Dream On Me 597 User manual

1
ASSEMBLY INSTRUCTIONS
STYLE NO: 597
d
efh
b
ac
AConnection Panel 1
REF. PART NAME QUANTITY
B Left Panel 1
C Right Panel 1
D Front Top Rail 1
E Front Middle Rail 1
a 2-1/8” bolt 12
b barrel nut 12
c cams 15
d cam bolts 15
e 1” screw 45
f 1-3/5” wood dowel 10
h knob 10
i 1-1/8” screw 10
k allen wrench 1
n tip over restraint 2
H Back MIiddle Rail 1
I Back Bottom Rail 1
J Back Panel 2
F Front Bottom Rail 1
G Back Top Rail 1
DR1 Drawer Front Panel 5
(one is different from others)
DR2 Drawer Side Panel 10
DR3 Drawer Back Panel 5
DR4 Drawer Bottom Panel 5
DR5 Drawer Support Rail 5
WARNING
i
A
B
C
D
E
F
G
I
J
DR3 DR2.2
DR5
DR4
DR1
DR2.1
k
n
H
J
Read all instructions before assembling.Save
instructions for future use.Carefully remove and lay
out all parts.Familiarize yourself with all diagrams to
facilitate the assembly of your product.Check parts
and the enclosed hardware bag with the hardware
parts list to be sure all are included and quantities
are correct.Destroy cardboard and plastic bags
immediately.
Attention:In order to properly assemble the chest,
follow the assembly instructions carefully.Failure to
assemble in the manner recommended could make
the chest hazardous.
Warning:Never use this product if there are any loose
or missing fasteners,loose joints,broken parts,or torn
mesh/fabric.check before assembly and periodically
during use.Contact Dream On Me.for replacement
parts and instructional literature if needed.
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE
Dream On Me Inc.
1532 S Washington Ave
Piscataway Township
NJ 08854
TEL: [phone]
Customer Care: [phone]

2
Use allen wrench (k) to connect bolts.
Connect front top rail (D),front middle
rail(E),front bottom rail (F),back top
rail (G),back bottom rail (I) to right
panel (C) by using 1-3/5” wood doewl
(f),barrel nut (b) and 2-1/8” bolt (a)
Connect back middle rail (H) to right
panel (C) by using 2-1/8” bolt (a) and
barrel nut(b).
Then insert the back panel (J) into
the grooves of part (G),(H),(I).
Assemble left panel (B) to the assembled
parts use the same way as shown in
STEP 1.
STEP 1
STEP 2

3
Connect connection panel (A) to left & right
panel (B&C) and front & back top rail (D&G)
by using cams (c) and cam bolts (d).
Tighten all by phillips-head screwdriver.
STEP 3
STEP 4
PHILLIPS--HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ----NOT INCLUDE
Connect drawer side panel (DR2) to front
panel (DR1) by using 1” screw (e).
Connect drawer support rail (DR5) to
drawer front panel (DR1) by using cams
(c) and cam bolts (d).
MAKE SURE the grooves line up and face
inside.
LOCK cams (c) into drawer support rail
(DR5) by turning them.
DR2.2
DR2.1
DR5
DR1
e
e
e
e
c
d

Slide drawer bottom panel (DR4)
into grooves of drawer front panel
(DR1) and side panel (DR2).
STEP 5
STEP 6
Connect drawer back panel (DR3) to drawer
side panel (DR2) and drawer support rail
(DR5) by using 1” screw (e).
ASSEMBLE the rest of drawers by repeating
STEP 6,7,8.
DR2.1
DR2.2
DR1
DR4
e
e
DR2.1
DR2.2 DR3
DR1
DR4
e
e
e
4

Connect the knob (h) to front panel (DR1)
by using 1-1/8” screw (i).
STEP 7
STEP 8
Slide the drawers into rails on left&right panel (B&C).
NOTE: PLEASE PUT THE DRAWER WITH CLEAN STICKER AS THE TOP ONE.
DR1
h
ih
i
5

FURNITURE TIPPING DETERRENT HARDWARE
n
HOW TO LOCK
Tipping furniture may injure young children. Use of this tipping restraint hardware is highly
recommended.
When properly instated this hardware could provide protection against the unexpected
tipping of furniture due to improper use.
This hardware is only a deterrent.Adult supervision is the only proper deterrent to prevent
improper use of any potentially hazardous product.
1. Attach one of the mounting brackets securely to the back top edge of the furniture using
the short screw.
2. Find the stud in the wall and mark the location on the wall for mounting the second
bracket using a 2” wood screw approximately 2” below the bracket mounted to the edge
of the furniture.
3. If a stud cannot be found,purchase a “Hollow-Wall Anchor Bolt” and attach the second
bracket to the wall using that bolt.Make sure to follow all instructions by the manufacturer.
4. Place the furniture so the bracket on the back edge is in line with the bracket on the wall.
5. Lace an end of the nylon restraint strap down through each bracket.Bring both ends
together and slide the beaded end of the strap through the key hole shaped slot in the
other end tightly.Pull down on the beaded end until it snaps locks into the keyhole.
6. Check to make sure the strap is securely laced and locked to the brackets.
WARNING
6