Dtronic DT3427 User manual

User Manual
DT3427
Barcodescanner –DT3427
:0645733500
: [email protected]
:https://www.dtronic.nl/
Datum :22-1-2024
Versie :1.0

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 2 van 15
Introduction
Thank you for trusting a product from DTRONIC. Please read the contents of the user manual
carefully in order to use the products safely and effectively.
You are advised to keep this manual correctly for your installation and as a reference. Please do not
disassemble the product or tear off the seal, otherwise we will not provide warranty or
replacement service.
The illustrations in this user manual are for reference only. If there are images that do not match
the actual product, please take the actual product as standard.
Updated information is subject to change without notice. All information in this manual is
copyrighted and our company reserves all rights. It is prohibited to distribute, copy, compile or sell
all or part of this manual without our written permission.
DTRONIC is a BOIP registered trademark and legally protected in cooperation with GS1. Diwolar is
the only company with the rights to market this trademark. If you have purchased a product that
was not purchased through Diwolar, the warranty is void. When contacting customer service
always ask for the order number. This user manual applies to DTRONIC barcode scanners that
identify barcodes using a laser scan pattern.
DTRONIC is not liable for damages and defects suffered when the barcode scanner fails, does not
work properly or is misused.
Do you have any questions about your product? We will be happy to assist you.
Mail: [email protected] Bereikbaar van 09:00-17:00u
WhatsApp: [phone] Bereikbaar van 09:00-17:00u
Website: www.dtronic.nl Webshop 24/7 geopend
Kind regards, team Dtronic
-Diederik Director
-Arjan Operations manager
-Marjolein Financial employee
-Jaxx Administrative employee
-Tim Customer service
-Hessel Customer service
- Roger Test center
- Kees-Jan Logistics

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 3 van 15
Inhoud
INTRODUCTION..........................................................................................................................2
1. PRODUCT.............................................................................................................................4
1.1 Function............................................................................................................................ 4
1.2 Unbox................................................................................................................................ 4
1.3 Start .................................................................................................................................. 4
1.4 Window............................................................................................................................. 4
1.5 Reading ............................................................................................................................. 5
1.6 Picture............................................................................................................................... 5
1.7 Led indicator..................................................................................................................... 5
2. SYSTEM SETUP .....................................................................................................................6
2.1 System Setup .................................................................................................................... 6
2.1.1 Setup code.............................................................................................................. 6
2.1.2 Restore factory default settings............................................................................. 6
2.1.3 Product User Settings............................................................................................. 6
2.2 Wireless ............................................................................................................................ 7
2.2.1 Bluetooth name...................................................................................................... 8
2.2.2 Beeper Duration..................................................................................................... 9
2.2.3 Beeper settings....................................................................................................... 9
2.3 Reading mode settings ..................................................................................................... 9
2.3.1 Level trigger mode.................................................................................................. 9
2.3.2 Continuous mode (default) .................................................................................. 10
2.3.3 Pulse trigger mode ...............................................................................................10
2.3.4 Auto Scan mode ................................................................................................... 10
2.4 Communication settings.................................................................................................10
2.4.1 Communication settings.......................................................................................10
2.4.2 USB keyboard .......................................................................................................11
2.4.3 USB keyboard sending speed...............................................................................11
2.5 Data format setting.........................................................................................................12
2.5.1 Hide 1 character ...................................................................................................12
2.5.2 Custom prefix on/off settings............................................................................... 13
2.5.3 Custom suffix on/off settings ............................................................................... 13
2.5.4 Data output settings............................................................................................. 13
2.6 Symbologies.................................................................................................................... 14
2.6.1 All barcodes.......................................................................................................... 14
2.6.2 Micro PDF417 .......................................................................................................14
2.6.3 Maxicode..............................................................................................................15
2.6.4 Aztec code ............................................................................................................15

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 4 van 15
1. Product
1.1 Function
- Works with Plug&Play and without installation software.
- Works with most WMS systems.
- Some WMS or POS systems must be set up to use a scanner.
- Device the scanner is connected to will see it as keyboard.
- Basically the scanner scans the 95% of bar codes, remaining 5% can be set as desired with this
manual.
- There are patented parts in the scanner, DTRONIC has the rights to sell these items on the
Dutch, Belgian and German market
1.2 Unbox
After opening the box containing the product, perform the following steps:
- Remove the scanner accessories from the packaging.
- Remove the scanner from the packaging.
- At the packing list, check that everything is complete and in good condition. If there are
damaged or missing parts, save the original packaging and contact DTRONIC for customer
service.
Packing list:
1. Handheld scanner
2. USB Connection Cable (for wireless scanners, this is the charging cable).
3. Paperclip
4. Abridged user manual
1.3 Start
Startup: connect the computer to the scanner. The computer will recognize it as a keyboard and the
scanner can be used.
Power off: remove the cable connected to the scanner; remove the USB connected to the
computer.
Restart: if the scanner crashes or is unresponsive, turn it off and restart it. Optionally, use the
factory setting from this manual
1.4 Window
The scanning window must be kept clean, the supplier does not bear the warranty responsibility
due to improper maintenance. Prevent the window from wearing out or being scratched by a hard
object. Use a soft cloth to remove stain on the scanning window. Clean the scan window with a soft
cloth, such as a lens cleaning cloth
Spraying liquid on the scan window is prohibited. Prohibit all cleaning solvents except cleaning
water.

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 5 van 15
1.5 Reading
If the bar code is small, it should be closer to the scan window; if the bar code is large, it should be
further away from the scan window for easier reading.
If the bar code is highly reflective (for example, the coated surface), you may need to tilt the bar
code at an angle to scan the bar code. The best distance to read a bar code is 10-15 cm
1.6 Picture
1.7 Led indicator
INDICATOR STATUS
EXPLAIN
Red light on
Charging
Red light off
No charging
Green light on
No decoding
Green light off
Decode succesfully
One blue light on
Pairing successful or connect to
USB

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 6 van 15
2. System Setup
2.1 System Setup
Option and function setting mainly by reading a series of special bar codes. In this chapter, we give
you a detailed introduction to the options and functions available for user setup and the
corresponding setup code.
This method of setting up the scan is direct, easy to understand and user-friendly.
2.1.1 Setup code
Startup settings (default)
Exit Settings
2.1.2 Restore factory default settings
Restore factory settings
2.1.3 Product User Settings
Save user default settings
Restore user default settings

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 7 van 15
2.2 Wireless
Bluetooth HID Mode
Quick Pair
Bluetooth SPP Mode
Bluetooth BLE Mode
Bluetooth BLE Mode
Android Input Method
USB-Virtual COM Port
Enable Long press to enter Bluetooth HID
Mode Pairing
Disable Long press to enter Bluetooth HID
Mode Pairing
Set custom Bluetooth device name
Query Bluetooth Name

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 8 van 15
2.2.1 Bluetooth name
First scan the "Bluetooth name setting" and then scan another barcode that becomes the Bluetooth
name of this scanner.
NOTE:
The longest Bluetooth name can be 16 bytes. If the Bluetooth barcode is more than 16
bytes, the Bluetooth takes only the first 16 bytes as the Bluetooth name.
NOTE:
Full Bluetooth name format, including: Bluetooth name + protocol type, you can only
change the Bluetooth name. After you change the Bluetooth name, all Bluetooth
names with different protocol type will be changed at the same time. For example, you
can change the Bluetooth name in "HID mode" to "Scanner", then the Bluetooth name
becomes "ScannerHID". In SPP and BLE protocol, this is "ScannerSPP" and
"ScannerBLE".
HID coupling step 1:
1. After activation, the green light of the scanner always remains on;
2. Scan "Enter Setting" >> "Pair Mode" >> "Bluetooth HID Mode" >> "Exit Setting."
3. Now green remains on and two blue lights flash alternately.
4. When the blue and green lights are on and the buzzer sounds, pairing is successful.
HID pairing step 2:
1. After activation, the green light of the scanner always remains on;
2. Press the button for 8S.
3. Now green remains on and two blue lights flash alternately.
4. When the blue and green lights are on and the buzzer sounds, pairing is successful.
SPP pairing step:
1. After activation, the green light of the scanner always remains on;
2. Scan "Enter Setting" >> "Pair Mode" >> "Bluetooth SPP Mode" >> "Exit Setting."
3. Now green remains on and two blue lights flash alternately.
4. When the blue and green lights are on and the buzzer sounds, pairing is successful.
BLE pairing step:
1. After activation, the green light of the scanner always remains on;
2. Scan "Enter Setting" >> "Pair Mode" >> "Bluetooth BLE Mode" >> "Exit Setting"
3. Now green remains on and two blue lights flash alternately.
4. When the blue and green lights are on and the buzzer sounds, pairing is successful.
NOTE:
Double-clicking the button during connection exits "Pairing Mode"; if the pairing is not
established within a minute, "Pairing Mode" exits.

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 9 van 15
2.2.2 Beeper Duration
Mute
2.2.3 Beeper settings
Volume set to High (50%) (default)
Volume set to midrange (25%)
Volume set to bass (12.5%)
2.3 Reading mode settings
2.3.1 Level trigger mode
Enter the reading state when the trigger key pin is at low level. Press and hold the trigger key to
start reading code. After reading the code successfully or releasing the trigger key, the code reading
ends and the next decoding needs to re-enter the low level state.
Level trigger mode

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 10 van 15
2.3.2 Continuous mode (default)
When the reading setting code is switched to this mode, it enters the continuous reading state. In
this mode, the "repeat read switch" can be used to prevent the same barcode from being read
more than once.
Continuous mode (default)
2.3.3 Pulse trigger mode
When the reading setting code is switched to this mode, it enters the pulse-triggered reading state.
Pulse trigger mode
2.3.4 Auto Scan mode
Auto scan
2.4 Communication settings
2.4.1 Communication settings
USB HID (default)
USB serial port

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 11 van 15
2.4.2 USB keyboard
Portuguese (Brazil) cannot output "?" and "/" .
Nederlands
Italian
Spanish (Brazil)
Portuguese
Portuguese (Brazil)
French
German (Austria)
English UK
Japanese
German (Switzerland)
French (Belgium)
America
2.4.3 USB keyboard sending speed
If there is missed data at the receiver side, the occurrence speed should be turned down, which is
easy to occur at the receiver side with poor performance.

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 12 van 15
5 ms (default)
10 ms
20 ms
2.5 Data format setting
Length of custom prefix and suffix: (0~10) characters, if set to "on", "Code ID prefix", "custom
prefix", "end suffix", etc. will be added before and after the decoding information. "Custom suffix",
"End suffix", etc.
The maximum number of data cache is 5, and the maximum length of individual data is 7900
characters; the data output is sequential output, and you need to wait for the first barcode output
to finish before the second barcode output, and so on.
2.5.1 Hide 1 character
Hide 1 from start
Hide 1 from the end

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 13 van 15
2.5.2 Custom prefix on/off settings
Custom prefixes add a user-defined string before the decoded information. For example, if you
allow to add a custom prefix and set the prefix to the string "AB", after reading the barcode with
the data "123", the scanner adds the string "AB" before the string "123", and the host side receives
"AB123". After the barcode reading data is "123", the scanner will add the string "AB" before the
string "123", and the host side will receive "AB123".
If set to "Off", the decoded information will only have the barcode data information, no prefix, and
the default value is to turn off the custom prefix output.
Enable
Disable (default)
2.5.3 Custom suffix on/off settings
The custom suffix adds a user-defined string after the decoded information. For example, it is
allowed to add a custom suffix and set the suffix to the string "AB", after reading the barcode with
the data of "123", the scanner adds the string "AB" after the string "123", and the host side receives
"123AB". After the barcode reading data is "123", the scanner will add the string "AB" after the
string "123", and the host side will receive "123AB".
If set to "Off", only the barcode data information will be in the decoded information, no suffix, and
the default value is to turn off the custom suffix output.
Enable
Disable (default)
Convert all to Uppercase
Convert All to lowercase
2.5.4 Data output settings
OPMERKING:
The prefix and suffix are not processed, and the prefix and suffix are output normally.

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 14 van 15
Raw data output (default)
Front-end data output
Intermediate data output
Back-end data output
Start and end data output
2.6 Symbologies
Each type of barcode has its own unique properties, and the setup codes in this chapter allow you
to adjust the scanner to accommodate these property changes.
The fewer barcode types that are turned on, the faster the scanner will Scan. You can turn off the
barcode types that will not be used to improve the performance of the scanner.
2.6.1 All barcodes
Close all barcodes
Turn on all barcodes
2.6.2 Micro PDF417
Enable
Disable

User manual ‘DT3427’
Datum : feb-2024
Versie : 1.0
pagina 15 van 15
2.6.3 Maxicode
Enable
Disable
2.6.4 Aztec code
Enable
Disable