Dormakaba ED50 User manual

ED50/ED100/ED250 1DL4615-015 www.dormakaba.com 01-2020
Quick Start Guide
ED50/ED100/ED250
• The ED operator must be completely installed per the
applicable dormakaba Installation Instruction Manual.
• Door must be closed. Both program switches
in the CLOSE “” position.
• All terminal blocks need to be installed.
No safety sensors connected.
Step 
Power switch to ON position.
• A series of numbers and letters will show up
on the display.
• This will stop after two horizontal dashes
sideby side move up and down several times.
Step 
While the dashes are moving up and down,
press the bottom button on the display.
• This will identify which way the unit is
mounted.
• Letters and numbers will now display right
side up.
The display will show a “P“ on the right with a
rotating segment on the left.
When the braking circuit plug is in the
correct position the door will easily Press
open and close slowly. If the door is very
hard to Press open change the jumper
position.
28
A
B
> 3s Reset
< 3s Quit
> 3s
PRG
< 3s LEARN
Fact-Setup
> 3s
> 8s
Step Directions Expected results

Press and hold the right button until Parameter
ID is displayed (approximately  seconds), then
release the button.
Parameter ID will appear (ex. AS).
Press the right button. Displays the current setting.
Press the right button. Display will flash the current setting.
Press the up and down buttons to change the
setting.
Press the right button to accept the changes. Displays the new parameter
setting.
Press the left button to return to the
programming menu.
Displays the current Parameter ID
(Step ).

Press the down button to go to the next
parameter setting (or) Go back to Step .
Press the left button to exit programming menu. Display will show a rotating
segment and a “”.
NOTICE
This guide is intended to be used as a reference to assist a trained and
certified AAADM technician in programming the dormakaba:
• ED operator in accordance with ANSI A. Standard for
Low Energy Power Operated Doors.
• ED/ED operators in accordance with ANSI A. or
ANSI A. Standard for Power Operated Pedestrian Doors.
Braking circuit plug position
A – Pull arm B – Press arm
Power fail closing speed.
• The door must be adjusted to close in
no less than three seconds but a
minimum of five seconds is recommended.
WARNING
If braking circuit plug is inserted
incorrectly, brake circuit will not
work. The door can close at high
speed!
WARNING
Verify power fail closing speed
and braking circuit plug position
before programming the door
and completing a learn cycle.
All three required
parameter settings
(AS, rd, Tb) must
be made to flash
even if the value
does not need to
be changed before
the door will move
to the learn cycle.

ED50/ED100/ED250 2DL4615-015 www.dormakaba.com
T: 717-336-3881 12-2019
Step Configuration
Parameter
Range
Factory
Settings
* Factory setting.
 Installation
type -
0* Pull arm with track, wall mounting
on pull (hinge side).
Press arm, wall mounting on
approach (non-hinge side).
Press arm with track, wall mounting
on approach (non-hinge side).
Overhead concealed (OHC) right
hand.
 Overhead concealed, left hand.
 Reveal
depth
ED/
- to 
ED
- to 
0*
Reveal depth rd is set in increments
of  mm (/”).
Example:  =  mm ( /”)
 Door width
ED/
 to 
ED
 to 
10*
The astragal is included in the door
width.
Door width Tb is set in increments
of  mm (”).
Example:  =  mm (”).
Reveal depth rd
Door width Tb
Learn Cycle: a ““ displayed on the right side and a rotating segment
on the left indicates the unit is ready for a learn cycle.
• To start the learn cycle, press and hold the bottom button for
until the display changes (approximately three seconds).
The door will make several movements and the display will cycle
through several letters and numbers.
When the display stops at “” push the door open to the desired
opening angle between  and  degrees, then let go of the door
and press the bottom button to continue the learn cycle.
The operator will complete the learn cycle.
• When finished, there will be two horizontal bars side by side on the
display.
• You can now continue with the programming and customize the
door as desired.
rd Inches
- -  /
- -/
- -/

 /
 /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
 
  /
  /
Tb Inches



Tb Inches
 
 
 
rd Inches
  /
  /
 
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
  /
ED50/ED100/ED250 ED250
If the door closes and an “F” is displayed, this is an indication
that the spring force is too low.
. Turn off the power.
. Increase the spring force.
• The spring should have a minimum of  turns and a
maximum of  to  turns ( on ED).
. Restart the learn cycle. Press and hold the bottom button
until the display changes (approximately three seconds).