Dretec Popola 6 User manual

21-02
ー2ーー 1ー ー 3ー
Names of Each Part
<Front side> <Rear side>
Display
START/STOP
button
10 MIN button
RESET button
10 SEC button
TIMER/CLOCK
button
1 MIN button
Hook
Battery
cover
Stand
Magnet
Digital Timer “Popola 6”
Ｔ-792
22-04
Safety Precautions
●Be sure to read this “Safety Precautions” carefully
before use and use the product in a correct manner.
●The precautions described herein are matters about
safety, and therefore, be sure to observe them.
Matters must not to be done
Prohibition
Instruction
Matters must be done
Instruction Manual
Thank you for purchasing our product. Be sure to
read this instruction manual thoroughly before use,
and use this product in a safe and correct manner.
After reading this manual, keep it at hand with care to
make it possible to see it at any time.
Importer / Contact: SUNSATA
Phone: [phone]
Manufacturer: dretec
Address: 2-3-9 Ryutsudanchi Koshigayashi Saitama
About Battery
● Do not short-circuit the batteries, do not disassemble or
heat the batteries, and do not throw the batteries into fire.
● If your skin or clothing comes into contact with the battery
liquid, wash it away with water completely. If your eye
comes into contact with it, wash it away with clean water
and then see a doctor as soon as possible.
● Do not leave the batteries within the reach of an infant. In
case a battery is swallowed, see a doctor as soon as
possible.
● Pay attention to the polarities (+/-) of the batteries and put
them in the product in a correct manner.
● When the batteries are exhausted or the product is not
used for a long period of time, remove the batteries.
● When you dispose of the batteries, follow the local
instructions.
● Do not use an old battery with a new battery in a mixed
manner.
● Do not use different types of batteries or batteries of
different manufacturers in a mixed manner.
● If an unprecedented difference such as heat generation
from the batteries or battery deformation is observed when
the product is used or stored, stop using it.
* The illustrations described on this book are images.
Prohibition
Instruction
●Never disassemble, repair, or remodel the product.
Failure to observe this may cause ignition, electric
shock, or injury.
●Do not leave the product within the reach of an
infant and a person who cannot operate it by
him/herself.
Failure to observe this may cause accidental
swallowing or injury.
● If an abnormality or a failure is observed, stop
using the product immediately.
Failure to observe this may cause ignition, electric
shock, or injury.
Caution
Prohibition
Instruction
●Do not apply a strong impact to the product for
example by dropping it or bumping it.
●Do not store or use the product in a damp place
or a water splashing place because the product is
not waterproof or dripproof.
Failure to observe this may cause a failure.
●Do not leave this product in a place where direct
sunlight hits or the temperature becomes hot.
●Do not apply fire to the product directly or put it
near fire.
●Do not put solvents or chemical solutions on the
product.
Failure to observe this may cause the main unit to be
deformed, which results in a failure.
● When this product is used by hanging it with a
hook or attaching it with a magnet, make sure not
to drop.
● When this product is used by raising it, open the
stand until it stops, and put it on a horizontal and
stable place.
● Keep its magnet away from a magnetic card,
magnetic tape, and the like.
● When the product is carried, refrain from using it
close to a device that generates static electricity
such as a pacemaker or electromagnetic waves
such as a microwave oven, and an IH cooker.
Failure to observe this may cause a failure or a
malfunction.

ー5ーー 4ー ー 6ー
■Clock setting
■Count up
■Counting down
Product No./Product name T-792, Digital Timer “Popola 6”
Display method Liquid crystal digital 4 digits
Alarm sounding time Approx. 15 seconds
Max. settable time
Max. measurable time
for counting up
99 minutes 50 seconds
Battery AAA dry battery x 1 pc.
Battery life Approx. 1 year (when an alarm is
issued for 30 seconds in a day)
Operating temperature range 0 to 40○C
99 minutes 59 seconds
Clock accuracy Monthly rate: ±30 seconds
Battery Replacement
* Battery: AAA dry battery
(Fig. 1) (Fig. 2)
*The supplied battery is just for checking operation. The life may
be short.
1. Open the stand on the rear side of the main unit, and
remove the battery cover by sliding it in the arrow direction.
(Fig. 1)
2. Remove the old battery and put a new battery in the product.
* Be careful with the polarity (+/-) of the battery when putting a
battery in the product. (Fig. 2)
3. Close the battery cover by sliding it.
How to Use
The power cannot be turned on
• Check to see whether the polarity (+/-) of the battery is correct.
• Replace the battery with new one.
The display is lighter
• Replace the battery with new one.
Specifications
How to Clean
When the main unit becomes dirty, wipe the unit with a
tightly squeezed wet cloth.
● If the unit becomes heavily dirty, wipe the unit with a cloth
containing a little of a neutral detergent for kitchen use.
●
Do not use boiling water, alcohol, thinner, benzine, and the like.
Failure to observe this may cause discoloration,
deformation, and breakage.
● Never wash the product in water.
Do not splash water directly on the product, and do not let
the product contact with detergents. Failure to observe
this may cause a failure.
Before concluding the matter is a failure
* Be aware that the specifications of the product are subject to
change without notice due to product improvement.
1. Press the [TIMER/CLOCK]
button to call the clock
display.
2. Hold down the [TIMER/CLOCK] button for three seconds or
more, and “Time” blinks with a beep.
3. Press the [10 MIN] and [1 MIN] buttons
to adjust “Hour.”
[10 MIN] button: An hour forward each time
this button is pressed once
[1 MIN] button: An hour backward each time
this button is pressed once
* Keeping on pressing these buttons moves forward or backward
faster.
* When the “AM/PM” mode is selected, automatic switching
between AM and PM is performed.
When the [TIMER/CLOCK] button is pressed after displaying a
time to be set, “Minute” blinks.
4. Press the [10 MIN] and [1 MIN]
buttons to adjust “Minute.”
[10 MIN] button: A minute forward
each time this button is pressed once
[1 MIN] button: A minute backward
each time this button is pressed once
5. Select a display mode.
Each time the [10 SEC] button is pressed, the display is
alternately switched between the “AM/PM” mode and “24 Hour”
mode. Select your favorite mode.
6. Press the [TIMER/CLOCK] button.
The clock starts and the settings are completed.
* If the “24 Hour” mode is selected, “24” is not displayed after time
setting.
* When the battery is replaced or removed, the time is reset to the
initial setting. The initial setting time is “12:00 AM.”
* If no operation is performed for approximately five minutes
during setting operation, the time is automatically set to the
displayed time and the clock moves according to the time.
1. Press the [TIMER/CLOCK] button to activate the timer
display.
2. Press the [RESET] button to set the display to “00M00S.”
* If the product is in the counting operation, press the
[START/STOP] button to let the product pause, and then, press
the [RESET] button.
3. Press the [10 MIN], [1 MIN], and [10 SEC] buttons to set the
time.
Example1): When the time is set to 35 minutes and 40 seconds,
press the [10 MIN] button three times → press the [1 MIN] button
five times → press the [10 SEC] button four times.
* Keeping on pressing the [10 MIN], [1 MIN], and [10 SEC] buttons
moves the setting number faster.
4. Pressing the [START/STOP] button starts counting down,
and when a set time elapses, an alarm is issued for
approximately15 seconds.
* To stop the alarm, press any button.
(Repeat function: Even if the alarm is stopped by pressing any
button, the time returns to the former set time.)
* Pressing the [START/STOP] button during counting down allows
the product to pause. To continue counting down, press the
[START/STOP] button again.
* Pressing the [TIMER/CLOCK] button during counting down
allows the clock to be displayed, but counting down continues,
and when a set time elapses, an alarm is issued.
1. Press the [TIMER/CLOCK] button to activate the timer
display.
2. Press the [RESET] button to set the display to “00M00S.”
3. Pressing the [START/STOP] button starts counting up.
4. Pressing the [START/STOP] button during counting up
allows counting up to pause. To restart counting up, press
the [START/STOP] button again.
* Keeping on pressing these buttons moves forward or backward
faster.