Dream On Me 628 User manual

4. HEAD BOARD(RIGHT)
3. HEAD BOARD(LEFT)
CRIB COMPONENTS QTY
CONNECTION HARDWARE
5. THE STABILIZER BAR
6. MATTRESS SUPPORT
1. DROP SIDE
2.STATIONARY SIDE
7. GUARD RALL
2
CRIB COMPONENTS
QTY.,
3'
4PCS
3/4' 4PCS
2 1/8' 2PCS
3 • 4PCS
1PCS
2PCS
1
1 1. DROP SIDE
2. STATIONARY SIDE
1 3. HEAD BOARD(LEFT)
1 4. HEAD BOARD(RIGHT)
1 5. THE STABILIZER BAR
1 6. MATTRESS SUPPORT
1 7. GUARD RALL
(FOR GUARDRALL
L
.,..
(ALLEN WARENCH)
0:75;5
(WOODPIN)
4PCS
(CASTERS)

NE
Locate the metal spring with tabs. Be sure the smooth side of metal
spring is paced upward. Position the tabs of meral spring to mount
to the selected position onto the legs . Inlert the bolts
(B) , through
the tabs and into thread insets onto the legs , then tighten securely
with Allen Wrench.
3TEP 1
Attach the stationary side to the head board by
using bolts and barrel nut(A). Then attach
the stabilizer bar to the head board by
using wood dowels and bolts and
barrel nuts(C),
A
A
THE BOTTOM STRETCHER
STEP 2
3

Attach the drop side to the head board by sliding the plastic parts on the
drop side rails to the guide on the headboard legs.
STEP 3
STEP 4
Insert the four.casters and tighten all bolts. Inspect
the crib to make sure it is assembled correctly and
all bolts are light.
4

STEP 5
To lower the drop side
lift by holding the top of the rail in the center . Lift
until the dropside reaches it's hightest point .Using
your shin or knee ,press the bottom center of
dropside inward,then lower it.
To raise the drop side
li ft the dropside in the center when the dropside is
at it's hightest point,lower it a little and it will lock
into place.
Always verify that both ends of the dropside are
locked in the raised position whenever a child is
place in the crib . Only lower the side when
removing the child from the crib.
STEP 6
CONVER THE CRIB INTO TODDLIER BED
1.Remove the drop side and the plastic guides on the headboard legs.
2.Install the guard rail as toddler bed by using bolts and nuts(D).

ITEM NO.: #628
DREAM ON ME INC.
219 36th Street
Brooklyn,ny 11232
T:718-768-5500
ASSEMBLY INSTRUCTIONS
WARNING:
FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS
INURY OR DEATH.
READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB.KEEP INSTRUCTIONGS FOR FUTURE USE.
CHECK FASTENERS PERIODICALLY FOR TIGHTNESS.DO NOT OVER TIGHTEN,THIS MAY CAUSE
DISTORTION OR BREAKAGE.
BEFORE EACH USAGE OR ASSEMBLY,INSPECTCRIB FOR DAMAGED HARDWARE,LOOSE JOINTS,
MISSING PARTS OR SHARP EDGES,D0 NOT USE CRIB IF ANY PARTS ARE MISSING OR BROKEN.
ASK YOUR DEALER OR WRITE TO DREAM ON ME FOR REPLACEMENT PARTS.
WHEN CHILD IS AB LE TO CLIMB OUT OR REACHES THE HEIGHT OF 35 INCHES,THE CRIB SHALL
NO LONGER BE USED.
DO NOT PLACE CRIB NEAR A WINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY STRAGLE A CHILE.
REPLACE TEETHING RAILS IF DAMAGED OR LOOSE.
NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVER.THEY CAN CAUSE
SUFFOCATION.
IF REFINISHING,USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN'S PRODUCTS.
ANY
MATTRSS USED IN THIS CRIB MUST BE AT LEAST 27-1/4"BY51-5/8"WITH A THICKNESS NOT
EXCEEDING 6"
DAILY
CHECK THAT THE CRIB SPRING IS SECURELY ATTACHED TO EACH OF THE HANGER BRACKETS.
DO NOT TIE DECORATIONS OR TOYS BETWEEN THE CRIB SIDE RALLS, AS CHILE
MAY
BE CAUGHT OR
STRANGLED.