Dräger Isolette 8000 plus User manual

How to clean the
Dräger Isolette 8000 / 8000 plus
91 08 127 | 19.12-1 | HQ | CS | Subject to modications | © 2019 Drägerwerk AG & Co. KGaA
Please complete all cleaning practices according to your hospital’s guidelines.
This document is for information purposes only. Refer to the instructions for use (User
Manual) of the device for full disassembly, cleaning and disinfecting instructions.
Only use disinfectants as listed in the instructions for use (User Manual).
Make sure no liquid penetrates into the device.
Allow sucient time for device to cool down before Reprocessing.
Clean with Disinfection Wipes (and machine wash where appropriate).
Please turn the page for assembly and disassembly instructions.
Ensure all surfaces are dry before using for therapy.
Perform Operational Checkout Procedure to make sure device operates correctly.
Prerequisites: There is no patient in the device.
Manufacturer:
Draeger Medical Systems, Inc.
3135 Quarry Road
Telford, PA 18969-1042, USA
1. Follow Manufacturer’s recommendations for dilution
(if appropriate), contact time, and all safety recommendations.
2. On appropriate surfaces specied in the User Manual (IfU)
Clean using an approved disinfecting agent. Do not spray on
surface of device, rather, on a cleaning wipe. Do not spray in the
impeller fan area.
3. After the appropriate contact time, wipe disinfectant using
a clean towel and water to remove residue.
4. Wipe dry on hood surface and other areas to prevent pooling
and/or smear marks.
5. Inspect all reprocessed components for damage or cracks
before reassembly.

!
!

PDF-9237 | 19.08-1 | AW | LE | Subject to modications | © 2019 Drägerwerk AG & Co. KGaA
Remove Gaskets
I n s t a l l G a s k e t s
3
21
Remove sleeves from ring
Install iris port sleeves
5
19
Remove sensor module
Install sensor module,
connect sensor module
cable to upper shell
6
18
Switch o device
Switch on device
1
23
Disconnect power plug
Reconnect power plug
2
22
Remove grommets
Install grommets
4
20
Slowly raise hood
Close hood
7
17
Remove mattress
Install mattress
8
16
Lift scale from bed
Install scale
9
15
Remove x-ray tray
Install x-ray tray
10
14
Remove bed
Install bed
11
13
Remove t-bars
I n s t a l l t - b a r s
12
12
Disassembly
Remove impeller cover
Install impeller cover
15
9
Let Device Cool
16
Remove reservoir
Install reservoir
14
10
Remove upper cover
Install upper cover
13
11
Careful: Collection bottle could contain patient uids
When the device has
cooled, remove heater
radiator
When the device
has cooled, install
heater radiator
16
7
If equipped, remove clamp
and pull the impeller from
the motor shaft
Install the impeller on the
motor shaft. If equipped,
install clamp
17
Remove the clamp from
thecondensation manage-
ment hose, discard
Install the clamp on
the condensation
management hose
19
5
Remove plug by
turning 90 °
Install plug by
turning 90 °
20
4
Slide the reservoir assembly
out from the front of the
incubator shell
Slide the reservoir assembly
in the front of the incubator
shell
21
3
Disassemble the reservoir
(pull latch at top, remove side
latches, remove cover)
Reassemble the reservoir
(push latch at top, latch side, install
cover)
22
7
Remove and replace the
Air Inlet Filter
Replace Air Inlet Filter &
install cover
23
1
2
Careful: The heater could
be hot enough to cause
burns. Avoid removing our
touching heater until de-
vice has been switched o
for at least 45 minutes
Careful: The water in the humidier chamber could be hot enough to
cause burns. Use caution when handling the reservoir.
Assembly
Reconnect the conden-
sation bottle to the conden-
sation management hose
6
Disconnect the condensa-
tion bottle from the conden-
sation management hose
18
8