Dream On Me 598 User manual

1
ASSEMBLY INSTRUCTIONS
STYLE NO: 598
d
ef
b
ac
AConnection Panel 1
REF. PART NAME QUANTITY
B Left Panel 1
C Right Panel 1
D Front Top Rail 1
E Front Bottom Rail 1
a 3 ” bolt 12
b barrel nut 12
c cams 5
d cam bolts 5
e 1” screw 45
f 1-3/5” wood dowel 6
g knob 10
h 1” screw 10
i allen wrench 1
j tip over restraint 2
H
Back Bottom Rail 1
Back Panel 2
J Back Middle Rail 1
F
G
Back Top Rail 1
DR1 Front panel 5
DR2 Side panel 10
DR3 Back panel 5
DR4 Bottom panel 5
DR5 Bottom support panel 5
WARNING
D
E
F
G
J
DR3
DR2.2
DR5
DR4
DR1
DR2.1
gh
i
H
A
B
C
H
Read all instructions before assembling.Save
instructions for future use.Carefully remove and lay
out all parts.Familiarize yourself with all diagrams to
facilitate the assembly of your product.Check parts
and the enclosed hardware bag with the hardware
parts list to be sure all are included and quantities
are correct.Destroy cardboard and plastic bags
immediately.
Attention: In order to properly assemble the chest,
follow the assembly instructions carefully.Failure to
assemble in the manner recommended could make
the chest hazardous.
Warning:Never use this product if there are any loose
or missing fasteners,loose joints,broken parts,or torn
mesh/fabric.check before assembly and periodically
during use.Contact Dream On Me.for replacement
parts and instructional literature if needed.
j
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE
Dream On Me Inc.
1532 S Washington Ave
Piscataway Township
NJ 08854
Customer Care: [phone]
Customer Care: [phone]

2
STEP 1
STEP 2
C
C
F
F
a
a
a
a
f
b
b
b
b
b
b
f
f
D
A
H
H
D
G
G
J
J
E
E
Use allen wrench (i) to connect bolts.
Connect front top rail (D),front bottom
rail (E), back top panel (F),back bottom
rail (G) and back middle rail (J) to right
panel (C) by using 3” bolt (a),barrel
nut (b) and 1-3/5” wood dowel (f).
Lay down the assembled parts on the floor.
Slide the connection panel (A) into the grooves
on back top panel (F) and front top rail (D).
Slide the back panel (H) into the grooves on
back top panel (F),back bottom rail (G)
and back middle rail (J).

3
STEP 3
STEP 4
Connect side panel (DR2) to front panel
(DR1) by using 1” screw (e) .
Connet bottom support panel (DR5) to
front panel (DR1) by using cams (c) and
cam bolts (d).
MAKE SURE the grooves line up and face
inside.
LOCK cams (c) into bottom support panel
(DR5) by turning them.
USE allen wrench (m) to tighten 1”
screw (e).
e
c
d
e
e
DR1
DR5
DR2.2
DR2.1
e
A
H
H
F
G
D
E
B
a
a
a
a
a
a
b
b
b
b
b
b
f
f
f
Assemble to the assembled
parts of STEP 2 use the same way as shown in STEP 1.
the left panel (B)

4
Slide bottom panel (DR4) painted side
up , into grooves of front panel (DR1)
and side panel (DR2) .
STEP 5
STEP 6
Connect back panel (DR3) to side panel (DR2)
and bottom support panel (DR5) by using
1” screw (e).
TIGHTEN all by allen wrench (m) .
ASSEMBLE the rest of drawers by repeating
STEP 4,5,6.
DR5
DR4
DR1
DR2.1
DR2.2
DR1
DR3
DR2.1
DR2.2
DR4
e
e
e
e
e

5
Connect the knob (g) to front panel (DR1)
by using 1” screw (h) .
STEP 7
STEP 8
Slide the drawers into rails on left&right panel (B&C) .
NOTE: PLEASE PUT THE DRAWER WITH CLEAN STICKER AS THE TOP ONE .
h
g
DR1

FURNITURE TIPPING DETERRENT HARDWARE
j
6
HOW TO LOCK
MADE IN CHINA
Tipping furniture may injure young children. Use of this tipping restraint hardware is highly
recommended.
When properly instated this hardware could provide protection against the unexpected
tipping of furniture due to improper use.
WARNING
This hardware is only a deterrent.Adult supervision is the only proper deterrent to prevent
improper use of any potentially hazardous product.
1. Attach one of the mounting brackets securely to the back top edge of the furniture using
the short screw.
2. Find the stud in the wall and mark the location on the wall for mounting the second
bracket using a 2” wood screw approximately 2” below the bracket mounted to the edge
of the furniture.
3. If a stud cannot be found,purchase a “Hollow-Wall Anchor Bolt” and attach the second
bracket to the wall using that bolt.Make sure to follow all instructions by the manufacturer.
4. Place the furniture so the bracket on the back edge is in line with the bracket on the wall.
5. Lace an end of the nylon restraint strap down through each bracket.Bring both ends
together and slide the beaded end of the strap through the key hole shaped slot in the
other end tightly.Pull down on the beaded end until it snaps locks into the keyhole.
6. Check to make sure the strap is securely laced and locked to the brackets.