Dormakaba TS 98 XEA User manual

EN
GSR XEA
GSR-EMF XEA
Mounting instructions
Contents
1 About this manual 2
1.1 Information about the manual 2
1.2 Target groups 2
1.3 Provided documents 2
1.4 Symbols and abbreviations used 2
1.4.1 Safety instructions 2
1.4.2 Further labeling 2
1.4.3 Tool symbols 2
1.5 Glossary 2
2 Safety 3
2.1 Intended use 3
2.2 Limitation of liability 3
2.3 Prerequisites for the operation of catching
devices 3
3 Product description 3
3.1 EMF 3
3.2 Technical data of the EMF 3
4 Mounting 4
4.1 Prepare the mounting of the slide rail 4
4.2 Mount the sliding rail of the fixed leaf 4
4.3 Mount the active leaf slide rail 4
4.4 Mount the door closer 4
4.5 Shorten the connecting tube 4
4.6 Mount the connecting tube 4
4.7 Set the sequential locking control 4
4.8 Check the sequential locking control 5
4.9 Connect the EMF 5
5 Start up 5
5.1 Set the fixture point 5
5.2 Set the release force 5
5.3 Mount the paneling 5
5.4 Check the EMF 6
5.4.1 Release EMF manually 6
5.4.2 Delete EMF electronically 6
6 Operating 6
6.1 Open and lock door 6
6.2 Close door 6
7 Dismounting, recycling and disposal 6
WN 059376 45532 – 2017-10
dormakaba Deutschland GmbH
DORMA Platz 1
D‑58256 Ennepetal
17
0432‑CPR‑00026‑60 EN 1155: 1997/A1: 2002/AC:2006 3 8 3‑5 1 1 4
DOP_0146
dormakaba Deutschland GmbH
DORMA Platz 1
D‑58256 Ennepetal
17
0432‑CPR‑00026‑83 EN 1158: 1997/A1: 2002/AC:2006 3 8 3‑7 1 1 4
DOP_0147

1 About this manual
1.1 Information about the
manual
This instruction is part of the product. The instruction
contains essential instruction for the safe operation.
Therefore, the instruction must be carefully read
before using the product. This instruction must be
kept during the service life of the product and must
be passed on with the product. This instruction
describes the installation, startup, maintenance and
disassembly of the slide rail system GSR XEA and the
sliding rail system GSR‑EMF XEA. The text of the
instruction is supported by figures in a separate figure
part. The chapter numbers in the text can be found
again top left in the figures in the figure part. There is
not always a figure in the figure part to support a
chapter in the text. The figures show the installation
of the action leaf DIN‑L. Accordingly proceed mirror‑
inverted with the action leaf.
1.2 Target groups
The installation, startup, maintenance and
disassembly must only be carried out by skilled staff
which has been authorized by dormakaba. The
operation of the slide rail system may be carried out
by any person who is mentally and physically able.
1.3 Provided documents
• Mounting instruction
Additionally with GSR‑EMF XEA:
• Data sheet about the use of arrest systems
1.4 Symbols and abbreviations
used
1.4.1 Safety instructions
WARNING
This statement indicates a possible
hazardous situation which may result in
death or severe injuries if ignored.
ATTENTION
This statement indicates a possible
hazardous situation which may result in
property or environmental damage if
ignored.
1.4.2 Further labeling
2.1. Action steps in diagrams
1 2 Position numbers of parts
Figure shows installation directly on the
door lintel
Figure shows installation options with
mounting plates
1220‑1350
Figure shows installation steps for door
widths 1220‑1350 mm
>1350
Figure shows installation steps for door
widths > 1350 mm
1.4.3 Tool symbols
Tape line
Saw
Allen wrench,
z. B. wrench size 3
1.5 Glossary
E End switch ‑ releases fixed leaf if
active leaf is shut.
EMF Electromechanical locking device
G Active leaf
GSR Slide rail door coordinator
RMZ Smoke detection panel
S Fixed leaf
TS Door closer
2GSR XEA/GSR-EMF XEA 2017-10
dormakaba
WN 059376 45532
About this manual
Mounting instruction

2 Safety
2.1 Intended use
The glide rail system GSR XEA is used for the
sequential locking control of 2 winged doors. The glide
rail system GSR‑EMF XEA is used for the sequential
locking control and for the locking mechanism to keep
open 2 winged doors. The locking mechanism is used
in conjunction with external RMZ to keep open fire
and smoke protection closures. Fire and smoke
protection closures must meet the building regulation
requirements ‘’self‑locking’’. The electromechanical
locking device is no substitution for a door stop. The
locking device is released manually or via an external
RMZ.
2.2 Limitation of liability
The manufacturer does not assume liability for
damages in the following events:
• Nonobservance of this instruction.
• A deviating application of the intended use.
• The assignment of insufficiently skilled staff.
• Unauthorized modifications.
• Technical alterations.
• The use of spare parts which are not authorized.
2.3 Prerequisites for the
operation of catching devices
The use of the slide rail systems as catching devices
(GSR‑EMF XEA) is subject to special regulations by
reason of official admission standards. These
regulations refer in particular to the inspection, the
continuing surveillance and the maintenance. Follow
the details from the data sheet about the use of
catching devices.
Additional requirements apply for the use as fire and
smoke protection closures in conjunction with the
external RMZ and RM. A separate verification of
suitability is required for the respective fire / smoke
protection door.
3 Product description
GSRXEA
The GSR XEA comprises the following components:
• Slide rail system with sequential locking control
The GSR XEA is intended for the mounting on the
hinge side. The GSR XEA is suitable for DIN‑L and
DIN‑R doors.
GSR‑EMFXEA
The GSR‑EMF XEA comprises the following
components:
• Slide rail system with sequential locking control
• Built‑in electromechanical locking device
The GSR‑EMF XEA is intended for the mounting on
the hinge side. The GSR‑EMF XEA is suitable for
DIN‑L and DIN‑R doors. The GSR‑EMF XEA is
available in three versions:
• GSR‑EMF1:
The fixed leaf is fitted with an EMF. Both leaves
may be locked. The sequential locking control keeps
the active leaf open.
• GSR‑EMF2:
The active leaf and fixed leaf are each fitted with an
EMF.
The active leaf can either be locked independently
from the fixed leaf or both door leaves can be
locked.
• GSR‑EMF1G:
The active leaf is fitted with an EMF. The active leaf
can be locked. The fixed leaf cannot be locked.
Each door leave that is fitted with an EMF can be
locked in an opening angle of approx. 80°–130°.
Statements
Statement
(lever length)
Door width
(mm)
GSRXEA
GSR‑EMFXEA
VK (320 mm) 1220–1350
V (375 mm) 1350–2500
VL (375 mm) 2500–2800
3.1 EMF
The EMF is an electromechanical locking mechanism
with adjustable release force, which enables locking
the door without spring back. After a cut‑off of power
supply, the locking device disengages and the door will
be closed securely through the door closer.
3.2 Technical data of the EMF
Operating voltage: 24V DC
in France also 48VDC
Power consumption: EMF 1, 1G 1,4 W
EMF 2 2,8 W
in France also
EMF 1, 1G 2,2 W
EMF 2 4,4 W
Duty cycle: 100 % ED
Release torque: approx. 25 – 65 Nm at 90°
opening angle (dependent
on the set closing force on
the closer)
Door opening angle:
EMF 1
EMF 2
EMG 1G
Active leaf Fixed leaf
max. 180° max. 130°
max. 130° max. 130°
max. 130° max. 180°
The drive happens via an external RMZ.
3GSR XEA/GSR-EMF XEA 2017-10
dormakaba Mounting instruction
WN 059376 45532
Safety

4 Mounting
The mounting of the slide rail system takes place
directly on the door lintel or optionally with a
mounting plate.
4.1 Prepare the mounting of the
slide rail
The slide rail can be mounted in two different options:
Option A = Mounting directly on the door lintel
Option B= Mounting with mounting plate
1. Measure the lever length (V, VL, VK) and using the
appropriate hole pattern.
2. Prepare the power supply (24 V/48 V DC) from the
smoke detection panel to the EMF in version with
EMF.
3. Take into account the mounting position on active
leaf G and fixed leaf S.
4. Mark the fixing points for the closer and the slide
rails according to the hole pattern.
5. Drill the holes.
6. Drill the hole for the connecting cable
(24V/48VDC) Ø8mm in versions with EMF.
7. Laying cables in versions with EMF.
Additional mounting steps for option B (mounting
with mounting plates)
8. Shorten the middle mounting plate.
9. Mount the mounting plate on the door profile.
4.2 Mount the sliding rail of the
fixed leaf
1. Insert the end caps connector into the slide rail.
2. A Tighten the slide rail.
BTighten the slide rail
on the mounting plate.
4.3 Mount the active leaf slide rail
1. Insert the end caps connector into the slide rail.
2. A Tighten the slide rail.
BTighten the slide rail
on the mounting plate.
4.4 Mount the door closer
1. Mount the door closer and lever to the door leaf
according to the enclosed instructions for the
door closer.
2. Adjust the door closer.
4.5 Shorten the connecting tube
1. Measure the dimension X.
2. Shorten the connecting tube to the dimension
X‑47 mm.
4.6 Mount the connecting tube
1. Open of the active leaf.
2. Open of the fixed leaf.
3. Screw in the adjusting sleeve up to marking.
4. Insert of the connecting tube into the adjusting
sleeve of the active leaf slide rail.
5. Insert the slide of the fixed leaf slide rail and fit
the connecting tube into the retainer.
4.7 Set the sequential locking
control
Only if the clamp plate is adjusted correctly, can the
active leaf be moved into the direction of closing
properly while the fixed leaf is closed.
The clamp plate is adjusted correctly when the
connecting tube pushes the clamp plate into a
rectangular position via the adjusting sleeve.
Carrying out the setting as follows:
1. Close the fixed leaf.
2. Close the active leaf.
3. Unscrew the adjusting sleeve manually so far that
the pin 2drops out. In the process, the clamp
plate must be in a rectangular position to the
clamping rod 1. The pin holds the sequential
locking control in a neutral position without
hindering and will not be required after mounting.
4. Secure the adjusting sleeve with the plastic bolt.
4GSR XEA/GSR-EMF XEA 2017-10
dormakaba Mounting instruction
WN 059376 45532
Mounting

4.8 Check the sequential locking
control
WARNING
Risk of smoke inhalation
If the GSR‑EMF XEA is used as fire and
smoke protection closure the sequential
locking control must work perfectly. If the
sequential locking of the door leaves is not
achieved the catching device must not be
used on fire and smoke protection doors.
• Mount a catch cap.
1. Open of the active leaf.
2. Open of the fixed leaf.
3. Hold the fixed leaf.
4. Change the position of the active leaf to the
opening direction. The active leaf must be set in
each position.
5. Let the fixed leaf close. The active leaf must only
close automatically when the fixed leaf is closed.
4.9 Connect the EMF
Only for GSR‑EMF XEA
1. Lay the EMF‑connecting cables of the fixed leaf
to the active leaf in a way that it is not resulting
in jamming the connecting rod.
2. Tighten the cable with zip ties.
3. Insert the connection cable of the EMF fixed leaf
into the EMF active leaf.
4. Insert the 24/48‑V‑DC connecting cable of the
RMZ or of the fire detection system by customers
into the EMF active leaf.
5 Start up
Only for GSR‑EMF XEA
5.1 Set the fixture point
ATTENTION
Risk of cable damage
While setting the fixture points cables might
be damaged.
• Pay attention not to jam the connecting
cables.
1. Feed the power supply (24 V/48 V DC).
2. Open the door leaves fitted with an EMF until it
clicks.
3. Unbolt the screws of the locking unit(s).
4. Open the door leaves to the desired opening angle
(GSR‑EMF 1 XEA: only fixed leaf; GSR‑EMF 1G
XEA: only active leaf).
5. Tighten the screws of the locking unit(s) again.
6. Place the door stop into the position of the fixture
points selected.
5.2 Set the release force
ATTENTION
Risk of damaging the slide rail system
Setting a release force too high may result
in damage to the door hinges and the
fastening elements of the door closing
system.
• Set the release force depending on the
door width and the selected size of the
closing contact.
• According to the DIN EN 1155 the release
force must not be less than 40 Nm at a
door opening angle of 90 and not more
than 120 Nm.
1. Set the release force.
2. Control the release force.
5.3 Mount the paneling
1. Attach the end caps.
2. Mount the paneling of the glide rail.
3. Measure the dimension X.
4. Shorten the middle paneling to the dimension
X‑14 mm.
5. Mount the middle paneling.
6. Attach the plastic shades.
5GSR XEA/GSR-EMF XEA 2017-10
dormakaba Mounting instruction
WN 059376 45532
Start up

5.4 Check the EMF
Only for GSR‑EMF XEA
The EMF can be released manually or by cutting of
the power supply.
5.4.1 Release EMF manually
1. Open and lock the door leaves which are fitted
with an EMF.
2. Pull on the locked door leaves.
‣ The door leaves are released and close. The
active leaf only closed when the fixed leaf is
closed.
5.4.2 Delete EMF electronically
1. Open and lock the door leaves which are fitted
with an EMF.
2. Cut off power supply (i.e. operation of the manual
release button, alarm release of the RMZ etc.).
‣ The door leaves are released and close. The
active leaf only closed when the fixed leaf is
closed.
6 Operating
Only for GSR‑EMF XEA
6.1 Open and lock door
1. Open door leaves to the fixture point.
‣ Active and fixed leaf remain standing after
letting go. (Only the active leaf remains
standing with the GSR‑EMF 1G XEA).
6.2 Close door
1. Firstly, press shut the fixed leaf, then the active
leaf against the resistance or press the optional
manual release button.
‣ The door leaves are released and close. The
active leaf only closed when the fixed leaf is
closed.
7 Dismounting,
recycling and
disposal
The dismounting takes place in reversed order of the
mounting and must be carried out by skilled staff.
The product must be disposed of environmentally
sound. Electro‑technical parts and batteries must not
be disposed of as household waste. Dispose of
electro‑technical parts and batteries in the arranged
acceptance and collection points.
6GSR XEA/GSR-EMF XEA 2017-10
dormakaba Mounting instruction
WN 059376 45532
Operating

7GSR XEA/GSR-EMF XEA 2017-10
dormakaba Mounting instruction
WN 059376 45532

dormakaba Deutschland GmbH
DORMA Platz 1 58256 Ennepetal Germany T: [phone] F: [phone] www.dormakaba.com
Translation of the original manual, subject to change without notice