Dream On Me HYGGE User manual

Read all instructions before
assembling and using product.
IMPORTANT - Keep instructions for
future use. 0622R1-787
Owner’s Manual
HYGGE
Changing Table
Scan the QR code to register your product
https://dreamonme.com/customercare/registration/

SAFETY TIPS
Contact Dream On
Me in case of any
assistance needed.
2www.dreamonme.com/help
Adult Assembly
Required.
DO NOT use the
product if it is
damaged, broken,
and/or components are
missing or broken.
To protect your parts
during assembly,
please place them on a
soft surface.
Small parts may
present choking
hazard prior to
assembly.
Please read the
instructions
thoroughly. Identify all
parts & hardware.
Do Not Use Power
Drills or Drivers.
To clean surface, use
only water on a damp
cloth. Do not use
window cleaner or
cleaning abrasive as it
will scratch the surface
and could damage the
protective coating.
0-6
Always monitor your
child’s activity in the
nursery or near
furniture.

…. for choosing Dream On Me and congratulations on joining our family;
a family that has been transforming lives for over 30+ years!
We appreciate your feedback and wish you the very best in the
coming years with your new addition. If you have any questions
or concerns please don’t hesitate to reach out to us. One of our
trusted Customer Care representatives will be happy to assist you.
Thank you again for entrusting us to provide you with safe
and affordable baby products and accessories.
THANK YOU...
LIMITED WARRANTY:
• Dream On Me warrants its product to be free from defects in material and
workmanship and agrees to remedy any such defect.
• This warranty covers 1 year from the date of original purchase.
• This warranty is valid only upon presentation of proof of purchase.
• This is solely limited to the repair or replacement of defective furniture
components and no assembly labor is included.
• This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or
repaired in any way.
• This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
www.dreamonme.com/help 3

www.dreamonme.com/help
4
WARNINGS
• FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
• READ ALL INSTRUCTIONS BEFORE ASSEMBLING CHANGING TABLE. KEEP INSTRUCTIONS FOR
FUTURE USE.
• FOLLOW ALL THE INSTRUCTIONS STRICTLY TO USE THIS CHANGING TABLE.
• BEFORE EACH USE OR ASSEMBLY, INSPECT THE UNIT FOR DAMAGED HARDWARE, LOOSE JOINT,
MISSING PARTS, OR SHARP EDGES.
• DO NOT USE THE UNIT IF ANY PARTS ARE MISSING OR DAMAGED. CONTACT DREAM ON ME INC.,
1532 S, WASHINGTON AVE, PISCATAWAY, NJ, USA, FOR REPLACEMENT PARTS AND
INSTRUCTIONAL LITERATURE IF NEEDED. DO NOT SUBSTITUTE PARTS.
• BE SURE TO USE THE PROPER SIZE AND SHAPE OF THE SCREWS/BOLTS SPECIFIED IN THE
INSTRUCTIONS DURING THE ASSEMBLY PROCESS.
• ASSEMBLY SHOULD BE DONE ON A SOFT, NON-ABRASIVE SURFACE TO AVOID DAMAGE TO THE
FINISH.
• KEEP CHILDREN AND OTHERS SAFE BY FOLLOWING THESE SIMPLE RULES:
- DO NOT ALLOW ANY CHILD TO PLAY ON FURNITURE.
- DO NOT ALLOW CLIMBING ON ANY PIECE OF FURNITURE.
- DO NOT ALLOW HANGING FROM ANY PIECE OF FURNITURE.
• ALWAYS MONITOR YOUR CHILD’S ACTIVITY WHEN IN THE NURSERY.
CHOKING HAZARD:
• KEEP UNASSEMBLED PARTS OUT OF THE REACH OF SMALL CHILDREN. USE ONLY THE PARTS,
HARDWARE, AND CHANGING PAD PROVIDED BY DREAM ON ME.
FALL HAZARD:
• TO PREVENT DEATH OR SERIOUS INJURY, ALWAYS KEEP THE CHILD WITHIN ARM’S REACH.
NEVER LEAVE THE CHILD UNATTENDED.
• USE ONLY THE PAD PROVIDED BY THE MANUFACTURER.
• DO NOT USE CHANGING TABLE, ADD-ON CHANGING UNIT, OR CONTOURED CHANGING PAD IF IT
IS DAMAGED OR BROKEN.
• MAXIMUM WEIGHT OF CHILD: 30 POUNDS (13.6 KG).
• ALWAYS USE THE SAFETY BELT PROVIDED. AS AN EXTRA PRECAUTION, KEEP AT LEAST ONE
HAND ON YOUR BABY AT ALL TIMES.
• DO NOT ALLOW ANY CHILDREN TO CLIMB OR PLAY ON THE TABLE.
• PERIODICALLY CHECK TO MAKE SURE ALL THE BOLTS AND SCREWS REMAIN TIGHT.
STRANGULATION HAZARD:
• STRINGS CAUSE STRANGULATION. DO NOT PLACE ITEMS WITH A STRING AROUND A CHILD’S
NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS.
• DO NOT SUSPEND STRINGS OVER A CHANGING TABLE OR ATTACH STRINGS TO TOYS.
• TO HELP PREVENT STRANGULATION, TIGHTEN ALL FASTENERS. A CHILD CAN TRAP PARTS OF
THE BODY OR CLOTHING ON LOOSE FASTENERS.
• DO NOT PLACE CHANGING TABLE NEAR THE WINDOW WHERE CORDS FROM BLINDS OR DRAPES
MAY STRANGLE A CHILD.
• NEVER USE PLASTIC SHIPPING BAGS OR ANY PLASTIC FILM AS CHANGING PAD COVER AS THEY
CAN CAUSE SUFFOCATION.
CLEANING:
• TO CLEAN THIS PRODUCT, USE MILD HOUSEHOLD SOAP AND WARM WATER.
• DO NOT USE BLEACH OR DETERGENT. DO NOT USE ABRASIVE CLEANERS THAT CAN HARM THE
FINISH OF THE PRODUCT.
• USE SOFT CLEAN CLOTHS TO WASH, RINSE AND DRY. WITH PROPER CARE, THE QUALITY FINISH
WILL LAST A LONG TIME.
• SURFACES OF WOOD CAN BE TREATED WITH NON-TOXIC FURNITURE POLISH.

www.dreamonme.com/help 5
PARTS
If there are any missing parts, please contact Dream On Me before using the
product.
Left End Frame
1Right End Frame 2Rear Rail 3
Front Rail
4Top Shelf Inserts 5Shelf Inserts (x2) 6
Base Stretcher (x2)
7Center Base Rail (x2) 8
Right Front and
Left rear Feet (x2)
10
Mattress Pad
11
Left Front and
Right Rear Feet
(x2)
9

www.dreamonme.com/help
6
HARDWARE
If there are any missing parts, please contact Dream On Me before using the
product.
Bolt M6 X 55mm (×4)
ABolt M6 X 45mm (×8) BBolt M6 X 40mm (x12) C
Bolt M6 X 20mm (×2)
DWasher (×2) ENut (x2) F
Metal Pin (×16)
H
Half Moon
Washer (x8)
G
Allen Key (x1)
J
Restraint Harness
I
Wrench (NOT INCLUDED)
Tools Needed:

www.dreamonme.com/help 7
Bolt M6 X 45mm (×4)
BHalf Moon
Washer (x4)
G
Metal Pin (×8)
H
(9)
(9)
(9)
(8)
(8)
(H)
(H)
(G) (B)
(8)
(10)
(10)
1
CHANGING TABLE ASSEMBLY - FEET ASSEMBLY
1a. Place all the parts on a soft
surface before assembly. Align
the Left Front and Right Rear Feet
(9) and the Right Front and Left
rear Feet (10) to the Center Base
Rail (8) as shown in the
illustration.
1b. Place the Metal Pins (H) between
the Left Front and Right Rear Feet
and Center Base Rail. Similarly,
place the Metal Pins between the
Right Front and Left rear Feet and
the Center Base Rail.
1c. Position the Half Moon Washer
(G) in the designated slots on the
Center Base Rail. Similarly, attach
the Bolts (B) in the insertions
provided on the Center Base Rail,
fixing them to the Feet.
1e. Tighten the Bolts using the Allen
Key (J) provided. Follow the
above steps for the second
Center Base Rail.
NOTE:
1. Do not overtighten the bolts.

www.dreamonme.com/help
8
Bolt M6 X 45mm (×4)
BHalf Moon
Washer (x4)
G
Metal Pin (×8)
H
(9)
(7)
(7)
(7)
(9)
(H)
(H) (G) (B)
(10)
(10)
(10)
2
CHANGING TABLE ASSEMBLY - BASE ASSEMBLY
2a. Align the assembled feet to the Base Stretcher
(7). Position the Metal Pins (H) between the four
feet and the Base Stretcher.
2b. Position the Half Moon Washers (G) in the
designated slots on the Base Stretcher (7).
Similarly, attach the Bolts (B) in the insertions
provided on the Base Stretcher,
fixing them to the feet.
2c. Tighten the Bolts using the Allen
Key (J) provided.

www.dreamonme.com/help 9
Bolt M6 X 40mm (x6)
C
(3)
(3)
(2)
(2)
(1)
(C)
(C)
(C)
(C)
(C)
(C)
(C)
3
CHANGING TABLE ASSEMBLY - RAIL AND FRAME ASSEMBLY
3a. The Rear Rail (3) should be
upright and aligned with the
Left End Frame (1) and the
Right End Frame (2), as shown
in the illustration below.
3b. Attach the Bolts (C) in the
insertions on the left and
right frames and tighten
them using the Allen Key (J)
provided.

www.dreamonme.com/help
10
(5)
(6)
(6)
4
CHANGING TABLE ASSEMBLY - SHELF ASSEMBLY
4a. Align the Top Shelf Insert
(5) and the Shelf Inserts (6)
to the assembled frame as
shown in the illustration.
4b. Install the Top Shelf Insert
in the highest slot of the
frame. Additionally, install
the Shelf Inserts (6) in the
two slots provided at the
bottom.

www.dreamonme.com/help 11
Bolt M6 X 40mm (x6)
C
(4)
(4)
(C)
(C)
(C)
(C)
(C)
(C)
(C)
5
CHANGING TABLE ASSEMBLY - FRONT RAIL ASSEMBLY
5a. Align the Front Rail (4) to
the half-assembled
changing table.
5b. Attach the Bolts (C) in the
insertions on the frames.
Tighten the bolts using the
Allen Key (J).

www.dreamonme.com/help
12
(A)
(A)
(A)
(A)
(A)
Bolt M6 X 55mm (×4)
A
6
CHANGING TABLE ASSEMBLY - FEET ASSEMBLY
6a. Lay the half-assembled
changing table on its
back. Align the
assembled base to the
shelf and panel assembly
as shown in the
illustration.
6c. Attach the Bolts (A) in the
insertions on the bottom
of the Base Stretcher,
fixing the base to the
bottom of the rails.
Tighten the bolts using
the Allen Key (J)
provided.

www.dreamonme.com/help 13
Restraint Harness
I
(D)
(E)
(F)
(I)
Bolt M6 X 20mm (×2)
DWasher (×2) ENut (x2) F
7
CHANGING TABLE ASSEMBLY - SAFETY RESTRAINT
HARNESS ASSEMBLY
7a. Unlock the Restraint Harness
Belts, and place the belts below
the top Panels as shown in the
diagram.
7b. Bring the belt from behind the Top
Rail onto the Top Panel.
7c. Align the Nuts (F) below the Belt
and the Washer (E) and the Bolt
(D) from above the Top Panel so
that the belts stay intact in their
place.
7d. Tighten the Nuts using a wrench
(not provided in the box), and
tighten the Bolts using the Allen
Key (J).
7e. Follow the same steps for the
other side of the belt.

www.dreamonme.com/help
14
(11)
8
CHANGING TABLE ASSEMBLY - MATTRESS PAD ASSEMBLY
8a. Place the Mattress Pad (11) onto
the Top Shelf Insert on the
attached strap.
8b. Make sure that the locking system
comes at the center. Adjust the
length accordingly.

www.dreamonme.com/help 15
FURNITURE CARE INSTRUCTIONS
ROOM CLIMATE CONTROL:
• Wood, when first cut contains more than 50 percent water. When it is prepared for
furniture construction it is placed in a Kiln and the moisture content is brought down
to 8 to 10 percent. Wood is porous and responds to its environment. If the room has
high humidity it will absorb it and expand and if the humidity is low it will lose
moisture and shrink.
• It is important that the humidity levels in the room be controlled from extremes of
too much humidity or too little. Furniture should not be placed close to the
air-conditioning outlets, fire places, radiators, space heaters, humidifiers or
dehumidifiers. Exposure to extreme variations of temperature and humidity can
damage any fine wood product.
THE IDEAL ENVIRONMENT FOR FINE FURNITURE:
• Fine wood furniture will have fewer problems when its environment is controlled at a
temperature between 65 and 75 degrees and a relative humidity between 35 and 40
percent. Wood placed in an environment outside of those limits can and will shrink
or expand and may develop some small cracks which are not material or structural
defects.
STICKING DOORS AND DRAWERS:
• With the minor changes in temperature and humidity, doors and drawers may swell
and be difficult to open or close. Tolerances have been built into the units but
extreme conditions may still cause sticking. This will adjust back to normal over
time but until it does consider using a dehumidifier or rub candle wax or paraffin on
sides that stick.
AVOID DIRECT SUNLIGHT:
• Keep the furniture out of direct sunlight. Ultraviolet rays will fade colors and in some
cases darken them. It can also cause crazing or hair line cracks in the finish. White
finishes will yellow naturally over time and exposure to direct sunlight will hasten
this natural process along with some woods darkening naturally over time; this is
not considered to be a quality defect.
PROPER STORAGE:
• If you need to put your furniture in storage for any period of time do not store them
in a damp basement or hot dry attic. Allow air movement around the furniture and
do not stack anything on it.

www.dreamonme.com/help 16
FURNITURE CARE INSTRUCTIONS (cont.)
IN GENERAL:
• Protect furniture surface from hot or extremely cold items.
• Use coasters under hot or cold beverages.
• Do not use synthetic fabric under accessories or lamps.
• Protect tops from pens, markers and crayons.
• Oils from potpourri and other scented items can damage the finish of the furniture.
• Do not drag items across the surface of the furniture.
• Allow the surface to breath by rotating your accessories and lamps.
• Do not over polish the furniture, do it only two or three times a year. Over polishing
can distort the natural finish of the product.
• Do not wax the furniture, as wax build up can destroy natural finish of the product.
• When moving furniture always lift the unit. Do not push or drag it to avoid damage
to legs.
• Keep the furniture level so doors and drawers open and close freely.
• Clean with a damp, not wet, cloth. Use only a mild soap. Do not use the abrasive
cleaners.
• Do not scratch or chip the finish.
• Inspect the product periodically, contact Dream On Me for replacement parts or
questions.
• Do not store the product or any parts in extreme temperatures and conditions such
as a hot attic or a damp, cold basement. These extremes can cause a loss of
structural integrity.
• To preserve the luster of the high-quality finish on your product, it is recommended
to place a doily or felt pad under any items you place on the finish.
• Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty
of this fine finish.
• Do not use abrasive chemicals.
• Do not spray cleaners directly onto furniture.
• Lift slightly when moving on carpeting to prevent leg breakage.
• Use of a vaporizer near furniture will cause wood to swell and to peel.
YOU DID IT!
Congratulations Mom & Dad!
It's time to create your dream nursery. A safe, elegant,
handcrafted changing table that grows with your little one.

1532 S. WASHINGTON AVE STE1
PISCATAWAY, NJ 08854-9908
www.dreamonme.com
Follow Us @dreamonmeinc
to get your nursery featured on our social media.
Enter our monthly giveaway!
Scan the QR code to register.
Chat with us!
Scan the QR code to Live Chat.
E-mail: [email protected]

Lisez toutes les instructions avant avant d'assembler
et d'utiliser le produit.
IMPORTANT- Conservez les instructions pour pour
une utilisation ultérieure. 0622R1-787
Manuel du propriétaire
HYGGE
Table à langer
Scannez le code QR pour enregistrer votre produit
https://dreamonme.com/customercare/registration/

CONSEILS DE SÉCURITÉ
Contactez Dream On
Me Inc en cas de
besoin d'assistance.
2www.dreamonme.com/help
Assemblage par un
adulte requis.
NE PAS utiliser le
produit s'il est
endommagé, cassé,
et/ou si des
composants sont
manquants ou cassés.
Pour protéger vos
pièces pendant le
montage, veuillez les
placer sur une surface
souple.
Les petites pièces
peuvent présenter
un risque
d'étouffement avant
l'assemblage.
Veuillez lire
attentivement les
instructions. Identifiez
toutes les pièces et le
matériel.
N'utilisez pas de
perceuse ou de
perceuse
électrique.
Pour nettoyer la surface,
utilisez uniquement de
l'eau sur un chiffon
humide. N'utilisez pas de
nettoyant pour vitres ou
d'abrasif de nettoyage,
car ils rayeraient la
surface et pourraient
endommager le
revêtement protecteur.
0-6
Surveillez toujours
l'activité de votre
enfant dans la
chambre d'enfant ou
près des meubles.

... pour avoir choisi Dream On Me et félicitations pour avoir rejoint notre
famille ; une famille qui a transformé des vies depuis plus de 30 ans ! Nous
apprécions vos commentaires et nous vous souhaitons le meilleur dans les
années à venir avec votre nouvelle addition. Si vous avez des questions ou
des préoccupations, n'hésitez pas à nous contacter. L'un de nos
représentants du service clientèle se fera un plaisir de vous aider. Merci
encore de nous avoir fait confiance pour vous fournir des produits et
accessoires pour bébés sûrs et abordables. produits et accessoires pour
bébés sûrs et abordables
MERCI...
GARANTIE LIMITÉE :
• Dream On Me garantit que son produit est exempt de tout défaut de
matériel et de fabrication et s'engage à remédier à tout défaut de ce type.
• Cette garantie couvre 1 an à partir de la date d'achat originale.
• Cette garantie n'est valable que sur présentation d'une preuve d'achat.
• Elle est uniquement limitée à la réparation ou au remplacement des
composants défectueux du meuble et aucune main d'œuvre de montage
n'est incluse.
• Cette garantie ne s'applique pas à un produit qui a été mal assemblé,
soumis à une mauvaise utilisation ou à un abus ou qui a été modifié ou
réparé de quelque façon que ce soit.
• Cette garantie vous donne des droits légaux spécifiques et vous pouvez
également avoir d'autres droits qui varient d'un État à l'autre. droits qui
varient d'un État à l'autre.
www.dreamonme.com/help 3