Dormakaba TS93 GSR PT User manual

TS93 GSR PT
Surface Applied Closer
Push side track mount and coordinator system
Installation instructions
08281850 – 08-2019
| EN |

2TS93 GSR Surface Applied Closers 08-2019
08281850
dormakaba TS93 GSR PT Installation Instructions Table of Contents
Table of contents
 Technical specifications 
. Overview 
. Size selection chart 
. Tools recommended 
. Surface closer system 
. Handing the door 
 Installation instructions 
. Installing the back plate 
. Installing the surface closer 
. Installing the slide channel 
. Installing the main arm 
. Secure main arm 
. Installing the coordinator system 
 Adjustments 
. Adjust closing speeds: sweep, latch, backcheck,
delayed action 
. Adjust optional hold open 
. Adjust spring force 
 Install covers 

dormakaba TS93 GSR PT Installation Instructions
08281850 08-2019TS93 GSR Surface Applied Closers 3
Technical specifications
 Technical specifications
. Overview
Door Width
Closer Interior/
Exterior
'-"
min.
’-"
max.
’-”
max.
’-”
max.
’-”
max.
’-”
max.
’-”
max.
TS Interior • • NA NA
TS Interior NA NA NA NA • • •
Caution: sex nuts are required for attachment of
components to unreinforced doors and to wood
or plastic faced composite type fire doors, unless
an alternative method is identified in the
individual door manufacturer’s listings.
Maximum door opening degree is °.
Minimum door width is ”.
Hold open range is from ° to ° with optional
hold open kit.
Arrows on closer mounting plate point upward.
A carry bar should be installed to insure that the
active door is opened enough for the inactive
door to close.
Recommended carry bars:
DORMA carry bar MK- (up to ’-” wide door)
DORMA carry bar MK- (’-” and wider door)
Installation instructions are included with carry
bar.
Follow included template to properly prepare
door and frame for all accessories of the closer
installation.
Know the swing of the door which is being
installed prior to installation.
Make sure door efficiently operates prior to
installing closer.
Verify closer spring size prior to installation.
Table 
Table 
Drill bits: Pozidriv PZ- .mm, mm, mm hex key
Metal: No.  & - tap # Phillips screwdriver /” box wrench
Wood: /” /” flat head screwdriver ” adjustable wrench
. Size selection chart
. Tools recommended

dormakaba TS93 GSR PT Installation Instructions
08281850 08-2019TS93 GSR Surface Applied Closers
4
Surface closer system
Handing the door
Fig.
Hinge Hinge
Exterior side of door
Interior side of door
Left hand door (LH) Right hand door (RH)
The surface closer is comprised of the following components.
. Closer body: “B” body
. Main arm
. Active track assembly
. Inactive track assembly
. Pinion
. Track covers and center cover
. Closer cover
. Closer end caps
. Connecting channel
. Handing the door
Fig.
. Surface closer system
783/4 3/4
6
9
6
5 1 2
2

dormakaba TS93 GSR PT Installation Instructions
08281850 08-2019TS93 GSR Surface Applied Closers 5
Installing back plate
Installing surface closer
. Installing the back plate
 Installation instructions
NOTE: Orient pinion closest to hinge. .. Secure closer body to plate.
• Use four M x mm screws for each closer.
. Installing the surface closer
Fig.
Fig.
.. Secure plate to door.
• Use four - x /” PH screws [# x -/”
wood screws] provided for each plate.
NOTE: Ensure arrows point
in direction of arm location.
Left hand door
Right hand
door
Backplate
-x/"
.. Secure left and right hand mounting angles to
frame.
• Use  FH screws each.
.. Cut middle filler angle.
• Secure using  FH screws.
Mounting angles
Mounting angle
flat head screws
Mounting angles
Middle filler angle
Middle filler angle
flat head screws
CUT
NOTE: When cutting filler
angle, be sure to plan for the
conduit hole /” [].
Toward the
hinge
Toward the
hinge
Closer
Pinion
Left hand
door
Right hand
door
Pinion

dormakaba TS93 GSR PT Installation Instructions
08281850 08-2019TS93 GSR Surface Applied Closers
6
Installing slide channel
Installing main arm
. Installing the main arm
Fig.
NOTE: EXAMPLE: Left hand active door shown. For right hand
active installations, install active track assembly on right hand
door and inactive track assembly on left hand door.
.. Orient track with coordinator toward center of doorway.
.. Secure track to door frame.
• Use two M FH screws.
.. Insert end caps into track.
.. Secure end of track through end caps.
• Use two M FH screws.
.. Slide end cap covers onto end caps.
. Installing the slide channel
Fig.
.. Attach /” wrench to bottom pinion.
.. While looking up, rotate pinion (square) until it aligns to
square hole on arm.
LH = turn ° counter-clockwise
RH = turn ° clockwise
.. Arm is parallel to door.
.. Secure with Mx socket head fastener.
• Use an M hex key.
Left hand door
End cap
covers
End caps
M FH
Right hand door
(Inactive)
Left hand door
(Active)
Coordinator towards
center of doorway
M FH
Main arm
Right hand door
(Inactive)
Left hand door
(Active)
Mx
Pinion

dormakaba TS93 GSR PT Installation Instructions
08281850 08-2019TS93 GSR Surface Applied Closers 7
Secure main arm
Installing coordinator system
. Secure main arm
Fig.
.. Secure arm to slide shoe.
• Use one shoulder bolt and an mm hex key.
NOTE: Depress trigger dial to allow active slide shoe to
move freely. If locking pin falls out, discard after
completing installation.
.. Close both doors.
.. Press lever with roller against door.
.. Tighten hex screw.
.. REMOVE alignment screw.
Arm
Slide shoe
Shoulder
bolt
Left hand door (Active) Right hand door(Inactive)
Trigger dial
Lever with
roller
Hex screw
Alignment screw
END VIEW

dormakaba TS93 GSR PT Installation Instructions
08281850 08-2019TS93 GSR Surface Applied Closers
8
Coordinating system
. Installing the coordinator system
Fig.
.. Close both door leafs.
.. Push plastic guide element up against slide
shoe.
.. Fully wind trigger dial (towards door frame).
.. Align connecting channel with trigger dial per
image above.
.. Mark and cut connecting channel.
.. Open active leaf to retract clamping rod.
.. Active door: Insert connecting channel into
trigger dial.
.. Inactive door: Insert connecting channel into
plastic guide.
.. Unwind trigger dial (away door frame) until
active door starts to close. Clamping plate
should be perpendicular to clamping rod.
.. Tighten set screw to secure trigger dial.
NOTE: The locking pin can be discarded once system has
been installed.
CUT LENGTH
Cut mark
reference
Plastic guide
element
Slide shoe
Trigger dial
Connecting
channel
Clamping rod
Trigger
dial
Connecting
channel
Set
screw
Locking
pin
Plastic
guide
Clamping plate

dormakaba TS93 GSR PT Installation Instructions
08281850 08-2019TS93 GSR Surface Applied Closers 9
Adjust closing speeds
Adjust hold open
 Adjustments
Confirm closer spring size prior to making any
closing speed adjustments.
Do not back valve heads out beyond closer casting.
Door should close in  to  seconds from º.
Maximum opening angle is º.
Do not close valves completely.
. Adjust closing speeds: sweep, latch, backcheck, delayed action
Fig.
.. Adjust door position:
• Adjust hold open angle: loosen adjustment
screws using an M hex key.
• Slide hold open mechanism to desired location
and re-tighten adjustment screws.
.. Hold open activation:
• Place door in hold open.
• Deactivate: When clips are released from slide
shoe.
• Activate : When clips are pressed against inside
of slide shoe.
.. Adjust hold open force:
• Decrease force: spin dial away from door frame
• Increase force: spin dial towards door frame
NOTE: Do not set release force too high. Damage may
occur to door, hinges or GSR system.
. Adjust optional hold open
Fig.
Increase
Decrease
Decrease
Increase Backcheck &
Delayed action
Sweep & Latch
Speed
.. Adjust the closing sweep speed for the area from ° - °
• Increase sweep speed: Turn valve counter-clockwise
• Decrease sweep speed: Turn valve clockwise.
.. Adjust the closing latch speed for the area from ° - °.
• Increase latch speed: Turn valve counter-clockwise
.. Adjust the opening backcheck for the area from
° - °.
• Increase resistance: Turn valve clockwise
• Decrease resistance: Turn valve counter-clockwise.
.. Adjust the closing delayed action for the area from
° - °.
• Increase delayed action: Turn valve counter-clockwise
• Decrease delayed action: Turn valve clockwise
Latch
Backcheck
Sweep
Latch
Backcheck
Delayed action
°
°
°
°
Sweep
Delayed action
Adjustment
screws
Dial
Hold open
mechanism

dormakaba TS93 GSR PT Installation Instructions
08281850 08-2019TS93 GSR Surface Applied Closers
10
Adjust spring force
Secure covers
. Adjust spring force
Fig.
Increase
Decrease
TS
NOTE: Supplied with a size  spring setting.
Barrier free openings: Take an opening force reading
from the pull on the door. If required, adjust the spring
force to meet the barrier-free requirement.
• Decrease force: turn counter-clockwise ( max
turns)
• Increase force: turn clockwise ( max turns)
Depending on opening conditions, a door adjusted to
meet barrier-free forces may not have sufficient power
to reliably close and latch the door.
TS
NOTE: Supplied with a size  spring setting.
• Increase force: turn clockwise  times (max)
Regular Mount, Pull side closers
Closer size Max door
weight (lbs)
Door width Full turns
Interior Exterior
TS
  '" --- 
  ' '" +
  '" ' +
  ' '" +
TS   ' '" -
  '" ' 
 Install covers
.. Snap both end covers onto closer body end caps.
.. Remove un-needed tab, and snap cover over closer body.
.. Secure with one - Phillips pan head screw.
.. Center cover: Measure distance between track covers,
and subtract /”. [X - -/” = center cover length]
.. Cut center cover to length measured, and slide over
coordinator system.
.. Snap center caps on to track.
Fig.
Tab
- pan
head screw
Closer cover
End caps Center
caps
Center
cover
Track
cover
Track
cover X

www.dormakaba.com
dormakaba
DORMA USA, Inc.
1 Dorma Drive, Drawer AC
Reamstown, PA 17567
USA
T: 717-336-3881
F: 717-336-2106