Draper IntelliFlex C156.282 User manual

Internal Sun Sensor - Part # C156.282
IntelliFle
INSTRUCTIONS
INSTALLATION & PROGRAMMING
Section 1 - Mounting the Internal Sun Sensor
Section 1.1 – Mounting with Sensor Stand
1. Determine mounting location of Internal Sun Sensor.
2. Remove base from the bottom of the sensor stand
by rotating the base 90° (see Fig. 1A). Secure the base
to the window sill using the provided hardware.
3. Line up mounting hole on the bottom of the sensor
stand with central mounting peg on the base.
4. Once sensor stand is over the mounting peg, rotate
stand 90°. Sensor stand is now sucure.
5. Thread the data cable (Cat5 or better) through the back
of the stand (see Fig.1B).
6. Remove the back cover from the Internal Sun Sensor
and connect the data cable. Replace the back cover
and attach the Internal Sun Sensor to the stand.
Section 1.2 – Mounting with Self Adhesive
1. Secure the Internal Sun Sensor directly to the window glass
with the provided clear circular double-sided adhesive (see Fig. 2).
2. Remove the back cover from the Internal Sun Sensor
and connect the data cable. Replace the back cover.
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
© 2019 All Rights Reserved | FORM: IO_InternalSunSensor_Inst19
Mounting Holes
Figure 1-A FRONT VIEWTOP VIEW
Figure 1-B
Window Sill
90°
to
Sensor/Schedule
Interface
Internal
Sun Sensor
Part#: C156.282
Remove
Back Cover
Connect
Data Cable
(Cat5 or better)
Window Sill
Figure 2
Data Cable
to Sensor
Interface
Internal
Sun Sensor
Part#: C156.282
Remove
Back Cover
Connect
Data Cable

Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
© 2019 All Rights Reserved | FORM: IO_InternalSunSensor_Inst19
Section 4 - Sensor / Schedule Interface Main Screen
Main screen shows the current date and time, as well as readings for each configured sensor.
When the Internal Sun Sensor is plugged into the Sensor/Schedule Interface (SSI), it will
automatically be configured and the current reading will be displayed (see Fig. 5).
The default settings for the sensor control are:
• Profile – Automatic Control (Shades retract when cloudy and extend when sunny)
• Threshold – 50%
• Cloudy Delay – 15 min
• Sunny Delay – 5 sec
• Group – Master*
* If 2 sensors are plugged into the same SSI, they will be added to the same sensor group (Master).
In this case, the highest reading between the two sensors at any time will be used to control the shades.
All of these settings can be adjusted using the Configuration Menu on the Sensor/Schedule Interface.
Please refer to the Sensor/Schedule Interface (SSI) instructions for specific directions.
Section 3 - Connecting Sensor to Sensor / Schedule Interface
TOP
21
Interior Brightness Sensor Ports
The Sensor 1 and Sensor 2 ports (see Fig. 4) are used to connect to the Draper Internal Sun Sensor (C156.282).
Figure 4
 
 




Figure 5
Section 2 - Adjusting Light Sensitivity (kLux)
1. Remove the back cover from the Internal Sun
Sensor to expose the sensitivity dial (see Fig. 3).
2. Set the sensor to the desired sensitivity.
Replace the back cover and return the sensor
to it’s proper location in the window.
Figure 3
Internal
Sun Sensor
Part#: C156.282
Remove
Back Cover
10kLux
OFF
100kLux
1kLux
Least Sensetive
Most Sensetive
Moderately Sensetive