ENGLISH 23ENGLISH
THE DT180P/ DT180T
Powering ON and OFF
The Power Buon is located in the front of the DT180P/ DT180T. The Power Buon may be
configured to funcon differently depending on the power opons of the operang system. In
general, to turn the DT180P/ DT180T on, push and release the Power Buon on the front bezel.
The adjacent power LED will be lit (blue) and the corresponding interface will be displayed on the
display monitor.
To turn offthe device, again depending on soware operang system, push and release the Power
Buon or use a soware shutdown interface. In the event of system lockup, the Power Buon may
be used to perform a reset on the device. To do that, push and hold the Power Buon for at least 4
seconds. The system will shut down and all unsaved work may be lost. Pushing on the Power Buon
again will restart the device.
Device Ports
The DT180P/ DT180T features an opmal set of I/O ports while preserving the compact size of
the system. The HDMI connector, Network (10/100/1000 BaseT Ethernet), and Power ports are
supplemented by a set of two USB 2.0 and two Audio ports. Through its USB ports, the DT180P/
DT180T supports a wide range of USB-based peripherals. These peripherals are applicable in
providing the means for soware installaon, applicaon storage, data storage, and system
soware recovery and updates.
Memory and Storage
The DT180P/ DT180T may be available in storage configuraons ranging 8GB of flash memory
or 32GB to 64GB SSD. Depending on base soware configuraon, the user may use the internal
memory of the DT180P/ DT180T for user’s installed soware and storage. The user may also
supplement storage space with USB-based peripherals such as flash disks, disk drives, etc. RAM
capacity is up to 2GB.
VESA Mounng Bracket Installaon Guide for DT180P/ DT180T
The DT180P/ DT180T package includes a VESA-compliant mounng bracket (1) which mounts the
DT180P/ DT180T (2) onto a VESA-compable monitor or display.
NOTE: The VESA Mounng Bracket is compable with most displays and monitors that support the VESA standard.
Precauons
Always exercise care when operang and handling the DT180P/ DT180T.•
Never disassemble any poron of the enclosure. It will void any product warranty on the•
DT180P/ DT180T.
Do not use any AC/DC adapter other than the one provided with the device or acquired from the•
manufacturer or its partners.
In the unlikely event that smoke, abnormal noise, or strange odor is present, immediately power•
down the DT180P/ DT180T and disconnect all power sources.
Please report the problem to your device provider immediately.•
Rear ViewFront View
ABCDFE GH
Ethernet port
HDMI port
VGA port
RS232 COM port
DC-in
D
F
E
G
H
A
B
C
Audio jacks
Power buon
USB 2.0 (2)
Step1:
Locate the exisng mounng holes on•
the monitor.
Line the bracket holes up with the holes•
on the back of the monitor, as shown
to the right.
Place the screws to hold the mounng•
bracket in place and ghten the screws
(do not over-ghten).
Step2:
Remove the two M3 screws (3) originally•
on the DT180P/ DT180T signage
appliance.
Place the DT180P/ DT180T (2) on the•
bracket rail with the interface ports
side facing downwards so that the two
mounng holes on the appliance are
aligned with the exisng holes on the rail
(see picture).
Step3:
Apply and ghten the screws•
into their original locaons and
make sure that the bracket and
the DT180P/ DT180T are properly
secured.
