DT Research 316T Assembly instructions

Mobile Tablet
Caution:
Disposal of a battery into fire or a hot oven, or mechanically
crushing or cutting of a battery, that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable。
316T
INTRODUCTION
Thank you for acquiring the 316T, part of DT Research’s line of Mobile Tablet.
Featuring a slim, robust enclosure, the 316T with a 15.6” TFT display is poweredby the
Intel® processor, offering optimal combinations of performance and power savings.
The 316T is available with Microsoft® Windows® or Ubuntu operating system.Each
software operating system features web browser, client/ server computing software,
media player, accessories, and applications support.
PACKAGE CONTENTS
•One 316T with Battery Pack and HandstrapF
•AC-DC Power Adapter with Power Cord
•Basic Operation Guide
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright © 2021, DT Research, Inc. All Rights Reserved. BOG120921 316T C ENG

2
3
Power/Battery LED Status:
•Blue indicates the battery is 25% to 100% charged
•Blinking blue indicates the battery is charging
•Orange indicates that the battery is between 11% to 25%
•Blinking Orange indicates that the battery is below 10%
PRECAUTIONS
•Always exercise care when operating and handling the 316T.
•Do NOT apply excessive pressure to the display screen.
•We recommend using the Digital Pen (optional) to keep the screen clean.
•Avoid prolonged exposure of the display panel to any strong heat source.
Wherever possible, the 316T should face away from direct light to reduceglare.
•If the AC-DC power adapter is used to recharge or power the tablet, do NOT use
any AC-DC adapter other than the one provided or acquired from the manufac-
turer or its partners.
•In the unlikely event that smoke, abnormal noise, or strange odor is present,
immediately power off the 316T and disconnect all power sources. Reportthe
problem to your device provider immediately.
•Never attempt to disassemble the 316T, as this will void the warranty.
Input/ Output Ports
Button Functions
BASIC FEATURES
The 316T wireless tablet integrates a bright and multi-touch display, one USB port,
and embedded networking elements such as wireless LAN and Bluetooth. The316T is
complemented by a suite of accessories, including battery expansion, charging cradles,
and battery charger kit, for a comprehensive user experience.
A 316T typically integrates an 802.11ax wireless LAN (WLAN) adapter that mayconnect
to other wireless devices or access points. If your 316T does not comewith such a
network adapter, please consult your device provider to establish the desired
network connectivity.
BHeadphone-out
CEthernet Port
A USB 3.0 Port
E DC-in
Battery/Power LED
3
A
B
C
A
D
1
2 E
BUTTON
ACTION
1
ProgrammableButton
2
Power Button
3
Battery Latch

4
5
OPERATION
Powering ON and OFF
To activate the 316T, push and quickly release the Power Button. The display will
come on in a few seconds. To put the 316T in Standby mode, push and quickly
release the Power Button. To turn the 316T off for extended storage, power
off safely using any software function that “shuts down computer” provided in the
software operating system.
Start Up
If the power up (from Standby mode or otherwise) is successful, the appropriate
interface will be displayed after a launch sequence of several seconds. The wireless
LAN connection may take 10-15 seconds to be established.
Configuring the Mobile Tablet
The 316T may be configured using the utilities and methods dictated by the
software operating system. The 316T should be configurable for various
properties such as user profiles, network features, and several system elements.
Wireless Networking
Wireless LAN
The 316T is often delivered with an embedded (user-inaccessible) 802.11ax
WLAN adapter equipped with a hidden custom antenna.
•Through the support of typical WLAN adapters, the 316T should be able to
detect all 802.11 access points in the vicinity for you to select the access point of
your choice for connection.
•The SSID and WEP/WPA/WPA2 (if enabled) parameters on the 316T and the
access points have to match. The SSID is case-sensitive and it is recommended
that you enable WEP/WPA/WPA2 encryption (or advanced alternatives) for
secure access.
•When WEP/WPA/WPA2 is enabled, you may need to consult your network
administrator or your networking equipment literature to properly configure
associated settings such as Authentication mode, etc.
•Refer to the access point operating manuals for setting up the 802.11 access
points.
Bluetooth
The 316T offers the Bluetooth module which supports Bluetooth 5.0 standardincluding
Bluetooth 3.0 High Speed and Bluetooth 4.0 Low Energy, which delivers faster speeds
with low power consumption.
NOTE:
To conserve power, use (push and quick release) the Power Button to put the
tablet in “Standby” mode while not in use. Pushing briefly on the same button
will wake up the system within seconds.
NOTE:
When the batterypack is charging, the blue-colored Battery LED should blink
slowly. If plugging in the AC-DC adapter does not trigger this blinking activity
and the LED stays dark, the battery pack may have been drained substantially.
Try unplugging/ replugging the AC-DC adapter to the 316T a few times to
activate the charging process.
NOTE:
The battery packs shipped with your tablet may be low in power—please use
the AC-DC adapter with the 316T when setting up for the first time to fully
charge the internal battery pack. You may charge the external battery pack with
it attached to the 316T, or with the optional external battery charger kit.
NOTE:
Avoid using the Power Button (“hold 4+ seconds” feature) to turn off the tablet—
this form of hardware shutdown is intended to be a means of recoveryfrom
lockups, and not as normal operation.

6
7
USING THE MOBILE TABLET
Peripherals Support
Through its USB port, the 316T supports a wide range of USB-based peripherals.These
peripherals are applicable for software installation, applications storage, datastorage,
and system software recovery and updates.
For More Support
Users can download the Tablet Modules Basic Operation Guides from the DT
Research website.
The equipment is only suitable for mounting at heights ≤ 2 m.
The band 5150-5350 MHz for this device are restricted to indoor use only.
RF Exposure Compliance
This device was tested for typical body-worn operations. To comply with RF exposure requirements,
a minimum separation distance of 0mm must be maintained between the user’s body and the handset,
including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should
not contain any metallic components. Body-worn accessories that do not meet these requirements may
not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved
antenna.
Cet appareil a été testé pour des opérations typiques portées sur le corps. Pour se conformer aux
exigences d'exposition RF, une distance de séparation minimale de 0 mm doit être mainten ue entre
le corps de l'utilisateur et le combiné, y compris l'antenne. Les clips de ceinture, les étuis et les
accessoires similaires tiers utilisés par cet appareil doiventne contiennent aucun composant
métallique. Les accessoires portés sur le corps qui ne répondent pas à ces exigences peuvent ne
sont pas conformes aux exigences d'exposition RF et doivent être évitées. Utilisez uniquement le
produit fourni ou approuvé antenne.
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier Trade Name:
Model No.: 316T
Responsible Party –U.S. Contact Information
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
http://www.dtresearch.com
Federal Communication Commission Interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.

6
7
IC Compliance Statement
- English:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
- French:
Le present appareilest conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:(1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
RF Exposure Information (RED)
To be protected against all verified adverse effects, the separation distance of at least 0m must be maintained between the antenna of the radio having max. 4.1dBi antenna and all persons.
Hereby, [DT Research, Inc.] declares that the radio equipment type [316T] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following
internet address: http://www.dtresearch.com.
Maximum EIRP for EU
Bluetooth:2402MHz-2480MHz
10.44dBm
Bluetooth LE:2402MHz-2480MHz
7.09dBm
Wifi: 2412MHz-2472MHz/2422MHz-
2462MHz
18.49dBm
Wifi: 5150MHz-5725MHz
19.05dBm
Wifi: 5725MHz-5875MHz
13.92dBm