"AUTOMATIC CAUTION DOOR".
• Signs shall be mounted " ± " from floor to
centerline of sign.
.. Knowing act switch used to initiate door operation.
. ACTIVATE SWITCH TO OPERATE decal.
• When a knowing act device is used to initiate operation
of door operator, door shall be provided with sign on
each side of door where switch is operated with
message "ACTIVATE SWITCH TO OPERATE".
.. Push/Pull used to initiate door operation.
. PUSH TO OPERATE, PULL TO OPERATE decals.
• When push/pull is used to initiate operation of door
operator, doors shall be provided with the message
"PUSH TO OPERATE" on push side of door and
"PULL TO OPERATE" on pull side of door.
.. Knowing act door.
. ACTIVATE SWITCH TO OPERATE decal.
• Knowing act doors shall have signage stating
"ACTIVATE SWITCH TO OPERATE" on side of door
having knowing act switch or other knowing act device.
Fig. 7.2.1 AUTOMATIC CAUTION DOOR decal
Fig. 7.2.2 ACTIVATE SWITCH TO OPERATE decal
Fig. 7.2.3 PUSH TO OPERATE, PULL TO OPERATE decals
DD-
DD- DD-
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD-
1Activate Switch to
Operate DD0758-010
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010 1
2Push to Operate
DD0762-010
3Pull to Operate
DD0762-020
DD0762-010
PUSH
TO OPERATE 2
DD0762-020
PULL
TO OPERATE 3

15
ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 7
. Door signage, full energy power operated single swing doors
(ANSI/BHMA .)
Fig. 7.3.1 One decal, one way traffic
Approach side Swing side
Fig. 7.3.3 One decal, two way traffic
. Door signage, low energy power operated single swing doors
(ANSI /BHMA .): initiation of door operation
Fig. 7.4.1 Knowing act device
Fig. 7.3.2 One way traffic
Approach side Swing side
Fig. 7.3.4 Two way traffic
Approach side
Swing side
Approach side
Swing side
Fig. 7.4.2 Push/Pull
Push To Operate Pull To Operate
50” ± 12”
AUTOMATIC
DOOR
DD0739-010
AUTOMATIC
DOOR
DO NOT
ENTER
50” ± 12”
AUTOMATIC
DOOR
CAUTION
DOOR
AUTOMATIC
DD0756-010
dormakaba
50” ± 12”
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
50” ± 12”
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
DD0762-020
PULL
TO OPERATE
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-010
PUSH
TO OPERATE
DD0762-010
PUSH
TO OPERATE

16 ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 7
. Door signage, full energy power operated double swing doors
(ANSI/BHMA .)
Fig. 7.5.1 One way traffic, approach side Fig. 7.5.4 One way traffic, swing side
Fig. 7.5.6 Knowing act, swing side, one way
Fig. 7.5.2 Two way traffic, approach side
Fig. 7.5.3 Knowing act, approach side, one way
50” ± 12”
AUTOMATIC
DOOR
AUTOMATIC
DOOR
50” ± 12”
AUTOMATIC
DOOR
AUTOMATIC
DOOR
50” ± 12”
DD0739-010
AUTOMATIC
DOOR
DO NOT
ENTER
DD0739-010
AUTOMATIC
DOOR
DO NOT
ENTER
50” ± 12”
DD0739-010
AUTOMATIC
DOOR
DO NOT
ENTER
DD0739-010
AUTOMATIC
DOOR
DO NOT
ENTER
50” ± 12”
AUTOMATIC
DOOR
AUTOMATIC
DOOR
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
Fig. 9.5.5 Two way traffic, swing side
50” ± 12”
CAUTION
DOOR
AUTOMATIC
DD0756-010
dormakaba
CAUTION
DOOR
AUTOMATIC
DD0756-010
dormakaba

17
ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 7
. Door signage, low energy power operated double swing doors,
initiation of door operation (ANSI/BHMA .)
Fig. 7.6.1 Knowing act device, approach side Fig. 7.6.3 Knowing act device, swing side
Fig. 7.6.4 Push/Pull, Pull
Fig. 7.6.2 Push/Pull, Push
50” ± 12”
CAUTION
DOOR
AUTOMATIC
DD0586-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
50” ± 12”
CAUTION
DOOR
AUTOMATIC
DD0586-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
DD0758-010
ACTIVATE SWITC H
TO OPERATE
DD0758-010
50” ± 12”
CAUTION
DOOR
AUTOMATIC
DD0586-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-010
PUSH
TO OPERATE
DD0762-010
PUSH
TO OPERATE
DD0762-010
PUSH
TO OPERATE
DD0762-010
PUSH
TO OPERATE
50” ± 12”
CAUTION
DOOR
AUTOMATIC
DD0586-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
DD0762-020
PULL
TO OPERATE
DD0762-020
PULL
TO OPERATE
DD0762-020
PULL
TO OPERATE

18 ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 7
. Door signage, full energy power operated double egress swing doors
(ANSI/BHMA .)
Fig. 7.7.2 RH double egress, interior side
Swing side Approach side
Fig. 7.7.3 RH double egress, exterior side
Swing side Approach side
Fig. 7.7.6 LH double egress, exterior side
Fig. 7.7.5 LH double egress, interior side
Fig. 7.7.1 OHC RH double egress Fig. 7.7.4 OHC LH double egress
Swing sideApproach side
Swing sideApproach side
50” ± 12”
DD0739-010
AUTOMATIC
DOOR
DO NOT
ENTER
AUTOMATIC
DOOR
50” ± 12”
DD0739-010
AUTOMATIC
DOOR
DO NOT
ENTER
AUTOMATIC
DOOR
50” ± 12”
DD0739-010
AUTOMATIC
DOOR
DO NOT
ENTER
AUTOMATIC
DOOR
50” ± 12”
DD0739-010
AUTOMATIC
DOOR
DO NOT
ENTER
AUTOMATIC
DOOR
Swing side Approach side Swing side
Approach side

19
ED50/ED100/ED250 09-2021DL4616-011
dormakaba ED50/ED100/ED250 Owner's Manual
Overhead concealed header
Chapter 8
 ED//ED header maintenance
. ED/ED/ED environment and cleaning
.. ED/ED/ED environmental
requirements.
ED/ED/ED overhead concealed header
assembly is designed to operate under the
environmental specifications shown in Table ...
.. Areas around door(s) and door swing radius.
Areas around doors and door swing radius must be kept
clear of all obstacles.
.. Cleaning of header.
WARNING
Cleaning of all header surfaces must be done
with Mode switch (Para. 3.5) in CLOSE position!
External surfaces of the header can be cleaned with a
damp cloth and commercial cleaning agents.
TIPS AND RECOMMENDATIONS
Abrasive (scouring) agents should not be used
as they may damage external surfaces.
.. Water and other liquids.
CAUTION
No water or other liquids must be sprayed or
spilled on ED50/ED100/ED250 overhead
concealed header!
Table 8.3.1 Operator environmental requirements
Fig. 8.3.1 ED50/ED100/ED250 overhead concealed
header
Ambient temperature  to  °F
. Operator status LEDs
Fig. 8.2.1 Operator status LEDs, header cover removed .. Operator status LEDs.
. Red LED
Blinking codes are used to indicate "ln__" information
(system status or operating conditions) or certain
error codes "E__".
. Yellow LED
Maintenance interval indicator. When illuminated, an
indication the operator system has to be serviced.
. Green LED
• On, internal  Vdc power is On.
• Off, internal  Vdc power is Off.
TIPS AND RECOMMENDATIONS
Details on LED status codes and maintenance
intervals can be found in Appendix B –
Troubleshooting.
1Red LED
2Yellow LED
3Green LED
1
2
3
45
6
4Accessory terminal
board
5OHC header
6Power Off/On switch

www.dormakaba.us
dormakaba USA Inc.
1 Dorma Drive, Drawer AC
Reamstown, PA 17567
USA
T: 717-336-3881
F: 717-336-2106