Dream On Me TB8643 User manual

.
1
ITEM NO: TB8643
Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed please find simple step-by-step instructions to help
you quickly assemble your products.Before you begin we
recommend that you follow the steps below:
1.Please read the instructions toroughly.
2.Identify all parts and hardwares.
3.You will need the following tools:
Philips head screw driver
Flat head screw driver
Hammer
Do Not use Power Drills or Drivers
To protect your parts during assembly please place them on a
soft surface.
To clean surface use only water on a damp cloth.Do not use
window cleaners or cleaning abrasives as it will scratch the
surface and could damage the protective coating.
ASSEMBLY INSTRUCTION

2
WARNING !
· FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.
· READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS
FOR FUTURE USE.
· UPON COMPLETION OF ASSEMBLY, MAKE SURE ALL SCREWS,BOLTS AND
FASTENERS HAVE BEEN SECURELY TIGHTENED.
A FREQUENT AND PEDRIODICALLY CHECK SHOULD BE MADE TO CONFIRM ALL
THE SCREWS AND NUTS REMAIN TIGHT.
· NEVER USE THIS PRODUCT IF THERE ARE ANY LOOSE, MISSING FASTENERS,
LOOSE JOINTS,BROKEN PARTS, OR TORN MESH/FABRIC.CONTACT YOUR LOCAL
RETAILER FOR REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF
NEEDED.
· NEVER SUBSTITUTE PARTS, THE PRODUCT INCLUDING SIDE RAILS,MUST BE
FULLY ERECTED PRIOR TO USE.
· NEVER USE BED FOR INFANTS, THIS TODDLER BED IS NOT A SUBSITITUTE FOR A
CRIB,THE TODDLER BED IS USED FOR A CHILD BETWEEN THE AGE OF 15MONTHS
TO 5 YEARS WITH A MAXIMUM WEIGHT OF 50 POUNDS(22.7KG).
· NEVER USE PLASTIC SHIPPING BAGOR OTHER PLASTIC FILM AS A MATTRESS
COVERS NOT SOLD AND INTENDED FOR THAT PURPOSE,THEY CAN CAUSE
SUFFOCATION.
· CAUTION ENTRAPMENT HAZARD:TO AVOID DANGEROUS GAPS,ANY MATTRESS
USED IN THIS BED SHALL BE FULL SIZE CRIB MATTRESS AT LEAST 51-58IN
(1310MM) IN LENGTH, 27-1/4IN(690MM) IN WIDTH AND 4IN(100M) IN THICKNESS,OR
GREATER,BUT NOT EXCEED 5IN.
· NEVER USE A WATER MATTRESS WITH THIS TODDLER BED.
· WARNING STRANGULATION HAZARD:STRINGS CAN CAUSE STRANGULATION!
NEVER PLACE BED NEAR WINDOW WHERE CORDS FROM BLINDS OR DRAPES
MAY STRANGLE A CHILD.NEVER SUSPEND STRINGS OVER BED.
NEVER PLACE ITEMS WITH A STRING CORD,OR RIBBON,SUCH AS HOOD STRINGS,
PACIFIER CORDS AOUND A CHILS’S NECK.THESES ITEMS MAY CATCH ON BED
PARTS.
· WARNING: INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
OPENINGS IN AND BETWEEN BED PARTS CAN ENTRAP HEAD AND NECK OF A
SMALL CHILD. NEVER USE BED WITH CHILDREN UNDER 15MONTHS.ALWAYS
FOLLOW THE ASSEMBLY INSTRUCTIONS.
· TO REDUCE THE RISK OF SIDS,PEDIASTRICIANS RECOMMED HEALTHY INFANTS
BE PLACED ON THEIRE BACK TO SLEEP,OR ADVISED BY YOUR PHYSICIAN.
· DO NOT USE BED IF THE SPACE BETWEEN BED AND SOLID OBJECTS IS LESS
THAN 12IN(31CM), A CHILD COULD SLID INTO THE SPACE AND SUFFOCATE.
· IF REFINISHING,USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS.
TO WASH,CLEAN WITH MILD SOAP AND DAMP CLOTH.
TO STORE,PLEASE KEEP IN A COOL PLACE.
MADE IN CHINA

3
COMPONENT PARTS
(A) Headboard (1pc) (B) Footboard (1pc) (C1) Right Bed Rail (1pc)
(D1) Right Side Rail (1pc) (E) Cross Middle Bar (1pc)
(H1) Right Cross Bar (1pc)
(G) Drawer Front Panel
(1pc)
(K) Drawer Bottom Support Bar
(1pc)
(J) Drawer Middle Panel
(1pc)
(C2) Left Bed Rail (1pc)
C1
C2
(D2) Left Side Rail (1pc)
(H2) Left Cross Bar (1pc)
(I) Drawer Back Panel (1pc)
(L) Drawer Bottom Panels
(2pcs)
(F) Cross Bar (8pcs)
H1
H2
D1
D2

4
Connect Cross Middle Bar (E) to
the Side Bar (D1) using barrel
nut (c) and bolt (b) . Attach
Cross Bar (F) to Side Bar (D1) .
STEP 1
D1
E
F
F
F
F
FF
F
F
b
c
HARDWARE AND TOOL DIAGRAM
(a) Bolt 3’ (10pcs) (b) Bolt 2-1/5’ (2pcs) (c) Barrel nut (12pcs)
(d) Allen Wrench (1pc) (e) Bolt 1-3/5’ (4pcs) (f) Wood Dowel (2pcs)
(i) Wood Screw (1pc)
PHILLIPS-HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ---- NOT INCLUDE
（h）Cams 12 PCS
（g）Cam Bolts 12 PCS

5
Connect the other Side Bar (D2)
to the Cross Middle Bar (E) using
barrel nut (c) and bolt (b) .
Make sure Cross Bar (F) are
connected to the hole on
Side Bar (D2) .
STEP 2
Attach Side Bar (D) to Headboard (A)
using barrel nuts (c) and bolts (a) .
Make sure that the holes on the Side
Bar (D) are facing up , and nearer the
headboard (A) .
STEP 3
b
c
D2
E
F
F
F
F
F
F
F
F
c
c
a
D2
D1
A
a

6
Repeat step 3 for the Footboard
(B) as shown .
STEP 4
STEP 5
a
a
a
a
c
B
a
e
e
a
e
A
C1
C2 D1
D2
c
c
e
1.Connect right bed rail (C1) to the right
side bar (D1) using bolt (e),Then connect
the right bed rail (C1) to the headboard (A)
by using bolts (a)&(e) and barrel nut (c).
2.Connect left bed rail (C2) to the left
side bar (D2) using bolt (e),Then connect
the left bed rail (C2) to the headboard (A)
by using bolts (a)&(e) and barrel nut (c).

7
Attach the Middle Panel (J) to the
center of the Drawer Back Panel
(I) using Wood Dowel (c),Cam
Bolt (g) and Cam.
Attach the Bottom Support Bar (K)
to the center of the Drawer Back
Panel (I) using Cam Bolt (g)
and Cam (h) .
STEP 7
Attach both Drawer Right Side (H1)
and Drawer Left Side (H2) to the
Drawer Back Panel (I) by inserting
4pcs Cam Bolts (g) to the end holes
of the Drawer Side Panel (H) as
shown . Make sure the grooves
line up and face inside.Insert 4pcs
Cams (h) into the holes of Drawer
Back Panel (I) . Lock the Cams (h)
in the Drawer Back Panel (I) using
phillips-head screwdriver .
STEP 6
I
H1
H2 g
h
h
h
hg
f
I
KJ

8
Attach Drawer Front Panel (G) by
inserting Cam Bolts (g) into their
corresponding Cam Bolts holes on
ends of Drawer Side Panel (H) ,
the Bottom Support Bar (K) and the
Middle Panel (J) . Make sure the
Drawer Bottom Panels (L) are also
inserted into grooves of Drawer
Front Panel (G) . Lock Cams (h) by
turning them clockwise .
Place the whole drawer flat on the
floor with the back up . Screw the
screw (i) from the middle of the
Bottom Support Bar (K) to the
Middle Panel (J) , as the image
shown .
STEP 9
Slide Drawer Bottom Panels (L)
painted side up , into grooves of
Drawer Side Panel (H) , the
Bottom Support Bar (K) and the
Middle Panel (J) as shown .
STEP 8
L
L
KJ
H1
H2
G
K
L
L
H1
H2
g
g
g
h
h
h
h
i

9
Congratulations , your toddler bed with drawer is ready to use .
STEP 11
Line up the drawer with the
wheels and mental tracks on
each side .
With the front slightly elevated ,
slide into the track on the end ,
lowering the front as it rolls into
place under the toddler bed .
STEP 10