Dormakaba ED50LE User manual

ED50LE
Low energy swing door operator
Installation Instructions
DL4616-002 – 09-2021
| EN |

2ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Table of Contents
Table of contents 
 General information 
. General information 
. Single door configuration examples 
. Double door configuration examples 
 Product overview 
. EDLE low energy operator 
. EDLE/EDLE companion door full
width cover kits 
. Fine cover kit hardware 
. Pull, push arm kits 
. Arm screw kits 
. Optional key switch panels 
. EDLE axle extensions 
. Push arm door stop - option 
. Double door EDLE operator connection
cables 
 Technical data 
. EDLE operator technical data 
. EDLE operating specifications 
 EDLE terminal board interfaces 
. EDLE terminal board interfaces 
 EDLE door signage 
. Low energy operator 
. Door signage, low energy swing door per
ANSI / BHMA A. 
. Safety label, low energy swing doors 
 Recommended tools and torque chart 
. Recommended tools 
. Standard tightening torque 
. Drill bits 
 EDLE operator installation templates 
. EDLE installation templates 
 EDLE operator installation 
. Installation preparation 
. Remove mounting plate from EDLE
operator 
. Customer  Vac connection to
mounting plate terminal block 
. Mounting plate attachment to jamb or
wall 
. Connect customer  Vac to mounting
plate terminal block 
. Route accessory wiring to mounting plate 
. Remove protective film strips from
operator 
. Install EDLE operator onto mounting
plate 
Table of contents
 Push arm installation 
. Push arm installation templates 
. Push arm installation 
 Pull arm installation 
. Pull arm installation 
. Pull arm assemblies 
. Pull arm hardware 
. Install hardware into track 
. Assemble slide shoe 
.6 Assemble drive arm and CPD lever 
. Fasten drive arm to EDLE operator 
. Install track assembly 
 EDLE Operator spring tension 
. Set operator spring tension 
 ANSI/BHMA standards 
. ANSI/BHMA A. Low Energy Power
Operated Swinging Doors 
 Install door signage, low energy
door 
. Install door signage 
 Cover, end caps and spindle caps 
. Cover end cap and spindle installation 
 Maintenance 
. Safety label, low energy swing doors 
. Arm fasteners – torque requirements 
. EDLE brake maintenance 
Appendix A - Fine cover professional cover kits 
A. Professional cover kit HK-X
installation instructions – single door 
A.. Professional cover kit HK-X
installation instructions – pair 
Appendix B - Key switch wiring diagrams 
B. DX-C Key Switch Panel with RJ
connector 
B. DX-C Key Switch Panel 
Appendix C - Knowing act switch wiring 
diagram 
C. Knowing act switches 
C. Knowing act switch wiring diagram 

3
ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 1
.. EDLE installation.
NOTICE
Installation on an interior building surface.
The EDLE with fine cover must be installed
on an interior building surface.
.. Installation Instructions.
This manual provides installation instructions for the
following EDLE door configurations.
Reference Para. . for illustrations.
Single doors.
. RH and LH pull.
. RH and LH push.
Double doors.
. Pull
. Push
. Double egress
 General information
. General information
NOTICE
ED50LE Setup and Troubleshooting.
Reference ED50LE-ED100LE Setup and
Troubleshooting Manual DL4617-001.
.. dormakaba.us website.
Manuals are available for review, download, and printing
on the dormakaba.us website.
.. Dimensions
Unless otherwise specified, all dimensions are given in
both inches (“) and [mm].
.. Building codes and standards.
EDLE installation: observe applicable national and
local building codes.
.. Symbols used in these instructions.
WARNING
This symbol warns of hazards which could result
in personal injury or threat to health.
CAUTION
This symbol warns of a potentially unsafe
procedure or situation.
NOTICE
Draws attention to important information
presented in this document.
TIPS AND RECOMMENDATIONS
Clarifies instructions or other information
presented in this document.

4ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 1
Fig. 1.2.1 LH push
Fig. 1.2.2 LH pull
. Single door configuration examples
Fig. 1.3.1 Push
. Double door configuration examples
Fig. 1.3.2 Pull
Fig. 1.3.3 Double egress

5
ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 2
 Product overview
11 Terminals for
accessory wiring
12 Bag containing
terminals and third
guide pin*
13 Guide pin
* Included with operator
Fig. 2.1.2 Accessory terminals, guide pin
12
11 13
Fig. 2.1.3 ED50LE backplate plate screw kit
HK4053-010
1#12 x 2 1/2" Phillips
FHWS
DF0670 000
21/4-20 x 1 1/2"
PFHMS
DF0671-000
Fig. 2.1.4 Decal kit, low energy HK3137-0X0
1 DD0586-010
2DD0758-010
3DD0762-010
4DD0762-020
8Safety Information
label, low energy
DD1269-040
9Label, Service Call
DD3425-010
Assembly # Item # Quantity
HK-
Single door
decal kit
 
 
 
 
 
 
Assembly # Item # Quantity
HK-
Double door
decal kit
 
 
 
 
 
 
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate thedoor.Door
shouldopenat a slow
smoothpace (4or more
seconds),andstopwithout
impact.
2
. Doormust remainfully open
for aminimum of5 seconds
beforebeginningtoclose.
3
. Doorshouldcloseata slow,
smooth pace(4 ormore
seconds),and stop without
impact.
4
. Inspectthe oorarea.It
should be clean withno
looseparts thatmightcause
userto tripor fall. Keep
tracpathclear.
5
. Inspect door‘s overall
condition. Theappropriate
signageshouldbepresent
and thehardware should
be ingood condition.
6
. Have door inspectedbyan
AAADMcertied inspector
at least annually.
AAADM
American Association o f Automatic
Door Manufacturer s
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualied automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power .
1
3
4
2
8
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
DD0762-010
PUSH
TO OPERATE
9
Assembly # Item # Quantity
HK-
Screw kit
 
 
1
2
. EDLE low energy operator
Fig. 2.1.1 ED50LE operator HX4680-010

6ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 2
. EDLE fine cover kits
No. Part number and description Quantity
HK-X HK-X HK-X
1 HC3459-01X Fine cover single  
2 HC3459-03X Fine cover pair 
3 HC3466-01X ED100/ED250 end cap set 
4 HC3466-01X ED100/ED250 end cap set  
5 HC3466-02X Spindle cover set  
6 HC3468-010 Backplate, ED operator, FC ext.  
7 HC3481-010 ED100/ED250 professional cover bracket 
8 HD4613-020 Logo plate dormakaba ED swing 
9
10 DL4613-001 ED FC logo template instructions 
10 HC3494-010 ED100/ED250 cable tie 
11 HP4613-001 ED FC logo placement template 
12 HL4613-001 ED FC logo template instructions - not shown  
13 HD4613-020 Logo plate dormakaba ED swing  
14 HK3491-001 Backplate connect kit  
15 DL4613-001 ED FC logo template instructions  
16 HP4613-001 ED FC logo placement template  
17 HS3487-010 ED between support assembly 
18 HX3482-010 ED100/ED250 mode switch 
19 HX3484-030 ED power connect cable, 3400 mm 
20 HX3485-030 ED sync cable, 2030 mm 
21 HX3486-030 ED Mode switch 3 position 
Table 2.2.1 Fine cover kit part numbers
.. Fine cover kits.
• HK-X Fine cover kit basic.
• HK-X Fine cover professional single.
• HK-X Fine cover professional pair.

7
ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 2
Fig. 2.2.1 Fine cover kits
HK3401-05X Fine cover professional single
HK3401-07X Fine cover professional pair
3
1
8
11
HK3401-01X Fine cover kit basic
7
6
1
4
22 18 14
16
13
16
13
22
21
4
5
14
6
17
2

8ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 2
. Fine cover kit hardware
1Mounting, extr.
connector
HC3491-010
2M6 x 10 mm SHCS
and washer
HF3495-01Z
3M6 x 10 mm PFHS
HF3496-01Z
Fig. 2.3.4 Mode switch
14 Mode switch
HX3482-010
1Mode switch PCB
2JST HXP 4 pin
connector
3Alpha 1174C 4
conductor 22 AWG
cable, 73" long
1
2
3
10
Fig. 2.3.6 Backplate connect kit HK3491-001
Fig. 2.3.1 End cap sets
3.1 3.2
3.1 End cap set, silver,
HC3466-01A
3.2 End cap set, black,
HC3466-01C
4.1 Spindle cap set, silver
HC3466-02A
4.2 Spindle cap set,
black HC3466-02B
Fig. 2.3.7 Spindle cap sets
Fig. 2.3.2 Cover
bracket
7Cover bracket
HC3481-010
8dormakaba logo
plate
HD4613-020
15 Wire retainer
HX3493
7
Fig. 2.3.3 Wire
retainer
15 Fig. 2.3.8 dormakaba
logo plate
8
4.1
4.2
1
Black
Red
White
Green
4 cond. 22 AWG
1
2
3
14

9
ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 2
. Pull, push arm kits
Fig. 2.6.2 Communication cable,
90 degree RJ45
1Standard push
arm, 8.75" reveal
DC4677-01X
3Screw kit,
HK2719-010
Fig. 2.4.1 Push arm kit, 8.75" reveal
HK4709-01X
1
3
Fig. 2.5.1 Push arm screw kit HK2719-010 Fig. 2.5.2 Pull arm screw kit HK2719-020
10.1 10.2
9.1
9.2
. Arm screw kits
Fig. 2.4.2 Deep pull arm kit, HK4709-12X
1Deep pull arm
DC4678-02X
3Screw kit,
HK2719-020 13
3
2Key switch panel,
RJ45, HX4604-21C
3Key switch panel
HX4604-11C
Fig. 2.6.1 Key switch panels
2
. Optional key switch panels
9.1 10-24 x 1 1/2"
barrel nut
DF2718-01Z
9.2 10-24 x 1/2"
PPHMS
DF3278-01Z
10.1 10-24 x 1 1/2"
barrel nut
DF2718-01Z
10.2 10-24 x 1 1/4"
FHSCS
DF2717-01Z
Communication
cable
 degree RJ
Length Item #
HX- ' [ mm] 
HX- ' [ mm] 
HX- ' [ mm] 
TIPS AND RECOMMENDATIONS
• Wiring diagrams; reference
Appendix B.
1

10 ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 2
. Push arm door stop - option
Fig. 2.8.1 Door stop assembly HS4633-001
21/4" thick base
plate
DC4633-001
3Rubber bumper
DC4633-003
4Shoulder screw
DC4633-004
5.1 1/4 x 1 1/4" Phillips
FHS, black oxide,
SS
5.2 No. 14 x 1 1/4"
Phillips FHS for
sheet metal, zinc
plated steel
Fig. 2.8.2 Mounting screw kit HC4633-005
2
3
4
5.1
5.2
. EDLE axle extension kits
Fig. 2.7.1 [20 mm]
HC4679-001
Fig. 2.7.2 [30 mm]
HC4679-002
Fig. 2.7.3 [60 mm]
HC4679-003
1M8 x 1.25 x 40
SHCS
2M8 x 1.25 x 50
SHCS
3M8 x 1.25 x 80
SHCS
1
3
2

11
ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapters 2 and 3
 Technical data
Maximum wire size
Connector plug
screw size
 AWG
/”
Door
status
X
,,
Sr parameter
Door closed
Door open
Door closed, locked
Com, N.O., N.C.
contacts
. EDLE operator technical data
.. Operating conditions.
Ambient temperature  to  °F [- to  C]
Suitable for dry
rooms only
Relative air humidity:
% maximum, non-condensing
Power supply  Vac ±%, / Hz
. A maximum
Branch circuit
protection (provided
by others)
 A maximum,
dedicated branch circuit
Protection class NEMA  [IP]
Power wiring:
black, white, bare
copper (ground)
 AWG
maximum
Operating noise Maximum  db(A)
.. General specifications.
Operator dimensions
(W x H x D)
" x  / x  /" [ x  x  mm]
" cover standard
Operator weight . lb [. kg]
Power supply for
accessories External power supply required.
Maximum door
opening angle  to ° depending on installation type
.. Inputs
Wire size
Connector plug
screw size
 AWG
/”
Activation
inputs X* Interior, exterior N. O. contact
Safety
sensors X Swing, approach sides.
Night-bank
(intercom
system)
X
,
a
- Vdc/Vac +%
Night-bank
(key switch)
X
,  d parameter Configure for N.O.
or N.C. contact
Deactivation
of drive
function
X
, a d parameter Configure for N.O.
or N.C. contact
.. Outputs
TIPS AND RECOMMENDATIONS
• *X terminal board numbers, reference
Chapter .
3
Fig. 2.11.2 Connect cable
. Double door EDLE operator connection cables
Fig. 2.11.1 Communication (sync) cable
Communication cable Length Item # Quantity
HX- " [ mm]  
Optional
HX-  /" [ mm]  
HX-  /" [ mm]  
1
Connect cable Length Item # Quantity
HX-  /" [ mm]  
Optional
HX-  /" [ mm]  
HX-  /" [ mm]  
Technical data continued on page .

12 ED50LE 09-2021DL4616-004
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 3
. EDLE operating specifications
.. EDLE
.. Integrated functions
Hold open time
Automatic opening dd parameter  to  s
Optional  -  s.
Hold open time
NIght / bank dn parameter  to  s
Hold open time
Manual opening do parameter  to  s
Door blocking
behavior hd parameter Automatic, manual
door modes
Electric strike
delayed opening for
locking mechanism
Ud parameter  to  s
Locking
device
feedback
X
,  Chapter  Motor lock
Wind load control,
maximum Fo, Fc parameters . lb f
 N
Voltage independent
braking circuit
Reference:
Setup and
Troubleshooting
Instructions
Adjustable with
potentiometer
LED status indicators
Green, Red, Yellow
 Vdc power
Error codes
Service interval
Program and Exit
Only switches
Auto, Close, Open
Exit only; Off, On
User interface  button keypad,
 digit display
Slot for upgrade
cards
Extension of
functional range.
Firmware update Firmware update
TMP, temperature
management program Overload protection
IDC, initial drive control Driving phase optimization
Cycle counter CC parameter  to ,,
Power assist function hA, hF, hS
parameters
Drive support for
manual opening of
door
Push & go function PG parameter Auto opening of
door at ° open
TIPS AND RECOMMENDATIONS
• Parameters, reference Setup and
Troubleshooting Instructions Manual.
Maximum power
consumption  watts
Opening force
lbf - N
Fo parameter
Minimum
. []
Maximum
. []
Manual closing force
lbf - N
Fc parameter
Minimum
. []
Maximum
. []
Maximum door
weight, lb [kg]  [ kg) Depending on door
width and application.
Door width Minimum
"
Maximum
"
Maximum opening
speed, °/s  May be limited by
door weight after
learning cycle.
Maximum closing
speed, °/s 
Axle extensions /" [ mm]
 /" [ mm]
Reveal depth for pull
arm with CPD lever  to  /" [ to . mm]
Reveal depth for
standard push arm  to  /" [ to  mm]
Reveal depth for deep
push arm  to  /" [ to  mm].

13
ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 4
. EDLE terminal board interfaces
TIPS AND RECOMMENDATIONS
• Use documentation provided
with each device for electrical
installation.
Fig. 4.1.1 Terminal board electrical connections
1Green LED
2Yellow LED
3Red LED
4Key (red insert)
location in socket.
Assigned plug has
tab in same location
broken off.
5Jumpers, factory
installed at following
terminals:
•  and a
•  and *
•  and *
6DCW upgrade card
plug Not used.
7Fire protection
upgrade card plug.
Not used.
TIPS AND RECOMMENDATIONS
• Do not connect system
accessories to board until
operator has been
commissioned and learning
cycle performed (Setup and
Troubleshooting Manual).
 EDLE terminal board interfaces
97 98 99 30 31 32 34 33 3335 136144a
3BA157 57a 14231413115 17 311113 3
43 36463621G 3
+ 24 V
Signal input 0 V
Partial Open
Permanent Open
Exit Only
Automatic
Off
N.C.
COM
Test output
X5X4
X3
X6 X9 X1 X7
+ 24 V
X8
0 V
X10
8 - 24 AC/DC + 5% Wet
DCW bus
Activation inputs
Interior Exterior
Night-
bank
input
+ 24 V
Signal input 0 V + 24 V
+ 24 V Signal input
Signal input 0 V
0 V
Test output
0 V
24 V
Brake coil signal
Output
COM
N.O.
N.C.
0 V
Locking relay
Maximum current:
1A, 48 V DC/AC
Locking feedback contact
0 V
0 V
+ 24 V
0 V
0 V
Signal input
N.O.
Smoke
detectors
Emergency
close
Night
trigger
Program, exit only
switches
Door status
24 VDC
Class II
1
2
3
4
5
6
7
55
Safety sensors
Swing side Approach side

14 ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 5
 EDLE door signage
Fig. 5.1.1 AUTOMATIC CAUTION DOOR decal
Fig. 5.1.2 ACTIVATE SWITCH TO OPERATE decal
Fig. 5.1.3 PUSH TO OPERATE, PULL TO OPERATE decals
. Low energy operator
.. Overview
Signage and warnings are specified in ANSI /BHMA
A., American National Standard for Power Assist
and Low Energy Power Operated Doors.
.. All low energy doors.
. AUTOMATIC CAUTION DOOR decal.
• All low energy doors shall be marked with signage
visible from both side of door with the words
"AUTOMATIC CAUTION DOOR".
• Signs shall be mounted " ± " from floor to
centerline of sign.
.. Knowing act switch used to initiate door operation.
. ACTIVATE SWITCH TO OPERATE decal.
• When a knowing act device is used to initiate operation
of door operator, door shall be provided with sign on
each side of door where switch is operated with
message "ACTIVATE SWITCH TO OPERATE".
.. Push/Pull used to initiate door operation.
. PUSH TO OPERATE, PULL TO OPERATE decals.
• When push/pull is used to initiate operation of door
operator, doors shall be provided with the message
"PUSH TO OPERATE" on push side of door and
"PULL TO OPERATE" on pull side of door.
DD-
DD- DD-
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD-
1Activate Switch to
Operate DD0758-010
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010 1
2Push to Operate
DD0762-010
3Pull to Operate
DD0762-020
DD0762-010
PUSH
TO OPERATE 2
DD0762-020
PULL
TO OPERATE 3
Push to Operate
. Door signage, low energy swing door per ANSI / BHMA A.
Fig. 5.2.1 Push / Pull initiation of door operation
Pull to Operate
2Push to Operate
DD0762-010
3Pull to Operate
DD0762-020
Fig. 5.2.2 Knowing act device initiation of door operation
1Activate Switch to
Operate DD0758-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
3
CAUTION
DOOR
AUTOMATIC
DD0586-010
2
DD0762-010
PUSH
TO OPERATE
CAUTION
DOOR
AUTOMATIC
DD0586-010
1
CAUTION
DOOR
AUTOMATIC
DD0586-010
1
DD0758-010
ACTIVATE SWITCH
TO OPERATE
dormakaba
DD0758-010
DD0758-010
ACTIVATE SWITCH
TO OPERATE
dormakaba
DD0758-010

15
ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 5
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
should open at a slow
smooth pace (4 or more
seconds), and stop withou
t
impact.
2
. Door must remain fully open
for a minimum of 5 seconds
before beginning to close.
3
. Door should close at a slow,
smooth pace (4 or more
seconds), and stop without
impact.
4
. Inspect the floor area. It
should be clean with no
loose parts that might cause
user to trip or fall. Keep
traffic path clear.
5
. Inspect door‘s overall
condition. The appropriate
signage should be present
and the hardware should
be in good condition.
6
. Have door inspected by an
AAADM certified inspector
at least annually.
AAADM
American Association of Automatic
Door Manufacturers
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
Fig. 5.3.1 Safety
information
label
DD1269-040
. Safety label, low energy swing
doors
.. Low energy swinging door safety information
label (Fig. ..).
This AAADM label outlines safety checks that should be
performed daily on low energy swinging door controlled
by an EDLE operator.
.. Safety information label location.
Place label in a protected, visible location on door frame,
near program switch panel if possible.
.. Annual compliance section of label.
This section of label is only completed on low energy
swing doors that comply with ANSI/BHMA A.
standard and pass inspection by an AAADM certified
dormakaba USA, Inc. technician.
.. Additional annual compliance inspection labels.
Place additional labels over annual compliance
inspection section of safety information label.
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE: ______________
by AAADM Certified
Inspector
Number: ___________
Fig. 5.3.2 Annual
compliance
inspection label
Fig. 5.2.3 Double door, Push / Pull, push to operate
Fig. 5.2.4 Double door, Push / Pull, pull to operate
2Push to Operate
DD0762-010
3Pull to Operate
DD0762-020
CAUTION
DOOR
AUTOMATIC
DD0586-010
2
CAUTION
DOOR
AUTOMATIC
DD0586-010
2
DD0762-010
PUSH
TO OPERATE
DD0762-010
PUSH
TO OPERATE
CAUTION
DOOR
AUTOMATIC
DD0586-010
3
CAUTION
DOOR
AUTOMATIC
DD0586-010
3
DD0762-020
PULL
TO OPERATE
DD0762-020
PULL
TO OPERATE

16 ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 6
 Recommended tools and torque chart
Fig. 6.1.1 Recommended tools
. Recommended tools
1T-handle hex key, 5
mm
2Hex keys, 2.5 mm,
3 mm, 6 mm
3Screwdriver, flat
blade
4Door pressure
gauge, 0 to 35 ft - lbf
5Screwdriver, Phillips,
#2, #3
6Torque wrench,
3 to 50 ft lb min.
6.1 Metric hex key
sockets
7Open end wrench,
13 mm
8Screwdriver, flat
blade, M2 (1/16 to
3/32")
Fastener size ft lb
M .
M 
M 
M 
M 
. Standard tightening torque
.. Standard tightening torque
Fastener Drill bit size
# wood screw Hardwood
/"
Softwood
/"
# wood screw Hardwood
/"
Softwood
/"
# wood screw Hardwood
/"
Softwood
/"
/ - metal self
tapping screw /"
- barrel nut /"
. Drill bits
.. Drill bit sizes for fasteners Fig. 6.3.1 Drill bit
8
6
6.1
7
5
3
1
4
2

17
ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 7
Fig. 7.1.1 Assembly on hinge side, pull version with slide channel CPD and 1/2" [25] pivot pin
B
D
A
C
Reveal depth maximum 2 3/8” [60]
Upper edge door
Upper edge door
Space for cable feed
5 7/8”
[150]
4 3/16”
[106]
1 3/4”
[45]
1 1/4”
[32]
3 15/16”
[100]
1 3/4”
[45]
4 3/4”
[120]
4 3/4”
[120]
4 3/4”
[120]
3 3/4”
[95]
7 11/16”
[195]
Ø 1/4”
[6,6]
2 1/2”
[63]
17 3/4”
[451]
1 1/4”
[31]
1/8”
[3]
When CPD lever is used, about 1 3/16” [30]
must be deducted from the actual reveal
depth when the parameter is set.
 EDLE operator installation templates
. EDLE installation templates
Axle extension EDLE A B C D
Inches mm Inches mm Inches mm Inches mm
Standard ● /    /   / 
/" [] ●  /   /   /   / 
 /" [] ●  /   /   /   / 
 /" [] ●  /   /   /   

18 ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 7
Fig. 7.1.2 Assembly on hinge side, pull version with slide channel CPD and 1" [50] pivot pin
B
D
A
C
Upper edge door
Upper edge door
Space for cable feed
5 7/8”
[150]
4 3/16”
[106]
1 3/4”
[45]
1 1/4”
[32]
3 15/16”
[100]
2 1/2”
[63]
4 3/4”
[120]
4 3/4”
[120]
4 3/4”
[120]
3 3/4”
[95]
1 3/4”
[45]
Ø 1/4”
[6,6] 17 3/4”
[451]
1/8”
[3]
1 3/4”
[44]
When CPD lever is used, about 1 3/16” [30]
must be deducted from the actual reveal
depth when the parameter is set.
Reveal depth maximum 2 3/8” [60]
7 11/16”
[195]
Axle extension EDLE A B C D
Inches mm Inches mm Inches mm Inches mm
Standard ●  /   /  /   / 
/" [] ●    /   /   / 
 /" [] ●  /   /   /   / 
 /" [] ●  /   /   /   / 

19
ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 7
Fig. 7.1.4 Assembly on opposite hinge side, with push arm assembly
B
D
C
A
Lower edge frame
Lower edge frame
Space for cable feed
5 7/8”
[150]
4 3/16”
[106]
1 3/4”
[45]
1 1/4”
[32]
3 15/16”
[100]
9 5/8”
[245]
Ø 1/4”
[6,6]
1 5/16
[33]
1 31/32
[50]
4 3/4”
[120]
4 3/4”
[120]
4 3/4”
[120]
3 3/4”
[95]
1 3/4”
[45]
2 1/2”
[63]
J8 - 0 - 8” [0 - 225]
J12 = 0 - 12” [0 - 500]
Axle extension EDLE A B C D
Inches mm Inches mm Inches mm Inches mm
Standard ● /    /   / 
/" [] ●  /   /   /   / 
 /" [] ●  /   /   /   / 
 /" [] ●  /   /   /   

20 ED50LE 09-2021DL4616-002
dormakaba ED50LE operator – Fine cover
Installation Instructions
Chapter 8
 EDLE operator installation
. Installation preparation
NOTICE
Installation steps listed in Chapter 8 through 11
are a recommendation. Structural, local
conditions, available tools, or other factors or
circumstances may require modification to
these steps.
WARNING
EDLE system should be installed by trained
and knowledgeable installers experienced in
installation and commissioning of swing door
operators.
The installer should be familiar with all
applicable local and national building code
requirements, and with requirements of
current ANSI/BHMA standard A., Power
Assist and Low Energy Power Operated
Doors.
.. Door frame and door.
CAUTION
Insure area around door frame, adjacent walls
and door is readily accessible and free of
objects and debris.
.. Knowing act devices.
. Verify knowing act devices planned for or in place for
the door.
TIPS AND RECOMMENDATIONS
Knowing act device wiring should be planned
for prior to operator installation.
.. EDLE mounting plate installation preparation.
CAUTION
Using applicable EDLE installation template
(Chapter ), holes for mounting plate
fasteners must be located and drilled into door
frame, wall or substructure prior to mounting
plate installation.
CAUTION
Mounting plate installation must be orientated
with  Vac connection towards door hinge side.
.. EDLE mounting plate extension used with
optional full door width cover.
TIPS AND RECOMMENDATIONS
Mounting plate extension is included
for full width cover installation.
• Reference Appendix A for mounting
plate extension and full width
cover installation.
.. EDLE  Vac electrical installation.
WARNING
Work on electrical equipment and  Vac
wiring installation must be performed only by
qualified personnel!
WARNING
115 Vac wiring to ED50LE operator must
conform to local and national electrical codes.
NOTICE
Double door Installation:
Repeat steps in Chapter 8 for each ED50LE
operator
TIPS AND RECOMMENDATIONS
ED50LE installation.
The ED50LE must be installed on an interior
door.