Dragonfly 92-145 User manual

INSTALLATION MANUAL
92-145" Fixed Projection Screens
IMPORTANT: BEFORE YOU BEGIN
• To avoid staining or scratching the screen, wash your hands and clean the work
area before starting.
• Do not use knives or sharp objects to open the packing boxes.
• To avoid a serious fire hazard, DO NOT install the screen over an electrical outlet
or switch.

DF-SL-92-145 Installation Manual
© 2016 Dragonfly
Dragonfly Fixed Screen Assembly Instructions
Step 1. Unpack the Screen
A. Lay out all the parts on a clean, flat surface.
B. To avoid stains or damage, do not unpack the screen material at this time.
Package Contents
Snap Lugs
(see below, +2 extra)
5x40mm Phillips
Head Screws (8)
Concrete
Anchors (8)
Tethered Mounting
Bracket (1)
Screen Material
(1)
L Bracket
Assembly (4)
Screen Frame
(2 short, 2 long)
Tensioning Rod
(2 short, 2 long)
Step 2. Install the Snap Lugs in the Frame
The snap lugs hold the screen material in place on the frame. Slide one lug into place at each arrow decal on
the frame. Two spare lugs are included; do not install them unless needed.
Screen Size Lugs Used Screen Size Lugs Used
84" 22 110" 28
92" 24 120" 30
100" 28 133" 34
106" 28 145" 38
Step 3. Assemble the Frame
A carpenter’s square is very helpful for this step.
A. Place all of the frame tubes face down on a flat, clean work surface and line up the ends to form the shape
of the finished screen.
B. Loosen the screws on the L-bracket assemblies, then carefully slip the brackets into the aluminum frame
channel.
C. Work around the frame several times, using the square to align the frame corners and tightening the
screws a little each time.
L-Bracket Top Frame
Side Frame

DF-SL-92-145 Installation Manual
Step 4. Attach the Screen Material
A. Wash your hands and clean the work area to avoid staining the screen material.
B. Unpack the screen material and tension rods. Unroll the screen material and lay it flat, with the seam side
up, across the back of the screen frame.
C. Push the shorter tension rods through the edges of the
screen material, making sure not to damage the material.
Do not insert the longer rods yet.
D. Attach snaps 1-4 in order. The rods must be positioned
behind the snaps to provide the correct tension.
E. Insert the longer tension rods.
F. Attach snaps 5-8 in order.
G. Working from the outside towards the center:
i. Attach the remaining snaps on the short sides,
9 and 10 last.
ii. Attach the remaining snaps on the long sides, 11 and 12
last.
11
12
9 10
7
3
4
85
1
2
6
Installation Tips
Take your time and avoid breaking lugs. If you can’t get the
screen attached with the rod behind all of the snaps, stop
and let the material stretch for a few minutes, then continue.
Let the screen settle after assembly. Small fold lines or
wrinkles from the packaging may exist for a few hours.
Optional for UAW Screens: Anti-Reflection Material
All Ultra Acoustiweave models include a precut sheet of black backing material to reduce reflections from
surfaces behind the screen. The backing is also acoustically transparent, so sound quality is not aected by
it.
To use the backing, either attach it to the rear of the assembled film screen before hanging, or hang it from
the wall behind the screen after fastening the mounting brackets to the wall.
Tension Rod
161212-1500

Step 5. Hang the Mounting Bracket
A level, measuring tape, and drill are very helpful for this step.
A. Position the screen and temporarily mark the edge of
the top and sides on the wall. Mark the location for the
top of the mounting bracket 1/2" down from the top of
the screen, centered between the sides.
B. Position and level the top bracket, then mark the wall
for three screw locations spread as far apart as possible.
For drywall installation, use a stud finder to ensure that
the screws hit the wood studs.
C. Prepare the wall for the screws/anchors:
i. Drywall studs: 5/32" drill for pilot holes
ii. Masonry: 1/4" masonry drill bit for anchors
D. Install the anchors (if applicable), then hang the top
bracket using the included 5X40mm screws. Make sure
the tethers remain untwisted.
E. Let the bottom bracket hang freely from the tethers. Pull down enough to eliminate any slack and mark
the screw locations, then fasten the bottom bracket in the same fashion as the top.
Step 6. Hang the Screen on the Bracket
Hook the screen frame onto the top bracket, then push the bottom of the screen
into the security clips until they snap into place.
If you have trouble, measure from the top to the bottom of the brackets; the
dimension should match column F in the dimensions below.
To release the screen, push in the clips and carefully lift the bottom of screen up and
away from the wall.
Care and Cleaning
Clean the screen with a soft cloth using mild soap and water
only. DO NOT use harsh detergents, chemicals, distilled
spirits or petroleum-based chemicals to clean the screen.
Doing so may result in severe damage to the screen or the
frame coating.
Use a household vacuum cleaner with a brush or furniture
cleaning attachment to clean the felt frame material. Avoid
using excessive amounts of water on the felt.
Dimensions
Size (A) B C D E F*
92" 45.08'' 80.2'' 51.42'' 86.54'' 51.3’’
100" 49.02'' 87.17'' 55.35'' 93.5'' 55.24’’
106" 51.93'' 92.36'' 58.27'' 98.7'' 58.15’’
110" 53.9'' 95.87'' 60.24'' 102.2'' 60.12’’
120" 58.82'' 104.57'' 65.16'' 110.9'' 65’’
133" 65.2" 116" 71.54" 122.24" 71.38"
145" 71.1" 126.37" 77.3" 132.57" 77.14"
*-Top of upper to bottom of lower mounting bracket.
Top Bracket
Bottom Bracket
Security Clips
1/2" below top
of screen
UP
Drywall Masonry
E
D
BA
F
C