Dream On Me 596 User manual

1
STYLE NO: 596
REF. PART NAME QUANTITY
Read all instructions before assembling.Save
instructions for future use.Carefully remove and lay
out all parts.Familiarize yourself with all diagrams to
facilitate the assembly of your product.Check parts
and the enclosed hardware bag with the hardware
parts list to be sure all are included and quantities
are correct.Destroy cardboard and plastic bags
immediately.
Attention:In order to properly assemble the chest,
follow the assembly instructions carefully.Failure to
assemble in the manner recommended could make
the chest hazardous.
Warning:Never use this product if there are any loose
or missing fasteners,loose joints,broken parts,or torn
mesh/fabric.check before assembly and periodically
during use.Contact Dream On Me.for replacement
parts and instructional literature if needed.
B
A
C
Top Panel 1
1
1
Front Top Rail
1
2
D
EFront Middle Rail
Back Bottom Rail
1
F
1
G
3
H
Left Side Panel
Right Side Panel
2
J Back Panel
1DR1 Drawer Front Panel(Small)
2DR2 Drawer Side Panel(Small)
1
DR3 Drawer Back Panel(Small)
4DR4
4DR5
Drawer Bottom Panel
Drawer Support Rail
10
a2-3/8” bolt
bbarrel nut 10
16
c
d
cams
cam bolts 16
20
e
f1-1/2” screw
1-5/8” wood dowel
36
g1-3/8” screw 6
hknob 8
i1” screw 8
jallen wrench (for f)
allen wrench (for a)
1
k1
1
30
m
n
o
plastic-strip
screw (for back panel)
tip over restraint
3
Drawer Front Panel(Big)
6
Drawer Side Panel(Big)
3
Drawer Back Panel(Big)
1
Front Bottom Rail
Back Top Rail
a b c d e
fgh i
jk m n o
A
B
C
D
E
E
E
G
H
H
J
J
DR1
DR3
DR4
F
Dream On Me Inc.
1532 S Washington Ave
Piscataway Township
NJ 08854
TEL: [phone]
Customer Care: [phone]

2
Use allen wrench (k) to connect
bolts.
Connect front top rail (D),front
bottom rail (F),back top rail (G)
and back bottom rail (H) to right
side panel (C) by using 1-5/8”
wood dowel (e),barrel nut (b)
and 2-3/8” bolt (a).
Connect front middle rail (E) to
right side panel (C) by using
1-5/8” wood dowel (e),cams (c)
and cam bolts (d).
Assemble left side panel (B) to the assembled
parts use the same way as shown in STEP 1.
STEP 1
STEP 2
B
b
b
b
e
e
e
e
e
e
e
d

3
STEP 3
Connect top panel (A) to left & right side panel
(B&C) by using 1-5/8” wood dowel (e),cams (c)
and cam bolts (d).
Connect front top rail (D) and back top rail (G)
to top panel (A) by using 1-3/8” screw (g).
Tighten all by phillips-head screwdriver.
STEP 4
Use plastic-strip (m) to connect back panel (J) .
A
J
J
m
B
C
D
G
g
g
g
g
g
g
e
e
ee
PHILLIPS--HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ----NOT INCLUDE

4
STEP 5
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE
Connect the assembled parts of STEP 4 to
the back of the chest by using screw (n).
Tighten all by phillips-head screwdriver.
Connect drawer side panel (DR2) to drawer front
panel (DR1) by using 1-1/2” screw (f).
Connect drawer support rail (DR5) to drawer
front panel (DR1) by using cams (c) and cam
bolts (d).
MAKE SURE the grooves line up and face inside.
LOCK cams (c) into drawer support rail (DR5) by
turning them.
USE allen wrench (j) to tighten 1-1/2” screw (f).
STEP 6
Assemble the Drawer-big.
DR1
c
d
n
n
n
n

5
Slide drawer bottom panel (DR4) into grooves of drawer front panel (DR1)
and drawer side panel (DR2) .
Connect drawer back panel (DR3) to drawer side
panel (DR2) and drawer support rail (DR5) by
using 1-1/2” screw (f).
TIGHTEN all by allen wrench (j).
ASSEMBLE the rest of drawers by repeating
STEP 6,7,8.
STEP 7
STEP 8
DR4
DR4
j
DR3
DR1

6
Connect the knob (h) to drawer front panel (DR1) by using 1” screw (i).
Slide the drawers into rails on left&right panel (B&C).
NOTE: PLEASE PUT THE DRAWER WITH CLEAN STICKER AS THE TOP ONE.
STEP 9
STEP 10
DR1
i
i
h
h

7
Tipping furniture may injure young children. Use of this tipping restraint hardware is highly
recommended.
When properly instated this hardware could provide protection against the unexpected
tipping of furniture due to improper use.
WARNING
HOW TO LOCK
This hardware is only a deterrent.Adult supervision is the only proper deterrent to prevent
improper use of any potentially hazardous product.
1. Attach one of the mounting brackets securely to the back top edge of the furniture using
the short screw.
2. Find the stud in the wall and mark the location on the wall for mounting the second
bracket using a 2” wood screw approximately 2” below the bracket mounted tothe edge
of the furniture.
3. If a stud cannot be found,purchase a “Hollow-Wall Anchor Bolt” and attach the second
bracket to the wall using that bolt.Make sure to follow all instructions by the manufacturer.
4. Place the furniture so the bracket on the back edge is in line with the bracket on the wall.
5. Lace an end of the nylon restraint strap down through each bracket.Bring both ends
together and slide the beaded end of the strap through the key hole shaped slot in the
other end tightly.Pull down on the beaded end until it snaps locks into the keyhole.
6. Check to make sure the strap is securely laced and locked tothe brackets.
0
FURNITURE TIPPING DETERRENT HARDWARE
MADE IN CHINA