Drive 12021KD-1 User manual

www.drivemedical.com
deluxe bariatric
shower chair
with back
item # 12021KD-1
www.drivemedical.com
EU Authorized Representative
Drive Medical LTD
Ainley’s Industrial Estate
Elland, West Yorkshire,
United Kingdom HX5 9JP
Rev.7.1.26.18

parts diagram/list
Weight capacity 500 lbs (226 Kg)
A B C D
E F
H I
JJ K
L2
L1
MM
A- Long Center Screw (1)
B- Flat Head Screw (4)
C- Backrest Screws (4)
D- Cross Brace Screws (9)
E- Washers (6)
F- Nuts (9)
G- U-Clips (6)
H- Seat
I- Backrest
J- Backrest Frame
K- Cross Brace
L- Leg Receivers
M- Legs
1. Remove contents from carton and verify that all
parts in the parts diagram/list are present.
2. Assemble the leg receivers
a. Take the seat (H) and turn it upside-down so that
the screw holes are facing upwards.
b. Take the leg receiver labeled “#1” (L1) and place it
into the groove labeled “#1” in the seat with the leg
receiver holes pointing upwards.
c. Take the leg receiver labeled “#2” (L2) and place
it into the groove labeled “#2” in the seat with the
leg receiver holes pointing upwards.
d. Insert screw (A) into the center screw hole through
both leg receivers but do not fully tighten the screw.
e. Secure Leg Receiver #1 using 2 flat head screws (B).
f. Secure Leg Receiver #2 using 2 flat head screws (B).
g. Tighten the center screw.
A
B B
B
B
3. Assemble the leg cross-brace
a. Take the two leg cross-braces (K) and place one on
top of the other with the grooves properly aligned.
D
KK
G
E
E

c. Position the cross-brace assembly in between the
four legs and align the cross-brace screw holes
with the cross-brace bracket screw holes.
d. Insert a screw (D) into each of the 8 screw holes
and secure with a nut .
D
DD
D
4. Assemble backrest
a. Take the backrest and the two L-shaped tubes (J).
b. Place each of the tubes into the grooves on the
rear face of the backrest (I).
c. Align the 2 screw holes in the L-shaped tubes with
the holes in the rear face of the backrest.
d. Place a washer (E) over each of the screw holes
and secure the L-shaped tube to the backrest
using 2 screws (C) for each tube.
e. Insert the backrest assembly tubes into the back
rest receiver on the underside of the seat.
f. Secure the backrest assembly to the seat using 2
U-shaped clips (G).
5. Assemble legs
a. Insert a leg (M) into each of the leg receivers.
b. Adjust each leg to the same height and align the
height-adjustment holes in the legs with the holes
in the leg receivers.
c. Use a U-shaped clip to secure each of the legs to
the leg receiver.
J J
I
C
C C
C
Item # 12021KD-1
b. Place 2 washers (E), one on both sides of the
cross-braces. Insert screw (D) through washers (E)
and into the center hole and secure with a nut (F).

1. Inspect all parts for shipping damage before
assembly. If there is shipping damage - DO
NOT USE. Contact dealer/carrier for further
instructions.
2. Make certain that the U-Clips full protrude through
the same respective holes of each leg extension.
This will ensure that the leg extensions are securely
locked in position and an even height is achieved.
3. Ensure ALL screws, nuts and/or bolts are
tightened.
4. Check the rubber tips on the leg extensions
for rips, wear or if they are missing.
Immediately replace any or all if any of these
imperfections exist.
5. All four leg extensions with rubber tips MUST
touch the floor simultaneously at all times.
6. DO NOT stand on chair.
additional precautions
NOTE: To maintain the beauty of the original finish,
clean with mild soap and rinse with warm water. Wipe
bath seat dry aer each use.
lifetime limited
warranty
Your Drive branded product is warrantied to be free
of defects in materials and workmanship for the
lifetime of the product for the original consumer
purchaser.
This device was built to exacting standards and
carefully inspected prior to shipment. This Lifetime
Limited Warranty is an expression of our confidence
in the materials and workmanship of our products
and our assurance to the consumer of years of
dependable service.
This warranty does not cover device failure due to
owner misuse or negligence, or normal wear and tear.
The warranty does not extend to non-durable compo-
nents, such as rubber accessories, casters, and grips,
which are subject to normal wear and need periodic
replacement.
If you have a question about your Drive device or
this warranty, please contact an authorized Drive
dealer.
© 2018 Medical Depot, Inc. All rights reserved.
Drive is a trademark of Medical Depot, Inc.
Port Washington N.Y. 11050 USA Made in China
adjusting leg height
1. To adjust leg height, remove U-Clip adjustment
hole, set leg to desired height and return U-clip
into adjustment hole. Make sure U-Clip clicks into
place. Repeat for remaining legs.
NOTE: Make sure all legs are set to the same height.
2. To be sure legs are locked into place, push down or
pull up on legs.