Dräger Oxylog 2000 plus User manual

The Oxylog 2000 plus Pocket Guide is not a replacement
or substitute for the Instructions for Use. Any use of the
device requires full understanding and strict observation
of the Instructions for Use. The user must be familiar with
the device according to the national and local laws and
recommendations. There will be no exchange of the
Pocket Guide when the product is updated/upgraded.
Oxylog®2000 plus Pocket Gu de
Software version 1.n

3
Front panel with all options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7
Side view, right / Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
Preparat on
Breathing systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Assemble the reusable hose system . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connect the reusable hose system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Connect the disposable hose system . . . . . . . . . . . . . . . . . . . . . . . . . . .13
When using a bacterial filter or HME . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Connecting the power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Internal supply with rechargeable battery . . . . . . . . . . . . . . . . . . . . . . . . .15
Charging the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Indication of battery capacity / battery operation . . . . . . . . . . . . . . . . . .17
External power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-19
Connecting the gas supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Supply from a piped medical gas system . . . . . . . . . . . . . . . . . . . . . . . . .21
Index

4
Index
Determining the approximate pneumatic
operating time for the Oxylog® 2000 plus . . . . . . . . . . . . . . . . . . . . .22-23
Operat on / Sett ngs
Starting operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Perform device check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Ventilation controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Preparing ventilation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Available ventilation modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
VC-CMV / VC-AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Trigger (VC-AC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
VC-SIMV (optional PS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-33
SpnCPAP (optional PS) (optional NIV) . . . . . . . . . . . . . . . . . . . . . . . . . .34
SpnCPAP (Apnea Ventilation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
NIV – Non-Invasive Ventilation (optional) . . . . . . . . . . . . . . . . . . . . . . . . .36
Display operating controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

5
Alarms and Measured Values
In the event of an alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Setting alarm limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Displaying other measured values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Trouble Shoot ng
Alarm - Cause - Remedy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Messages in the alarm window . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42-48
Error messages during the device check . . . . . . . . . . . . . . . . . . . . . . . .49
Messages in the information window . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Index

6
The Oxylog 2000 plus Pocket Guide is not a replacement or substitute for the Instructions for Use.
Any use of the device requires full understanding and strict observation of the Instructions for Use.
Front panel with all options

7
AScreen with screen pages for the specific application
BKey Alarms for setting and displaying alarm
limits
CKey Sett ngs for setting other ventilation
parameters on the screen
DKey for ventilation mode VC-CMV / VC-AC
EKey for ventilation mode VC-SIMV (PS)*
FKey for ventilation mode SpnCPAP (PS)*
GRed and yellow lights (LEDs) as alarm indicators
HKey to suppress the audible alarm for 2minutes
IKey Alarm Reset for acknowledging alarm messages
JStart / Standby key
* Pressure Support and Non-Invasive Ventilation are optional features.
KDisplay symbols for the power supply
Charge status of the internal battery
Mains power supply connected
LCentral rotary knob for making selections /
settings and for confirming these
MControl knob for setting O2AirMix or 100% O2F O2
NControl knob for setting the maximum inspiratory
pressure Pmax
OControl knob for setting the ventilation respiratory
rate RR
PControl knob for setting the tidal volume VT
QKey Values to select the displayed measured
values
RKey Values to select the displayed measured
MVe or VTe values
Front panel with all options

A
B
C
D
E
F
G
Side view, right
AEmergency air intake
BScrew to secure the battery compartment cover
CConnectors for flow measuring hoses
DConnectors for ventilation hose
EConnector for medical gas hose
FSocket for DC supply
GWindow for Infrared Data Association (IrDA) interface
8

9
AFilter cartridge for intake of ambient air
BRating plate
A
B
Rear view

10
Preparation
Breathing Systems
Reusable hose system
ABreathing valve
BVentilation hose
CFlow and pressure measuring hoses
DAngled connector
EFlow sensor
D sposable hose system
ABreathing valve
BVentilation hose
CFlow and pressure measuring hoses
DFlow sensor
EAngled connector
A
B
E
C
D
A
B
C
D
E
The Oxylog 2000 plus Pocket Guide is not a replacement or substitute for the Instructions for Use.
Any use of the device requires full understanding and strict observation of the Instructions for Use.

11
Preparation
1Place the diaphragm (B) in the breathing valve. Ensure that it is
inserted correctly.
2Fit the cover (A) and turn it approximately 90° clockwise to secure
into position.
3Push the flow sensor (C) into breathing valve.
Note the preferred position as indicated by the groove.
4Connect the angled connector (D) to the flow sensor.
A
B
C
D
Assemble the reusable hose system
Please do not touch
the rubber disk
in the housing!

12
Preparation
Connect the reusable hose system
1Connect the ventilation hose (A) to the breathing valve.
2Connect the flow measuring hoses (B) to the nozzles
on the flow sensor. Note the different diameters.
3Connect the flow measuring (C) hoses to the Oxylog 2000 plus.
4Connect the ventilation hose (D) to the gas outlet on the
Oxylog 2000 plus.
A
B
B
D
C

13
Preparation
1Connect the blue flow measuring hose (B) to the blue gas connector.
2Connect the transparent flow measuring hose (A) to the other
gas connector.
3Connect the ventilation hose (C) to the gas outlet on the
Oxylog 2000 plus.
When chang ng the vent lat on hose system
If the reusable ventilation hose system is to be used instead of a
disposable hose system or vice versa:
1Have the nozzles on the device changed by trained service specialists.
2Reconfigure the device accordingly.
AB
C
Connect the disposable hose system

14
Preparation
Connect the bacterial filter or HME to the angled connector.
When using a bacterial filter or HME
Bacterial filter or HME

15
Preparation
Connecting the power supply
The Oxylog 2000 plus is designed to operate on power supplies with
different voltages:
•DC voltage from the on-board power supply:
°Via DC/DC converter
°With AC/DC power pack
•With rechargeable battery (specified Smart Battery)
Internal supply with rechargeable battery
Install ng the battery
1Insert a fully charged battery into the battery compartment (A).
2Attach the connector at the bottom.
3Turn the cover upwards (B).
4Tighten the screw (C).
Check ng the charge of the battery
Press the button on the rechargeable battery.
The charge status is indicated as a percentage by LEDs.
A
B
C

16
Preparation
1The green lamp (B ) lights up when the battery is actively
charging.
2A three colored indicator (A) lights up to show the current
charge status of the internal battery:
• Green: when the battery has been fully charged.
• Yellow: while the battery is being charged.
• Red: if a battery has not been inserted or a technical
failure occurred.
• Indicators (A) and (B) remain off while the ventilator is being
operated from the internal battery.
• Additional alarms can draw attention to the remaining operating
time of the battery.
• When operated via the rechargeable battery, the brightness of
the ventilator screen is reduced in order to save power.
• The screen brightness is automatically increased to maximum
for one minute while settings are being made.
Oxylog 2000plus
B
A
Charging the battery

17
Preparation
Indication of battery capacity / battery operation
The remaining capacity of the battery is indicated by
Oxylog 2000 plus in 25% increments in the lower right
section of the information window when power is ON.
The capacity indication is overwritten if higher priority messages
are activated.
Example: 75% charge

18
Preparation
External power supply from ma ns power (AC/DC power pack)
1Connect the mains plug (A) to the mains outlet.
2Connect the DC plug (B) to the DC connector on the
Oxylog 2000 plus.
3When the Oxylog 2000 plus is connected to an external supply, the
indicator (C) lights up.
O xylog 2000 plus
A
B
C
External power supply

19
Preparation
Oxylog 2000 plus
12 V DC
24 V DC
28 V DC
C
B
A
External power supply w th DC/DC converter
The DC/DC converter must be used to connect the Oxylog 2000 plus
to permanently installed onboard battery systems of different voltages
(12 V, 24 V, 28 V DC).
1Plug the large connector (A) of the DC/DC converter into
the on-board supply.
2Plug the small connector (B) into the DC connector of the
Oxylog 2000 plus.
3When the Oxylog 2000 plus is connected to an external supply,
the indicator (C) lights up.
External power supply

20
Preparation
Connecting the gas supply from an O2cylinder
Connect ng the gas supply supply from an O2cyl nder
1Use a full O2cylinder.
2Connect the pressure reducer (270 to 600 kPa delivery pressure,
500 kPa nominal pressure) to the O2cylinder.
3Connect the O2medical gas hose (A) to the Oxylog 2000 plus.
4Connect the O2medical gas hose to the pressure reducer (B).
5Rotate the cylinder valve (C) slowly and open fully.
O2
A
B
C